Knoll Antenna Workspaces Installation Instructions Manual page 20

Desk with Extension Top or Cabinet (With Legs Under Worksurface)
Pattern Numbers Represented:
Connector Kit for Desk Extension Tops,
Connector Kit for Above or Below Desk
Extension Cabinets,
YBCDE
Legs for Desks or Returns (Desk or Standing Height),
Starter Rails with End Caps,
YBRS_
Fabric Inserts for Above Desk Extension Cabinets,
Part List:
Horizontal Rail Cradle (A)
Cradle Clamp Bracket (B)
Spacer (C)
W-Bracket (D)
¼-20 x 1" Machine Screw (E)
¼-20 x / " Machine Screw (F)
5
8
#14 x 1" FH Wood Screw (G)
#12 X ¾" Black Wood Screw (H)
Standard End Cap (I)
End Cap with Support Tab (J)
Rails
Desk End Legs
Top
Fabric Inserts
Tools Needed:
Drill
Install Gauge
Phillips #2 and #3 bits
Rubber Mallet
:
STEPS
1. Attach desk cradles (A) to legs, (2) per leg, using
(2) ¼-20 x 1" machine screws (E) per cradle (A).
2. Attach (1) pair of horizontal rails to cradles
(A) by first fastening (2) cradle clamp
brackets (B) loosely to each cradle (A) using
(4) ¼-20 x / " machine screws (F). NOTE:
5
8
Rails are 12" longer than top width for extension
applications. ie: 72" wide tops use 84" wide
rails. Install (2) standard end caps (I) into the
ends of the rails not receiving an extension
top or cabinet with the rubber mallet. Slide
one end of each rail into the cradle/clamp
assemblies, with rail paint holes facing up and
toward the center of the table desk assembly.
NOTE : If a glass top is being used,
holes are to face down and toward
center of the table desk assembly.
Position the outer edge of the cradles (A)
4" from the end of the rail on the side of the
assembly that is not to be extended. For the
side that is to be extended, the outer edge of
the cradles (A) should be inset 12" from the end
of the rails. Use gauge to help properly position
legs. See Install Gauge Guidelines. Tighten the
screws (F) in the cradle clamp brackets (B).
A.) 3AB4004*
YBCDE
YEL__
YSDXFB_
D.) 3AB4095*
H.) 7196440
3. Attach other ends of the rails to the (2) cradles
(A) in the other leg assembly as noted in step 2.
4. If applicable, attach suspended storage,
returns, and/or electrical components at this
time. (see suspended storage, table desk with
return and electrical installation instructions).
5. Surfaces 48" wide and greater require a spacer
(C) for additional support. When necessary,
a spacer (C) should be placed between the
top of each rail and the underside of the top,
centered on the width of the top. Spacers
(C) are attached to the top using (1) #12 X
¾" black wood screw (H) per spacer.
6. Lay top on base assembly. Use gauge to
properly position top. See Install Gauge
Guidelines. Attach top using (2) #14 x 1"
FH wood screws (G) per cradle (A) into
predrilled holes in the underside of the top.
7. Secure main table desk top and extension top
or cabinet using W-brackets (D) and tabbed end
caps (J) included in connector kit YBCDE. Use
(4) #14 x 1" FH wood screws (G) per W-bracket,
and (1) #14 x 1" FH wood screw per end cap.
B.) 3AB4007*
E.) 7194140
3AB4004
3AB4040
I.) 3AB4000* Screw, Mach, FLP 1/4-20 X 1
3AB4011
C.) 3AB401252
F.) 7189140
Screw, SM, FLP 14 X 1 Type A CAD or Zinc
J.) 3AB4014*
7a. For extension top applications, attach
15" wide extension top using (4) #14 x
1" FH wood screws (G) per W-bracket.
Extended rail should be 4 ½" inset from
the outer edge of the extension top.
7b. For above desk extension cabinet applications,
place cabinet on top of rails with (4) #14
x 1" FH wood screws (G) per W-bracket.
Extended rail should be 4 ½" inset from
the outer edge of the extension cabinet.
7c. For below desk extension cabinet applications,
slide cabinet on rails and attach with (4) #14 x
1" FH wood screws (G) per W-bracket. The top
of this cabinet should be on an even plane with
the main top. Extended rail should be 4 ½" inset
from the outer edge of the extension cabinet.
8. Adjust glides as needed to level desk assembly.
OPTIONAL STEP FOR FABRIC INSERTS:
9. Remove paper backing from double sided
adhesive tape. Place fabric insert in the recess
behind the back of the extension cabinet,
pressing the four corners firmly to attach.
3AB4012
G.) 7434100
7434100