Fabric Intermediate Screens - Partial Depth For Use With Tops With Hinged Access - Knoll Antenna Workspaces Installation Instructions Manual

Fabric Intermediate Screens - Partial Depth
for Use with Tops with Hinged Access
Pattern Numbers Represented:
Fabric Intermediate Screens,
YPSI__F
Parts List:
Bayonet Mount Bracket (A)
Upholstered Intermediate Screen Rail Clamp (B)
Upholstered Intermediate Screen Rail End Cap (C)
/ -18 x ¾" Machine Screw (D)
5
16
¼ - 20 x / " Black Oxide Machine Screw (E)
3
8
Non-Skid Pad (F)
¼ - 20 x / " Set Screw (G)
3
8
Intermediate Screens
Screen Bottom Extrusion
Screen
Planning and Specification Guidelines
Tools Needed:
Drill
Phillips #2 and #3 bits
/ " Allen Key
1
8
STEPS
0U[LYTLKPH[L ZJYLLUZ HYL KLZPNULK
1. Insert (2) bayonet mount brackets (A) into
[V WSHU HU`^OLYL HSVUN (U[LUUH IPN
the top of the screen bottom extrusion so
[HISLZ VY SPURLK KLZR JVUMPN\YH[PVUZ [V
that the holes in the brackets align with
KLSPULH[L PUKP]PK\HS ^VYRZWHJLZ the two sets of holes in the extrusion.
0U[LYTLKPH[L ZJYLLUZ PUJS\KL H WHPU[LK
2. Insert (4) / -18 x ¾" machine screws (D)
5
16
0U[LYTLKPH[L ZJYLLUZ HYL KLZPNULK
HS\TPU\T KLZR[VW TV\U[PUN IYHJRL[
beneath the extrusion and firmly attach the (2)
[V WSHU HU`^OLYL HSVUN (U[LUUH IPN
[OH[ Z\WWVY[Z MYHTLK [HJRHISL MHIYPJ VY bayonet mount brackets (A) to the extrusion.
[HISLZ VY SPURLK KLZR JVUMPN\YH[PVUZ [V
MYHTLSLZZ NSHZZ ]LULLY SHTPUH[L VY THYRLY
3. Insert (1) upholstered intermediate
KLSPULH[L PUKP]PK\HS ^VYRZWHJLZ
Z\YMHJL [V H OVYPaVU VM  VY  
screen rail end cap (C) into one end
0U[LYTLKPH[L ZJYLLUZ PUJS\KL H WHPU[LK
0U[LYTLKPH[L ZJYLLUZ HYL H]HPSHISL of the bottom screen extrusion.
HS\TPU\T KLZR[VW TV\U[PUN IYHJRL[
MVY [^V WSHUUPUN HWWSPJH[PVUZ! M\SS
[OH[ Z\WWVY[Z MYHTLK [HJRHISL MHIYPJ VY
4. Insert (1) hex head set screw (G) into the end cap
KLW[O HUK OPUNLK HJJLZZ KLW[O
MYHTLSLZZ NSHZZ ]LULLY SHTPUH[L VY THYRLY
(C) and secure it to the bottom screen extrusion.
Z\YMHJL [V H OVYPaVU VM  VY  
5. Peel the protective paper from one side
0U[LYTLKPH[L ZJYLLUZ HYL H]HPSHISL
of the non-skid pad (F) to expose one
MVY [^V WSHUUPUN HWWSPJH[PVUZ! M\SS
of the adhesive sides.
KLW[O HUK OPUNLK HJJLZZ KLW[O
6. Affix the non-skid pad (F) to the underside
of the bottom screen extrusion close to the
end cap (C) that has just been attached.
7HY[PHS +LW[O 0U[LYTLKPH[L
:JYLLU MVY <ZL ^P[O
/0UNLK (JJLZZ ;VWZ
7HY[PHS +LW[O 0U[LYTLKPH[L
:JYLLU MVY <ZL ^P[O
Partial Depth Intermediate Screen
/0UNLK (JJLZZ ;VWZ
for Use with Hinged Access Tops
Intermediate Screens
Planning and Specification Guidelines
-\SS KLW[O PU[LYTLKPH[L ZJYLLUZ JVYYLZWVUK
NOTE:
[V (U[LUUH [VW KLW[OZ        
OF THE PROTECTIVE PAPER AT THIS POINT.
  HUK H[[HJO ^P[O H JSHTW IYHJRL[ HYV\UK
7. Determine the desired screen position along
[OL MYVU[ HUK IHJR LKNLZ VM [OL [VW
the width of the table, and position the screen
0U[LYTLKPH[L ZJYLLUZ MVY OPUNLK HJJLZZ [VWZ
extrusion on the worksurface accordingly.
-\SS KLW[O PU[LYTLKPH[L ZJYLLUZ JVYYLZWVUK
      HYL SLZZ KLLW [OHU OPUNLK
8. Hook (1) upholstered intermediate screen rail
[V (U[LUUH [VW KLW[OZ        
[VWZ [V LUHISL M\SS \ZL VM OPUNL MLH[\YL ;OL`
clamp (B) to the front edge of the worksurface
  HUK H[[HJO ^P[O H JSHTW IYHJRL[ HYV\UK
H[[HJO ^P[O H JSHTW IYHJRL[ HYV\UK [OL MYVU[
so that the clamp's u-channel is above the
[OL MYVU[ HUK IHJR LKNLZ VM [OL [VW
LKNL VM [OL [VW HUK H UVUZRPK WHK VU [OL [VW
worksurface and the two screw holes are below
0U[LYTLKPH[L ZJYLLUZ MVY OPUNLK HJJLZZ [VWZ
*VUZ[Y\J[PVU the worksurface. Slide the open end of the
      HYL SLZZ KLLW [OHU OPUNLK
bottom screen extrusion onto the u-channel
-HIYPJ ZJYLLUZ HYL  ë [OPJR ^P[O WLYPTL[LY
[VWZ [V LUHISL M\SS \ZL VM OPUNL MLH[\YL ;OL`
portion to temporarily support the bracket.
