Auto-Tuning Errors - YASKAWA HV600 Installation & Startup

5.8

Auto-Tuning Errors

This table gives information about errors detected during Auto-Tuning. If the drive detects an Auto-Tuning error, the
keypad will show the error and the motor will coast to stop. The drive will not send notification signals for faults and
alarms when Auto-Tuning errors occur.
Two types of Auto-Tuning errors are: Endx and Erx. Endx identifies that Auto-Tuning has successfully completed
with calculation errors. Find and repair the cause of the error and do Auto-Tuning again, or set the motor parameters
manually. You can use the drive in the application if you cannot find the cause of the Endx error.
Erx identifies that Auto-Tuning was not successful. Find and repair the cause of the error and do Auto-Tuning again.
Code Name
End1 Excessive Rated Voltage Setting
Code Name
End2 Iron Core Saturation Coefficient
Code Name
End3 Rated Current Setting Alarm
Code Name
End4 Adjusted Slip Calculation Error
Code Name
End5 Resistance Tuning Error
Code Name
End6 Leakage Inductance Alarm
Code Name
End7 No-Load Current Alarm
Code Name
Er-01 Motor Data Error
YASKAWA TOEPYAIH6B01A HV600 AC Drive Narrow Bypass Installation & Startup
Causes
The torque reference was more than 20% during
Auto-Tuning or the no-load current that was
measured after Auto-Tuning is more than 80%.
Causes
The motor nameplate data entered during Auto-
Tuning is incorrect.
Causes
The rated current value is incorrect.
Causes
The Auto-Tuning results were not in the applicable
parameter setting range.
The motor rated slip that was measured after
Stationary Auto-Tuning was 0.2 Hz or lower.
The secondary resistor measurement results were not
in the applicable range.
Causes
The Auto-Tuning results of the Line-to-Line
Resistance were not in the applicable range.
Causes
The Auto-Tuning results were not in the applicable
parameter setting range.
Causes
The Auto-Tuning results of the motor no-load current
value were not in the applicable range.
Auto-Tuning results were less than 5% of the motor
rated current.
Causes
The motor nameplate data entered during Auto-
Tuning is incorrect.
The combination of the motor rated power and motor
rated current do not match.
The combination of the motor rated current that was
entered during Auto-Tuning and E2-03 [Motor No-
Load Current] do not match.
The combination of the setting values of Motor Base
Frequency and Motor Base Speed do not match.

5.8 Auto-Tuning Errors

Possible Solutions
• Make sure that the input motor nameplate data is correct.
• Do Auto-Tuning again and correctly set the motor nameplate
data.
• If you can uncouple the motor and load, remove the motor from
the machine and do Rotational Auto-Tuning again.
• If you cannot uncouple the motor and load, use the results from
Auto-Tuning.
Possible Solutions
• Make sure that the input motor nameplate data is correct.
• Do Auto-Tuning again and correctly set the motor nameplate
data.
Possible Solutions
Do Auto-Tuning again and set the correct rated current shown on the
motor nameplate.
Possible Solutions
• Make sure the input motor nameplate data is correct.
• Do Rotational Auto-Tuning again and correctly set the motor
nameplate data.
• If you cannot uncouple the motor and load, do Stationary Auto-
Tuning 2.
Possible Solutions
• Make sure that the input motor nameplate data is correct.
• Examine and repair damaged motor wiring.
Possible Solutions
Make sure that the input motor nameplate data is correct, and do
Auto-Tuning again.
Possible Solutions
Examine and repair damaged motor wiring.
Make sure that the input motor nameplate data is correct, and do
Auto-Tuning again.
Possible Solutions
• Make sure that the motor nameplate data is correct.
• Do Auto-Tuning again and correctly set the motor nameplate
data.
• Examine the combination of drive capacity and motor output.
• Do Auto-Tuning again, and correctly set the motor rated power
and motor rated current.
• Examine the motor rated current and the no-load current.
• Set E2-03 correctly.
• Do Auto-Tuning again, and correctly set the motor rated current.
Do Auto-Tuning again, and correctly set the Motor Base Frequency
and Motor Base Speed.
5
147