YASKAWA HV600 Installation & Startup page 202

7.8 H: Terminal Functions
Setting Value Function
AB Thrust Mode
AC Setpoint Not Maintained
B2 BAS Interlock
B8 Pump Fault
B9 Transducer Loss
BA PI Auxiliary Control Active
BB Differential Feedback
Exceeded
BC Sleep Active
BD
Start Delay
BE
Pre-Charge
C0 HAND Mode
C1 AUTO Mode
C2 OFF Mode
C3 Main Feedback Lost
C4 Backup Feedback Lost
100 !During Run
101 !Zero Speed
102 !Speed Agree 1
103 !User-Set Speed Agree 1
104 !Frequency Detection 1
105 !Frequency Detection 2
106 !Drive Ready
202
The terminal activates when the output frequency is between 0.0 Hz and the value set in Y4-12 [Thrust Frequency] and the Thrust
Bearing function is active.
The terminal activates when the drive detects NMS [Setpoint Not Met] condition.
The terminal activates when the Run command is active or the drive is outputting the voltage. The drive will use this as an actuation
signal for an external damper.
The terminal activates when one of these faults is active: LFB [Low Feedback Sensed], HFB [High Feedback Sensed], NMS
[Setpoint Not Met], or EFx [External Fault (Terminal Sx)].
The terminal activates when the current into the analog input associated with PID feedback is more than 21 mA or less than 3 mA,
or an FDBKL [WIRE Break] Fault or an FDBKL [Feedback Loss Wire Break] Alarm is active.
The terminal activates when the PI Auxiliary Controller has an effect on the output speed.
The terminal activates when the difference between the PID Feedback and the value from the terminal set for H3-xx = 2D
[Differential Feedback] is more than Y4-18 [Differential Level] for the time set in Y4-19 [Differential Lvl Detection Time].
The terminal activates when the Sleep function is active and the drive is not operating.
Note:
The terminal will not activate for Sleep Boost function.
The terminal activates when the Feedback is more than the start level or the Feedback is less than the Inverse PID and the start timer
is timing.
Note:
You must set Y1-04 [Sleep Wake-up Level] ≠ 0 and Y1-05 [Sleep Wake-up Level Delay Time] ≠ 0 to use this function.
The terminal activates when the drive is in Pre-Charge Mode.
The terminal activates when the drive is in HAND Mode operation.
The terminal activates when the drive is in AUTO Mode operation.
The terminal activates when the drive is in OFF Mode operation.
The terminal activates when the drive loses the main PID feedback.
The terminal activates when the drive loses the backup PID feedback.
The terminal deactivates when you input a Run command and when the drive is outputting voltage.
ON : Drive is stopping
OFF : Drive is running
The terminal deactivates when the output frequency < E1-09 [Minimum Output Frequency].
ON : Output frequency ≥ value of E1-09.
OFF : Output frequency < value of E1-09.
The terminal deactivates when the output frequency is in the range of the frequency reference ± L4-02 [Speed Agree Detection
Width].
Note:
The detection function operates in the two motor rotation directions.
ON : The output frequency does not align with the frequency reference although the drive is running.
OFF : The output frequency is in the range of "frequency reference ± L4-02".
The terminal deactivates when the output frequency is in the range of L4-01 [Speed Agree Detection Level] ± L4-02 [Speed Agree
Detection Width] and in the range of the frequency reference ± L4-02.
Note:
The detection function operates in the two motor rotation directions. The drive uses the L4-01 value as the forward/reverse
detection level.
ON : The output frequency is not in the range of "L4-01 ± L4-02" or the range of frequency reference ± L4-02.
OFF : The output frequency is in the range of "L4-01 ± L4-02" and the range of frequency reference ± L4-02.
The terminal activates when the output frequency > "L4-01 [Speed Agree Detection Level] + L4-02 [Speed Agree Detection Width]".
After the terminal activates, the terminal stays activated until the output frequency is at the value of L4-01.
Note:
The detection function operates in the two motor rotation directions. The drive uses the L4-01 value as the forward/reverse
detection level.
ON : The output frequency > "L4-01 + L4-02".
OFF : The output frequency < L4-01, or the output frequency ≤ "L4-01 + L4-02"
The terminal deactivates when the output frequency > L4-01 [Speed Agree Detection Level]. After the terminal deactivates, the
terminal stays deactivated until the output frequency is at the value of "L4-01 - L4-02 [Speed Agree Detection Width]".
Note:
The detection function operates in the two motor rotation directions. The drive uses the L4-01 value as the forward/reverse
detection level.
ON : The output frequency < "L4-01 - L4-02", or the output frequency ≤ L4-01
OFF : The output frequency > L4-01
The terminal deactivates when the drive is ready and running.
YASKAWA TOEPYAIH6B01A HV600 AC Drive Narrow Bypass Installation & Startup
Description