Desk Supported By 28" High Template Storage - Knoll Antenna Workspaces Installation Instructions Manual

Desk Supported by 28" High Template Storage

Pattern Numbers Represented:
28"H Case or Worksurface Shelf Support
Adapters, YBATE28
Legs for Desks or Returns (Desk Height),
Starter Rails with End Caps, YBRS_
Parts List:
Table Desk Cradle (A)
Rail End Support Cradle (B)
Cradle Clamp Bracket (C)
Spacer (D)
#12 X ¾" Black Wood Screw (E)
W-Bracket (F)
¼-20 x 1" Machine Screw (G)
¼-20 x / " Machine Screw (H)
5
8
#14 x 1" FH Wood Screw (I)
Flat Bracket (J)
Table Desk End Leg
Rails
End Caps
Template Case with Shelf
Desk Top
Tools Needed:
Drill
Phillips #2 and #3 bits
STEPS
1. Confirm position of supportive shelf
in previously installed Template
unit. The top surface of the shelf
should be positioned at 28 ½".
2. Attach (2) table desk cradles (A) to the
table desk end leg using (2) ¼-20 x 1"
machine screws (G) per cradle (A).
3. Attach 1 rail (YBER_ _) to each cradle
(A) by first fastening 2 cradle clamp
brackets (C) loosely to each cradle using
(4) ¼-20 x / " machine screws (H).
5
8
Rails are 6" longer than the
NOTE:
desk top width when connected to
a supportive Template case.
For both rails, slide rail into cradle/clamp
assembly with rail paint holes facing up
and toward center of return assembly.
NOTE: End of rail must be fully
inserted against (not on top of) the
"fins" at the back of the cradle.
Tighten the screws (H) in the cradle clamp
brackets (C).
(A) 3AB4069*
YEL__
3AB4069
(E) 7196440
(I) 7434100
4. Insert (1) end cap onto the opposite
end of each rail with rubber mallet.
5. Fasten (1) rail end support cradle (B) under
the free end of each return rail with (2) cradle
clamp brackets (C) using (4) ¼-20 x
screws (H). The rail end support cradles
should be positioned at the ends of the rails.
Fully tighten the screws (H) in the
cradle clamp brackets (C).
6. Attach (2) flat brackets (J) halfway under the
supportive Template shelf using (2) #14 x 1"
FH wood screws (I) per flat bracket. This will
help support the worksurface/ leg assembly
for positioning purposes in the next steps.
7. Position the attached rail end support
cradles (B) under the supportive Template
shelf and place a W-bracket (F) on
each rail halfway under the shelf.
8. Attach the rail end support cradles to
the supportive shelf using (4) #14 x 1"
FH wood screws (I) per cradle.
9. If applicable, add suspended storage units at
this time. (See suspended storage installation
instructions.)
(B) 3AB4015* (C) 3AB4007*
(F) 3AB4095* (G) 7194140
(J) 3AB4074115
10. Surfaces 48" wide and greater require a spacer
(D) for additional support. When necessary,
a spacer (D) should be placed between the
top of each rail and the underside of the desk
top, centered on the width of the desk top.
/ " machine
5
8
Spacers (D) are attached to the desk top using
(1) #12 X ¾" black wood screw (E) per spacer.
11. Lay desk top on rail/leg assembly. Use gauge
to properly position top. See Install Gauge
Guidelines. Attach desk top using (2) #14 x 1"
FH wood screws (I) per cradle into pre-drilled
holes in the underside of the desk top.
12. Secure supportive shelf and desk top
to rail W-brackets, using (4) #14 x 1"
FH wood screws (I) per W-bracket.
13. Complete the top to shelf connection by
securing the (2) flat brackets (J), installed in step
6, under the top/shelf seam using (2) additional
#14 x 1" FH wood screws (I) per flat bracket.
14. Adjust the glides on the Template
case or the table desk end leg as
needed to level the assembly.
(D) 3AB401252
(H) 7189140