Knoll Antenna Workspaces Installation Instructions Manual page 27

Linked Desks
Pattern Numbers Represented:
Legs for Desks or Returns (Desk or Standing
Height),
YEL__
Starter Rails with End Caps,
YBRS_
Extended Rails,
YBRE_
Flat Brackets,
YBF
Part List:
Horizontal Rail Cradle (A)
Cradle Clamp Bracket (B)
Spacer (C)
#12 X ¾" Black Wood Screw (D)
¼-20 x 1" Machine Screw (E)
¼-20 x / " Machine Screw (F)
5
8
#14 x 1" FH Wood Screw (G)
Flat Bracket (H)
Tops
Starter Rails
Extended Rails
Desk End Legs
End Caps
STEPS:
1. Attach horizontal rail cradles (A) to all
legs, (2) per leg, using (2) ¼-20 x 1"
machine screws (E) per cradle (A).
2. Attach (1) pair of starter rails to cradles in first
pair of end legs by first fastening (2) cradle
clamp brackets (B) loosely to each cradle using
(4) ¼-20 x / " machine screws (F). Slide one
5
8
end of each starter rail into a cradle/clamp
assembly, with rail paint holes facing up and
toward the center of the desk assembly. If glass
tops are being used, holes are to face down
and toward center of the table desk assembly
NOTE : Starter rails are typically 3" shorter
than top width. ie: 72" wide tops use 69"
wide rails. Position the outer edge of each
cradle (A) 4" from the end of the rail. Use
install gauge to help properly position this
outermost leg. See Install Gauge Guidelines.
Tighten the cradle clamp brackets (B).
3. Install (2) end caps into the ends of the starter
rails that are not being linked to the next desk
with a rubber mallet.
A.) 3AB4004*
E.) 7194140
Tools Needed:
Drill
Phillips #2 and #3 bits
Install Gauge
Screw, Mach, FLP 1/4-20 X 1
Rubber Mallet
4. Attach the ends of the rails without end caps to
another end leg cradle/clamp assembly. Then,
slide extended rails into this assembly. Starter
rails and extended rails should meet in the
center of the cradle. Adjust the leg assembly
position accordingly until this alignment is met.
Repeat step 4 for all desktop positions, using
install gauge to properly position outermost
legs. See Install Gauge Guidelines.
: Extended rails are typically
NOTE
the same length as a desk top. ie:
72" wide tops use 72" wide rails.
: Horizontal rail cradles (A) mounted
NOTE
to starter rails will be oriented to face each
other. Any additional horizontal rail cradles
(A) mounted to extended rails will be oriented
to face the starter rails. See the Triple Linked
Desks Plan View diagram that follows.
Tighten the screws (F) in all cradle clamp
brackets (B).
5. Install (2) end caps into the ends of the last
pair of extended rails with a rubber mallet.
Triple Linked Desks Plan View
3AB4004
F.) 7189140
3AB4040
B.) 3AB4007* C.) 3AB401252
3AB4012
G.) 7434100
7434100
Screw, SM, FLP 14 X 1 Type A CAD or Zinc
6. If applicable, attach suspended storage,
returns and/or electrical components at this
time. (see suspended storage, desk with
return and electrical installation instructions
7. Lay tops on base assembly. Use install
gauge to properly position tops. See Install
Gauge Guidelines. Attach tops using (2)
#14 x 1" FH wood screws (G) per cradle
(A). Secure (2) flat brackets (H) to each
top-to-top connection using (4) #14 x 1"
FH wood screws (G) per flat bracket.
8. Surfaces 48" wide and greater require a spacer
(C) for additional support. When necessary,
a spacer (C) should be placed between the
top of each rail and the underside of the top,
centered on the width of the top. Spacers
(C) are attached to the top using (1) #12 X
¾" black wood screw (D) per spacer.
9. Adjust glides as needed to level desk assembly.
D.) 7196440
H.) 3AB4074115