Big Table With 22"H Template End Support - Knoll Antenna Workspaces Installation Instructions Manual

Big Table with 22"H Template End Support

Pattern Numbers Represented:
Support Adapters for Big Table -
22"H Case, YBATBT22
Parts List:
Horizontal Rail Cradle (A)
Cradle Clamp Bracket (B)
Center Beam Mounting Bracket (C)
Center Beam Mounting Bracket C-Clamp (D)
Spring Slot Nut (E)
¼-20 x 1" Machine Screw (F)
¼-20 x / " Machine Screw (G)
5
8
#14 x 1" FH Wood Screw (H)
M6 X 25mm Machine Screw (I)
Big Table Leg Adapter Bar (J)
Center Beam
Rails
End Caps
Tops
Tools Needed:
Drill
Phillips #2 and #3 bits
Rubber Mallet
Install Gauge
STEPS
: These steps include instructions for the big
Note
table assembly as it relates to supportive 22"H
Template storage and the use of the YBATBT22
adapter. For additional assembly steps see Big
Table with Intermediate Leg instructions.
1. Attach (4) cradles (A) to the big table
leg adapter bar (J), using (2) ¼-20 x 1"
machine screws (F) per cradle (A).
2. Attach the center beam mounting bracket
(C) to the middle of the adapter bar (J)
using (1) ¼-20 x 1" machine screw (F).
3. Prepare end leg or intermediate leg
assemblies, as necessary, at this point. (See
Big Table Intermediate Leg instructions.)
4. Fasten (2) cradle clamp brackets (B) loosely
to each cradle using (4) ¼-20 x
screws (G). Slide one end of each rail into
the adapter bar/cradle/clamp assembly, with
rail paint holes facing up and toward the
center of the assembly. If glass tops are being
used, holes are to face down and toward
the center of the table desk assembly.
NOTE: Starter rails are typically 3" shorter than
top width. i.e.: 72" wide tops use 69" wide rails.
(A) 3AB4004*
(E) 3AB402196
(I) 3AB405540
5. Position the outer edge of the adapter cradles
approximately 12 ½" from the ends of the rails
(so the side of the top will align with the back
of the Template unit.) DO NOT TIGHTEN the
screws (G) in the cradle clamp brackets (B) yet.
6. Install (4) end caps into the outside ends
of the starter rails with a rubber mallet.
7. Rest the adapter bar/rail assembly on top of
the previously assembled and leveled Template
units, aligning the inside face of the adapter
bar with the front edge of the Template unit.
The ends of the rails should be 1 ½" from
the back edge of the Template unit.
Adjust the cradle positions on the rails
as necessary to achieve alignment
/ " machine
5 and then tighten the screws (G) in
8
the cradle clamp brackets (B).
8. Follow the steps on the Big Table Intermediate
Leg instructions for rail connection details
to any intermediate legs, end legs, and
additionally linked rails. Install end caps with a
rubber mallet on the opposite ends of the rails.
(B) 3AB4007*
3AB4004
(F) 7194140
3AB4040
Screw, Mach, FLP 1/4-20 X 1
(J) 3AB1167*
(C) 3AB4061*
(G) 7189140
Screw, SM, FLP 14 X 1 Type A CAD or Zinc
9. Place center beams on center mounting
brackets (C). The end of the center beam
should align with the back edge of the
Template unit. Place spring nuts (E) in bottom
slot of center beam. Locate each spring nut
(E) directly above the hole in each center
mounting bracket (C) and attach using (1)
M6 x25mm machine screw (I) per nut.
10. Slide center beam mounting bracket
C-clamps (D), (2) per center beam
mounting bracket (C), into slots on center
beam, pushing the C-clamps tightly
against the mounting brackets (C).
11. Using (4) #14 x 1" FH wood screws (H), attach
the adapter bar to the top of the Template unit.
12. Lay tops on base assembly. Use install
gauge to properly position tops. See Install
Gauge Guidelines. Attach tops using (2) #14
x 1" FH wood screws (H) per cradle (A).
13. Secure flat brackets and spacers, as
required. (See Big Table Intermediate Leg
instructions for recommendations.)
14. Install center beam end caps, as
needed, to finish beam ends. (See
Center Beam End Cap instructions.)
15. Adjust glides as needed to
level big table assembly.
(D) 3AB4062*
(H) 7434100
7434100