L_[Y\KLK HS\TPU\T MYHTL L_[Y\KLK HS\TPU\T
H[[HJO ^P[O H JSHTW IYHJRL[ HYV\UK [OL MYVU[
IHZL MYHTL JHZ[ HS\TPU\T JSHTW IYHJRL[Z
LKNL VM [OL [VW HUK H UVUZRPK WHK VU [OL [VW
9. Lifting the free end of the screen assembly
HUK JHZ[ HS\TPU\T IH`VUL[Z ;HJRHISL
slightly, carefully peel the protective paper
*VUZ[Y\J[PVU
MHIYPJ Z\YMHJLZ HYL  [OPJR 7,; JVYL VU
from the other side of the non-skid pad
-HIYPJ ZJYLLUZ HYL  ë [OPJR ^P[O WLYPTL[LY
(F), then firmly press the screen assembly
L_[Y\KLK HS\TPU\T MYHTL L_[Y\KLK HS\TPU\T
downward to adhere the free end of the
IHZL MYHTL JHZ[ HS\TPU\T JSHTW IYHJRL[Z
bottom screen extrusion to the worksurface.
HUK JHZ[ HS\TPU\T IH`VUL[Z ;HJRHISL
MHIYPJ Z\YMHJLZ HYL  [OPJR 7,; JVYL VU
(A) 3AB408200 (B) 3AB1206*
(E) 7019440 (F) 3AB419700
DO NOT REMOVE THE OTHER SIDE
)PN ;HISL ^P[O /PUNLK (JJLZZ ;VWZ HUK
Big Table with Hinged Access Tops and
7HY[PHS +LW[O 0U[LYTLKPH[L :JYLLUZ
Partial Depth Intermediate Screens
)PN ;HISL ^P[O /PUNLK (JJLZZ ;VWZ HUK
7HY[PHS +LW[O 0U[LYTLKPH[L :JYLLUZ
(C) 3AB1207*
(G) 4A2200740
Antenna Workspaces
Antenna Workspaces
LP[OLY ZPKL VM ñ [OPJR WHY[PJSL IVHYK
10. Insert (2) ¼ - 20 x 3 / " black oxide machine
8
screws (E) into the holes under the rail clamp
3HTPUH[L ]LULLY HUK NSHZZ ZJYLLUZ HYL
(B). Hold the U-channel portion of the rail
ñ [OPJR MYHTLSLZZ ^P[O H  ë OPNO _ 
clamp (B) firmly against the side of the screen
ë ^PKL L_[Y\KLK HS\TPU\T IHZL MYHTL
bottom extrusion and tighten the screws
HUK JHZ[ HS\TPU\T JSHTW IYHJRL[Z
against the bottom of the worksurface.
LP[OLY ZPKL VM ñ [OPJR WHY[PJSL IVHYK
:WLJPMPJH[PVU 6W[PVUZ
NOTE: The ¼ - 20 x 3 / " black oxide machine
3HTPUH[L ]LULLY HUK NSHZZ ZJYLLUZ HYL
8
-VY MHIYPJ ZJYLLUZ ZWLJPM` ^P[O HU (U[LUUH
screws (E) are to be treated as set screws and
ñ [OPJR MYHTLSLZZ ^P[O H  ë OPNO _ 
HWWYV]LK [L_[PSL :WLJPM` WLYPTL[LY
will create the tight connection between the
ë ^PKL L_[Y\KLK HS\TPU\T IHZL MYHTL
MYHTL PU HU` 2UVSS *VYL WHPU[ MPUPZO
HUK JHZ[ HS\TPU\T JSHTW IYHJRL[Z screen bottom extrusion and the worksurface.
-VY MYHTLSLZZ ZJYLLUZ ZWLJPM` Z\YMHJL The rail clamp (B) must be seated firmly within
:WLJPMPJH[PVU 6W[PVUZ
[`WL! SHTPUH[L 3 VY ]LULLY = VY NSHZZ the side of the bottom extrusion, but should not
-VY MHIYPJ ZJYLLUZ ZWLJPM` ^P[O HU (U[LUUH
be pressed tight against the bottom of the
. MPUPZO PU HU` 2UVSS *VYL SHTPUH[L VY
HWWYV]LK [L_[PSL :WLJPM` WLYPTL[LY
worksurface. A space will remain between the
THYRLY Z\YMHJL 4 HU` *VYL ;LJO^VVK VY
MYHTL PU HU` 2UVSS *VYL WHPU[ MPUPZO
rail clamp and the bottom of the worksurface.
UH[\YHS ]LULLY VY *VYL NSHZZ MPUPZOLZ
-VY MYHTLSLZZ ZJYLLUZ ZWLJPM` Z\YMHJL
11. Position the openings in the underside
:WLJPM` IYHJRL[ PU HU` 2UVSS *VYL WHPU[ MPUPZO
[`WL! SHTPUH[L 3 VY ]LULLY = VY NSHZZ
of the screen over the bayonet mount
. MPUPZO PU HU` 2UVSS *VYL SHTPUH[L VY
brackets (A) and push the screen down
THYRLY Z\YMHJL 4 HU` *VYL ;LJO^VVK VY
until the screen is firmly seated.
UH[\YHS ]LULLY VY *VYL NSHZZ MPUPZOLZ
:WLJPM` IYHJRL[ PU HU` 2UVSS *VYL WHPU[ MPUPZO
(D) 7060440