Knoll Antenna Workspaces Installation Instructions Manual page 40

*LU[LY ILHT [VW JHWZ MPSS [OL [VW JOHUULS
ZSV[ VM H JLU[LY ILHT ^OLU UV ZJYLLUZ HYL
WSHUULK >OLU \WTV\U[LK Z[VYHNL VY ZJYLLUZ
HYL TV\U[LK [V [OL JLU[LY ILHT [VW JHWZ JHU
Center Beam End Caps
IL [YPTTLK PU [OL MPLSK [V MP[ HYV\UK IYHJRL[Z
( M\SS LUK JHW PZ \ZLK [V JV]LY [OL L_WVZLK
LUK VM [OL JLU[LY ILHT ( WHY[PHS LUK JHW PZ
\ZLK [V JV]LY [OL SV^LY LUK VM [OL JLU[LY ILHT
Pattern Numbers Represented:
^OLU HU L_[LUZPVU [VW VY JHIPUL[ PZ ZWLJPMPLK
Full Height End Cap, YCBE
Partial Height End Cap, YBCPE
H[ [OL LUK VM H IPN [HISL *LU[LY ILHT [VW
JHWZ HUK LUK JHWZ HYL ZWLJPMPLK ZLWHYH[LS`
Parts List:
Full Height End Cap (A) or
4V\U[PUN IYHJRL[Z HUK Z[HUJOPVUZ MVY
Partial Height End Cap (B)
Z[VYHNL JHU[PSL]LY ZOLS]LZ HUK MSH[ ZJYLLU
#10 – 32 x ¼", Cup Point Black Set Screw (C)
TVUP[VY HYTZ T\Z[ IL ZWLJPMPLK ZLWHYH[LS`
Center Beam
Tools Needed:
3/32" Allen Wrench
STEPS
Note: A full end cap is used to cover the
exposed end of the center beam.
A partial end cap is used to cover the lower end
of the center beam when an extension top or
cabinet is specified at the end of a big table.
7HY[PHS ,UK *HW +L[HPS
-\SS ,UK *HW +L[HPS Full End Cap Detail
(A) 3AB406801*
)PN ;HISL :JYLLU
When using an end panel for dual or single
sided big tables, an end cap is not required.
1. Insert full or partial end cap (A or B) into the
end of the center beam. The vertical tabs
on the end cap are to be inserted into the
horizontal slots on the sides of the beam.
,UK *HW MVY *LU[LY )LHT
Partial End Cap Detail
77
*VUZ[Y\J[PVU
*LU[LY ILHT PZ HU HS\TPU\T L_[Y\ZPVU  ë
OPNO HUK  KLLW ;VW JHWZ HYL L_[Y\KLK
WSHZ[PJ ,UK JHWZ HYL JHZ[ HS\TPU\T
:WLJPMPJH[PVUZ 6W[PVUZ
*LU[LY ILHTZ LUK JHWZ HUK [VW
JV]LYZ HYL H]HPSHISL PU HU` 2UVSS JVYL
(B) 3AB406802*
+HYR 9LK VY :SH[L )S\L WHPU[ MPUPZO
HUK T\Z[ IL ZWLJPMPLK ZLWHYH[LS`
Big Table with Extension Tops
)PN ;HISL ^P[O ,_[LUZPVU ;VWZ
Big Table without Extension Tops
)PN ;HISL ^P[OV\[ ,_[LUZPVU ;VWZ
(C) 3AB4073
2. Insert (1) #10 – 32 x ¼", cup point black set
screw (C) into each of the vertical tabs on the
end cap (A or B). Secure the set screws against
the center beam, using a 3/32" Allen wrench.