Fabric Intermediate Screens- Full Depth For Use With Tops Without Hinged Access - Knoll Antenna Workspaces Installation Instructions Manual

Fabric Intermediate Screens- Full Depth for Use
with Tops without Hinged Access
Pattern Numbers Represented:
Fabric Intermediate Screens, YPSI__F
0U[LYTLKPH[L ZJYLLUZ HYL KLZPNULK
Parts List:
[V WSHU HU`^OLYL HSVUN (U[LUUH IPN
Bayonet Mount Bracket (A)
[HISLZ VY SPURLK KLZR JVUMPN\YH[PVUZ [V
Upholstered Intermediate Screen Rail Clamp (B) KLSPULH[L PUKP]PK\HS ^VYRZWHJLZ
/ -18 x ¾" Machine Screw (C)
5
16 0U[LYTLKPH[L ZJYLLUZ PUJS\KL H WHPU[LK
¼ - 20 x / " Black Oxide Machine Screw (D)
3
HS\TPU\T KLZR[VW TV\U[PUN IYHJRL[
8
Screen Bottom Extrusion
[OH[ Z\WWVY[Z MYHTLK [HJRHISL MHIYPJ VY
Screen
MYHTLSLZZ NSHZZ ]LULLY SHTPUH[L VY THYRLY
Z\YMHJL [V H OVYPaVU VM  VY  
Tools Needed:
0U[LYTLKPH[L ZJYLLUZ HYL H]HPSHISL
Drill
MVY [^V WSHUUPUN HWWSPJH[PVUZ! M\SS
Phillips #2 and #3 bits
KLW[O HUK OPUNLK HJJLZZ KLW[O
STEPS
1. Insert (2) bayonet mount brackets (A) into
the top of the screen bottom extrusion so
that the holes in the brackets align with
the two sets of holes in the extrusion.
2. Insert (4) / -18 x ¾" machine screws (C)
5
16
beneath the extrusion and firmly attach the (2)
bayonet mount brackets (A) to the extrusion.
3. Determine the desired screen position along
the width of the table, and position the screen
extrusion on the worksurface accordingly.
4. Hook (1) upholstered intermediate screen
rail clamp (B) behind the back edge of the
worksurface so that the clamp's u-channel is
above the worksurface and the two screw holes
7HY[PHS +LW[O 0U[LYTLKPH[L
are below the worksurface. Slide one end of
:JYLLU MVY <ZL ^P[O
the bottom screen extrusion onto the u-channel
/0UNLK (JJLZZ ;VWZ
portion to temporarily support the clamp.
-\SS +LW[O 0U[LYTLKPH[L
:JYLLU MVY <ZL ^P[O ;VWZ
>P[OV\[ /0UNLK (JJLZZ
Full Depth Intermediate Screen for Use
with Tops Without Hinged Access
Intermediate Screens
Planning and Specification Guidelines
-\SS KLW[O PU[LYTLKPH[L ZJYLLUZ JVYYLZWVUK
[V (U[LUUH [VW KLW[OZ        
  HUK H[[HJO ^P[O H JSHTW IYHJRL[ HYV\UK
[OL MYVU[ HUK IHJR LKNLZ VM [OL [VW
0U[LYTLKPH[L ZJYLLUZ MVY OPUNLK HJJLZZ [VWZ
      HYL SLZZ KLLW [OHU OPUNLK
[VWZ [V LUHISL M\SS \ZL VM OPUNL MLH[\YL ;OL`
H[[HJO ^P[O H JSHTW IYHJRL[ HYV\UK [OL MYVU[
LKNL VM [OL [VW HUK H UVUZRPK WHK VU [OL [VW
*VUZ[Y\J[PVU
-HIYPJ ZJYLLUZ HYL  ë [OPJR ^P[O WLYPTL[LY
L_[Y\KLK HS\TPU\T MYHTL L_[Y\KLK HS\TPU\T
IHZL MYHTL JHZ[ HS\TPU\T JSHTW IYHJRL[Z
HUK JHZ[ HS\TPU\T IH`VUL[Z ;HJRHISL
MHIYPJ Z\YMHJLZ HYL  [OPJR 7,; JVYL VU
5. Hook the second upholstered intermediate
screen rail clamp (B) on to the front edge
of the worksurface in a similar fashion,
sliding the u-channel portion into the other
end of the bottom screen extrusion.
6. Insert (2) ¼ - 20 x
screws (D) into the holes under the back rail
clamp (B). Hold the U-channel portion of the
rail clamp (B) firmly against the side of the
screen bottom extrusion and tighten the screws
against the bottom of the worksurface.
NOTE:
screws (D) are to be treated as set screws and
will create the tight connection between the
screen bottom extrusion and the worksurface.
The rail clamp (B) must be seated firmly within
the side of the bottom extrusion, but should not
be pressed tight against the bottom of the
worksurface. A space will remain between the
rail clamp and the bottom of the worksurface.
(A) 3AB408200 (B) 3AB1206*
/ " black oxide machine
3
8
The ¼ - 20 x 3 / " black oxide machine
8
)PN ;HISL ^P[O /PUNLK (JJLZZ ;VWZ HUK
7HY[PHS +LW[O 0U[LYTLKPH[L :JYLLUZ
3PURLK +LZRZ -\SS +LW[O
Linked Desks Full Depth
0U[LYTLKPH[L :JYLLUZ
Intermediate Screens
142
Antenna Workspaces
(C) 7060440
LP[OLY ZPKL VM ñ [OPJR WHY[PJSL IVHYK
3HTPUH[L ]LULLY HUK NSHZZ ZJYLLUZ HYL
ñ [OPJR MYHTLSLZZ ^P[O H  ë OPNO _ 
ë ^PKL L_[Y\KLK HS\TPU\T IHZL MYHTL
HUK JHZ[ HS\TPU\T JSHTW IYHJRL[Z
:WLJPMPJH[PVU 6W[PVUZ
-VY MHIYPJ ZJYLLUZ ZWLJPM` ^P[O HU (U[LUUH
HWWYV]LK [L_[PSL :WLJPM` WLYPTL[LY
MYHTL PU HU` 2UVSS *VYL WHPU[ MPUPZO
-VY MYHTLSLZZ ZJYLLUZ ZWLJPM` Z\YMHJL
[`WL! SHTPUH[L 3 VY ]LULLY = VY NSHZZ
. MPUPZO PU HU` 2UVSS *VYL SHTPUH[L VY
THYRLY Z\YMHJL 4 HU` *VYL ;LJO^VVK VY
UH[\YHS ]LULLY VY *VYL NSHZZ MPUPZOLZ
7. Repeat Step 6 with the second
:WLJPM` IYHJRL[ PU HU` 2UVSS *VYL WHPU[ MPUPZO
(front) rail clamp (B).
8. Position the openings in the underside
of the screen over the bayonet mount
brackets (A) and push the screen down
until the screen is firmly seated.
EUDFNHW GHWDLO
EUDFNHW GHWDLO
(D) 7019440