Knoll Antenna Workspaces Installation Instructions Manual page 48

Big Table with Extension Top or Cabinet
Pattern Numbers Represented:
Connector Kit for Big Table Extension Tops,
Connector Kit for Above and Below Big Table
Extension Cabinets,
YBTE
End Leg for Dual Big Tables (Desk Height),
Starter Rails with End Caps,
YBRS_
Extended Rails,
YBRE_
Center Beam, YCB_
Flat Brackets, YBF
Fabric Inserts for Above Big Table
Extension Cabinets,
YSDXFB_
Parts List:
Horizontal Rail Cradle (A)
Cradle Clamp Bracket (B)
Spacer (C)
#12 X ¾" Black Wood Screw (D)
Center Beam Mounting Bracket (E)
Center Beam Mounting Bracket C-Clamp (F)
Spring Nut (G)
Flat Bracket (H)
¼-20 x 1" Machine Screw (I)
¼-20 x / " Machine Screw (J)
5
8
#14 x 1" FH Wood Screw (K)
M6 x 25mm Machine Screw (L)
Standard End Cap (M)
End Cap with Support Tab (N)
W-Bracket (O)
End Legs for Big Table
Intermediate Legs or Inset
Intermediate Legs for Big Table
Rails
Tops
Extension Top or Cabinet
Fabric Inserts
Tools Needed:
Drill
Phillips #2 and #3 bits
Rubber Mallet
Install Gauge
STEPS:
1. Complete steps 1-6 of the "Big Table
with Intermediate Leg" or steps 1-9 of
the "Big Table with Inset Intermediate
Leg" assembly instructions.
2. Slide two pairs of extended rails into the other
side of the cradles on the intermediate leg
assembly. Starter rails and extended rails
should meet in the center of each cradle
on the intermediate leg assembly. Adjust
the leg assembly position accordingly until
this alignment is met. (See Linked Desk
section for starter rail/ extended rail cradle
alignment detail). Repeat step 2 for all
desktop positions. For the table side that
is to be extended, the outer edge of the
cradles (A) should be inset 12" from the
(A) 3AB4004*
YBTE
YELDD_
(E) 3AB4061*
(I) 7194140
(M) 3AB4000*
end of the rails. Use gauge to help properly
position legs. See Install Gauge Guidelines.
: Rails for extension tops or cabinets
NOTE
are typically 12" wider than the desk top.
i.e.: 72" wide tops use 84" wide rails.
Install end caps with support tabs (N)
into the ends of the extended rails with
a rubber mallet. Tighten the screws (J)
in all the cradle clamp brackets (B).
3. Place center beams on center mounting
brackets (E) and place spring nuts (G) in the
bottom slot of the center beam. Locate each
spring nut (G) directly above the hole in the
center mounting bracket (E) and attach using
(1) M6 x 25mm machine screw (L) per nut.
(B) 3AB4007* (C) 3AB401252
(F) 3AB4062* (G) 3AB402196
(J) 7189140 (K) 7434100
(O) 3AB4095*
(N) 3AB4014*
NOTE:
lengths are slightly undersized (0.030"-0.040")
relative to Table Tops. This is intended to
ensure no or minimal spacing between
table tops on a Big Table run and should
translate into slight gaps between center
beams. Efforts should be made to balance
these gaps across Big Table runs.
4. Slide center beam mounting bracket C-clamps
(F), (2) per center beam mounting bracket (E),
into slots on center beam, pushing the C-clamps
tightly against the mounting brackets (E).
5. If applicable, attach suspended storage,
returns and/or electrical components at this
time. (see suspended storage, big table with
return and electrical installation instructions)
(D) 7196440
(H) 3AB4074115
(L) 3AB405540
Big Table Center Beams nominal