Wall Mounted Overhead Cabinet Sliding Doors - Knoll Antenna Workspaces Installation Instructions Manual

Overhead Sliding Door

Wall Mounted Overhead Cabinet Sliding Doors

Pattern Numbers Represented:
Parts List - Hardware
Sliding Door Set, YSSD___
reff_profiles_ii_d_13_b.eps
reff_profiles_ii_d_13_b.eps
(A) 6TP40330
Parts List:
Housing (A)
HOUSING
reff_profiles_ii_d_13_b.eps
Fastener (B)
reff_profiles_ii_d_13_b.eps
Guide (C)
(B) 6TP40335
at 50%
Running Gear (D)
(C) 6TP40331
Stopper (E)
FASTENER
Overhead Cabinet
(C) 6TP40333
at 50% Sliding Doors
(D) 6TP40332
Tools Needed:
GUIDE
Measuring Tape
/ " Diameter Drill
8
16
Square Drive Screw Driver
Sliding Door Pre-Assembly
1. (If not factory installed) Faten the housings
(A) to the back of doors into the factory
drilled pockets using fastener (B). (Fig. 2)
STEPS
3. At each end of the factory installed support
Sliding Door Pre-Assembly
2. (If not factory installed) Using a hammer,
(If not factory installed) Fasten the housings
1.
(A) to the back of doors into the factory
insert the press-fit guide(s) (C) into the
drilled pockets using fastener (B). (Fig. 2)
factory drilled hole(s) on the inside surface
2. (If not factory installed) Using a hammer, insert
the press-fit guide(s) (C) into the factory drilled
of the bottom shelf oriented with the flats
hole(s) on the inside surface of the bottom shelf
4. Once all the running gears are installed
oriented with the flats of the guide parallel to
of the guide parallel to the front edge of the
the front edge of the bottom shelf. (Fig. 3)
bottom shelf. (Fig. 3)
Fig. 1
C
Overhead Sliding Door
Parts List - Hardware
reff_profiles_ii_d_13_b.eps
(A) 6TP40330
Parts List - Hardware
reff_profiles_ii_d_13_b.eps
reff_profiles_ii_d_13_b.eps
reff_profiles_ii_d_13_b.eps
(A) 6TP40330
(B) 6TP40335
at 50%
HOUSING
(B) 6TP40335
(C) 6TP40333
at 50%
FASTENER
RUNNING GEAR
(C) 6TP40333
GUIDE
STOPPER
Sliding Door Pre-Assembly
1. (If not factory installed) Faten the housings
Sliding Door Pre-Assembly
1. (If not factory installed) Faten the housings
(A) to the back of doors into the factory
drilled pockets using fastener (B). (Fig. 2)
2. (If not factory installed) Using a hammer,
3. At each end of the factory installed
rail you will find a rectangular cut-out, using
2. (If not factory installed) Using a hammer,
support rail you will find a rectangular
cut-out, using this as an access point,
this as an access point, install all the
insert the press-fit guide(s) (C) into the
install all the running gears (D). (Fig. 4)
running gears (D). (Fig. 4)
factory drilled hole(s) on the inside surface
4. Once all the running gears are installed
onto the track(s), insert one stopper
of the bottom shelf oriented with the flats
(E) at each end. (Fig. 5A & 5B)
of the guide parallel to the front edge of the
onto the track(s), insert one stopper (E) at
bottom shelf. (Fig. 3)
each end. (Fig. 5A & 5B)
Parts List - Hardware
(A) 6TP40330
HOUSING
reff_profiles_ii_d_13_b.eps
reff_profiles_ii_d_13_b.eps
reff_profiles_ii_d_13_b.eps reff_profiles_ii_d_13_b.eps
(B) 6TP40335
HOUSING (A) 6TP40330 FASTENER (B) 6TP40335
reff_profiles_ii_d_13_b.eps
(C) 6TP40333
at 50%
FASTENER GUIDE
at 50%
GUIDE
(E) 6TP40332
Sliding Door Pre-Assembly
1. (If not factory installed) Faten the housings
(A) to the back of doors into the factory
drilled pockets using fastener (B). (Fig. 2)
(A) to the back of doors into the factory
drilled pockets using fastener (B). (Fig. 2) 2. (If not factory installed) Using a hammer,
insert the press-fit guide(s) (C) into the
factory drilled hole(s) on the inside surface
insert the press-fit guide(s) (C) into the of the bottom shelf oriented with the flats
factory drilled hole(s) on the inside surface
of the guide parallel to the front edge of the
of the bottom shelf oriented with the flats
bottom shelf. (Fig. 3)
of the guide parallel to the front edge of the
bottom shelf. (Fig. 3)
Fig. 1
Figure 1
C
B
reff_profiles_ii_d_13_
Reff Profiles
reff_profiles_ii_d_13_
reff_profiles_ii_d_13_
reff_profiles_ii_d_13_b.eps reff_profiles_ii_d_13_b.eps
reff_profiles_ii_d_13_b.eps
reff_profiles_ii_d_13_b.eps
at 50%
(C) 6TP40333
at 50%
at 50%
at 50%
at 50%
(C) 6TP40331
(C) 6TP40331
RUNNING GEAR
at 50%
Tools Needed
(D) 6TP40332
(D) 6TP40332
Measuring Tape
STOPPER
8/16" Diameter Drill
Square Drive Screw Driver
3. At each end of the fac
3. At each end of the factory installed s
rail you will find a rectangular cut-out
Sliding Door Installation
this as an access point, install all the
1. Line the bottom track on the
running gears (D). (Fig. 4)
Sliding Door Installation
door with the guides on the
1. Line the bottom track on the back of the
rotating the door up, align th
4. Once all the running ge
door with the guides on the bottom shelf,
4. Once all the running gears are installe
rotating the door up, align the running
gears with the housings and
gears with the housings and snap into
onto the track(s), insert one stopper (
place. Repeat this for each door. (Fig. 6)
place. Repeat this for each d
each end. (Fig. 5A & 5B)
2. (If required) The doors can be leveled using
the gear mechanism on the running gears
which provides
1
2. (If required) The doors can b
down for a total of ¼" adjustability. (Fig.7)
the gear mechanism on the
which provides 1/8" of adjus
down for a total of 1/4" adju
Fig. 1
Fig. 1
C
C
B
reff_profile
™ Installation
at 50%
at 50%
at 50% at 50%
(C) 6TP4033
(D) 6TP40331 RUNNING
at 50%
(D) 6TP4033
RUNNING GEAR
STOPPER
STOPPER
3. At each e
rail you w
this as an
rail you will find a recta
running g
this as an access poin
running gears (D). (Fig.
4. Once all t
onto the t
each end
onto the track(s), inser
each end. (Fig. 5A & 5
/ " of adjustment up and
8
Fig. 1
C
B
B
a