Knoll Antenna Workspaces Installation Instructions Manual page 16

Table Desk with Return (Flush Leg on Return)
Pattern Numbers Represented:
Legs for Table Desks (Desk Height),
Return Rails for Desk, YBRR_
Part List:
Table Desk Cradle (A)
Cradle Clamp Bracket (B)
Spacer (C)
Return Rail Hook Top Bracket (D)
Return Rail Clamp Bottom Bracket (E)
W-Bracket (F)
#12 X ¾" Black Wood Screw (G)
¼-20 x 1" Machine Screw (H)
¼-20 x / " Machine Screw (I)
5
8
#14 x 1" FH Wood Screw (J)
Rails
Table Desk End Leg
Return Top
Tools Needed:
Drill
Phillips #2 and #3 bits
Install Gauge
STEPS:
1. Build table desk assemblies (see table
desk assembly instructions).
2. Attach (2) table desk cradles (A) to the
table desk end leg that will be used
under the return top using (2) ¼-20 x 1"
machine screws (H) per cradle (A).
3. Attach 1 return rail (YBRR_ _) to each
cradle (A) by first fastening 2 cradle clamp
brackets (B) loosely to each cradle using
(4) ¼-20 x / " machine screws (I).
5
8
: Return rails are 3" longer than the return
NOTE
top width when connected to a 24"d main top.
Return rails are 6" longer than the return top
width when connected to a 27"d main top.
Return rails are 9" longer than the return top
width when connected to a 30"d main top.
Slide rail into cradle/clamp assembly
with rail paint holes facing up and toward
center of table desk assembly.
A.) 3AB4069*
YELS_ _
D.) 3AB4008*
3AB4008
G.) 7196440
: End of rail must be fully inserted
NOTE
against (not on top of) the "fins" at the back
of the cradle. No endcaps are required.
Tighten the screws (I) in cradle
clamp brackets (B).
4. Attach return rail hook top brackets
(D) to other end of each return rail.
5. Locate return rail hook top brackets (D)
perpendicular to and on top of main table
desk rail. Attach a return rail clamp bottom
bracket (E) with (1) ¼ -20 X 1" machine screw
(H) to each return rail hook top bracket
(D). Main table desk top may need to be
loosened to allow clamp to be installed.
6. If applicable, add suspended storage
units at this time. (see suspended
storage installation instructions)
7. Position a W-bracket (F) on each return rail
halfway under the main table desk top.
B.) 3AB4007*
3AB4069
E.) 3AB4009*
3AB4009
H.) 7194140
3AB4040
Screw, Mach, FLP 1/4-20 X 1
C.) 3AB401252
3AB4012
F.) 3AB4095*
3AB4011
I.) 7189140 J.) 7434100
Screw, SM, FLP 14 X 1 Type A CAD or Zinc
8. Surfaces 48" wide and greater require a spacer
(C) for additional support. When necessary, a
spacer (C) should be placed between the top
of each rail and the underside of the return
top, centered on the width of the return top.
Spacers (C) are attached to the return top using
(1) #12 X ¾" black wood screw (G) per spacer.
9. Lay return top on return rail/leg assembly. Use
gauge to properly position top. See Install
Gauge Guidelines. Attach return top using (2)
#14 x 1" FH wood screws (J) per cradle into pre-
drilled holes in the underside of the return top.
10. Secure main table desk top and return top
to return rail W-brackets, using (4) #14 x 1"
FH wood screws (J) per W-bracket (F).
11. Adjust glides as needed to level return.
7434100