Knoll Antenna Workspaces Installation Instructions Manual page 67

12" Deep Big Table Cable Basket and 6" Deep
Data Cable Basket
Pattern Numbers Represented:
Upper Cable Baskets,
YR1CB__B
Lower Cable Baskets,
YR1CB__H
Lower Cable Basket Mount Kit,
Cable Basket Extra Mount Kit,
YR1CBB4
Cable Basket Extension Kit,
YR1CBX2
Parts List for 12"D Cable Basket Installation:
Upper Cable Basket Bracket (A)
Lower Cable Basket Bracket (B)
Upper Rod Weldment (C)
Spring Nut (D)
M6 x 25mm Machine Screw (E)
/ -18 x ¾" Machine Screw (F)
5
16
M6 x 12mm Machine Screw (G)
Lower Rod Weldment (H)
12"D Cable Basket, 27" or 39" (J)
Additional Parts for 6"D Data Cable Basket Installation:
Lower Rod Weldment (H)
6"D Data Cable Basket, 69" (K)
Additional Parts for Direct Underdesk Mounting:
#14 x 1" FH Wood Screw (I)
Optional:
Cable Basket Extension Kit
Cable Basket Extra Mount Kit
Tools Needed:
Drill
Phillips #2 and #3 bits
STEPS:
12"D Cable Basket Installation Steps:
1. Insert (4) spring nuts (D) into the bottom slot
in the center beam (i.e. (2) per bracket).
2. Place (1) upper cable basket bracket (A)
and (1) lower cable basket bracket (B)
together, with the cable basket (J) between
them, on each end of the cable basket.
: The location of the brackets will be
NOTE
determined by the size of the table and the
location of any installed power harnesses.
3. Attach the upper and lower brackets
together using (2) / -18 x ¾" machine
5
16
screws (F) per bracket pairing.
4. Place an upper rod weldment (C) into the
counter sunk hole in the center of each upper
cable basket bracket (A). Fasten using a
18 x ¾" machine screw (F) from the bottom
of each lower cable basket bracket (B).
5. Position the entire basket assembly under
the center beam, aligning the holes in the
upper rod weldment (C) with the spring nuts
inserted into the beam in Step 1. Fasten
each side using (2) M6 x 12mm machine
screws (G) per upper rod weldment.
YR1CBH
Additional Steps for 6" Data Cable
Basket Installation:
6. Place (1) upper cable basket bracket (A) and
(1) lower cable basket bracket (B) together,
with the data cable basket (K) between them,
on each end of the data cable basket.
NOTE:
size of the data cable basket will be determined
by the size of the table. The data cable basket
is 69"W and may have to be field cut to fit
between desk legs or legs and storage.
7. Attach the upper and lower brackets
together using (2)
screws (F) per bracket pairing.
8. Place a lower rod weldment (H) into the counter
sunk hole in the center of each upper cable
/ -
5
16
basket bracket (A). Fasten using a
x ¾" machine screw (F) from the bottom
of each lower cable basket bracket (B).
9. Attach the lower rod weldments (H) to the lower
cable basket brackets (B) of the previously
installed 12"D cable basket (J) using (2)
x ¾" machine screws (F) per weldment.
(A) 3AB8016* (B) 3AB8017*
(E) 3AB405540 (F) 7060440
(I) 7434100 (J) 3AB801001115 (27" wide)
3AB801002115 (39" wide)
The location of the brackets and the final
/ -18 x ¾" machine
5
16
/ -18
5
16
(C) 3AB8018*
(G) 3AB406640
(K) 3AB801003115 (69" wide)
Alternate Steps For Direct Underdesk Mounting:
Please note that the 12" basket may be directly
mounted to the underside of any worksurface.
1. Follow Installation Steps 2 through
4 for a 12"D Cable basket.
2. Position the entire basket assembly under
the worksurface, as desired, and attach the
upper rod weldments (C) to the underside
of the worksurface with (2) #14 x 1" FH
wood screws (I) per upper rod weldment.
Additional Options:
Cable basket extension kits (YR1CBX2)
NOTE:
may be installed to extend the length of either
the upper rod weldments (C) or lower rod
weldments (H) by 1 ¾" for 12" or 6" cable baskets
by twisting them directly onto the rod before
attaching the cable basket brackets (A/B).
: When a single cable basket is cut into two
NOTE
smaller baskets, a cable basket extra mount kit
(YR1CBB4) provides duplicate hardware to attach
the second basket. See steps 1-5 for installation.
/ -18
5
16
(D) 3AB402196
(H) 3AB8019*