Knoll Antenna Workspaces Installation Instructions Manual page 29

Big Table with Inset Intermediate Leg
Pattern Numbers Represented:
End Leg for Dual Big Tables (Desk Height),
Inset Intermediate Leg for Dual Big Tables (Desk Height),
Starter Rails with End Caps, YBRS_
Extended Rails,
YBRE_
Center Beam,
YCB_
Flat Brackets,
YBF
Parts List:
Horizontal Rail Cradle (A)
Cradle Clamp Bracket (B)
Spacer (C)
#12 X ¾" Black Wood Screw (D)
Center Beam Mounting Bracket (E)
Center Beam Mounting Bracket C-Clamp (F)
Inset Cradle Adapter for Intermediate Leg (G)
Horizontal Rail Inset Intermediate Leg Cradle (H)
Spring Nut (I)
Flat Bracket (J)
¼-20 x 1" Machine Screw (K)
¼-20 x / " Machine Screw (L)
5
8
#14 x 1" FH Wood Screw (M)
M6 x 25mm Machine Screw (N)
5 / -18 x 1" Machine Screw (O)
16
End Legs for Big Table
Inset Intermediate Legs for Big Table
Center Beam
Rails
End Caps
Tops
STEPS:
1. Attach cradles (A) to end legs, (4) per leg, using
(2) ¼-20 x 1" machine screws (K) per cradle (A).
2. Attach (1) center beam mounting bracket
(E) to middle of each end leg using (1) ¼-20
x 1" machine screw (K) per bracket (E).
3. Fasten (2) cradle clamp brackets (B) loosely
to each cradle using (4) ¼-20 x
screws (L). Slide one end of each starter rail
into an end leg cradle/clamp assembly, with
rail paint holes facing up and toward the
center of the assembly. If glass tops are being
used, holes are to face down and toward
the center of the table desk assembly.
Starter rails are typically 3" shorter than
NOTE:
top width. i.e.: 72" wide tops use 69" wide rails.
4. Position the outer edge of each cradle (A)
4" from the ends of the rails. Use install
gauge to help properly position leg. See
Install Gauge Guidelines. Tighten the screws
(L) in the cradle clamp brackets (B).
5. Install (4) end caps into the outside ends
of the starter rails with a rubber mallet.
6. For each inset intermediate leg create (2) inset
cradle adaptor assemblies by first aligning
(2) inset cradle adapters (G) with (1) inset
intermediate leg cradle (H) per adapter (H).
The side of the inset intermediate leg cradle
(H) will sit tightly against the cradle adapter
Big Table
YELDD_
YILDD_
Tools Needed:
Drill
Phillips #2 and #3 bits
Rubber Mallet
Install Gauge
(G), enabling (4) pre-drilled holes to align.
Fasten the paired components together using
(4) / -18 x 1" machine screws (O) per pair.
5
16
7. Position the inset cradle adaptor assemblies,
(2) on each inset leg, so they align with the two
outermost inserts on the leg. Attach the bottom
clamp portion of each inset cradle adaptor
assembly to the inset leg with (2) ¼-20 x 1"
/ " machine
5
8
machine screws (K) per adapter assembly.
8. Attach (2) horizontal rail cradles (A) and
(2) center beam mounting brackets (E)
to inner portion of inset intermediate
legs, using (2) ¼-20 x 1" machine screws
(K) for each cradle and bracket.
9. Insert the free ends of the starter rails
into one side of the cradles (A) on the
inset intermediate leg assembly.
10. Slide two pairs of extended rails into the
other side of the cradles on the inset
intermediate leg assembly. Starter rails and
extended rails should meet in the center of
each cradle on the inset intermediate leg
assembly. Adjust the leg assembly position
accordingly until this alignment is met.
(See Linked Desk section for starter rail/
extended rail cradle alignment detail).
Repeat step 10 for all desktop positions,
using install gauge to properly position
outermost legs. See Install Gauge Guidelines
(A) 3AB4004* (B) 3AB4007*
(E) 3AB4061* (F) 3AB4062*
(I) 3AB402196 (J) 3AB4074115
(M) 7434100 (N) 3AB405540
(C) 3AB401252
(G) 3AB4071*
(K) 7194140
(O) 4AH400496
Extended rails are typically
NOTE:
the same length as a desk top. i.e.:
72" wide tops use 72" wide rails.
Horizontal rail cradles (A) mounted
NOTE:
to starter rails will be oriented to face
each other. Any additional horizontal rail
cradles (A) mounted to extended rails
will be oriented to face the starter rails.
See the Plan View of Big Table with Inset
Intermediate Leg diagram that follows.
Install end caps into the ends of the last pair
of extended rails with a rubber mallet. Tighten
the screws (L) in all cradle clamp brackets (B).
11. Place center beams on center mounting
brackets (E) and place spring nuts (I) in
bottom slot of center beam. Locate each
spring nut (I) directly above the hole in the
center mounting bracket (E) and attach using
(1) M6 x 25mm machine screw (N) per nut.
Big Table Center Beams nominal lengths
NOTE:
are slightly undersized (0.030"-0.040") relative
to Table Tops. This is intended to ensure no or
minimal spacing between table tops on a Big
Table run and should translate into slight gaps
between center beams. Efforts should be made
to balance these gaps across Big Table runs.
(D) 7196440
(H) 3AB4072*
(L) 7189140