General Safety; General Safety Instructions; Notice On Safety; Users Definition - Barco F90 Service Manual

2. GENERAL SAFETY

2.1

General Safety Instructions

General Safety Instructions.
• The projector is Class 1 laser product that conforms with IEC EN 60825-1:2014. For Northern America, the projector is class
3R laser product up to throw ratio 2.33. The projector conforms with IEC 60825–1:2007, and with performance standards for
laser products under 21 CFR 1040, except with respect to those characteristics authorized by Variance Number 2016–V-0144
effective March 6, 2017
• This projector is Risk Group 2 (RG2) according to IEC EN 62471-5. This projector may become Risk Group 3 (RG3) when an
interchangeable lens with throw ratio greater than 3.15 is installed. For Northern America, installation requirements according
to Risk group 3 (RG3) must be followed when interchangeable lens with throw ratio greater than 2.33 is installed. Refer to the
manual for the lens list and throw ratio before operation. Such combination of projector and lens are intended for professional
use only, and are not intended for consumer use.
• For RG3, no direct exposure to the beam shall be permitted. For RG3, operators shall control access to the beam within the
hazard distance or install the product at a height that will prevent eye exposure within the hazard distance.
• This projector has a built-in Class 4 laser cluster. Disassembly or modification is very dangerous and should never be attempted.
• Any operation or adjustment not specifically instructed by the user's guide creates the risk of hazardous laser radiation expo-
sure.
• Do not open or disassemble the projector as this may cause damage by the exposure of laser radiation.
• Do not stare into beam when the projector is on. The bright light may result in permanent eye damage.
• Not following the prescribed control, adjustment or operation procedure may cause damage by the exposure of laser radiation.
• Before operating this equipment please read this manual thoroughly and retain it for future reference.
• Installation and preliminary adjustments should be performed by properly trained and qualified personnel.
• All warnings on the projector and in the documentation manuals should be adhered to.
• All instructions for operating and use of this equipment must be followed precisely.
• All local installation codes should be adhered to.
2.2

Notice on safety

Safety
This equipment is built in accordance with the requirements of the international safety standards IEC60950-1, as basis for National
safety regulation world wide. The safety standard covers information technology equipment including electrical business equipment
intended to operate in "normal" environments (offices and homes). This safety standard imposes important requirements on the
use of safety critical components, materials and insulation, in order to protect the user or operator against risk of electric shock and
energy hazard and having access to live parts. Safety standards also impose limits to the internal and external temperature rises,
radiation levels, mechanical stability and strength, enclosure construction and protection against the risk of fire. Simulated single
fault condition testing reduce the risk of hazards and contribute to ensure the safety of the equipment to the user even when the
equipment's normal operation fails..
2.3 Users Definition
Definition
Throughout this manual, the term SERVICE PERSONNEL refers to Barco authorized persons having appropriate technical training
and experience necessary to be knowledgeable of potential hazards to which they are exposed (including, but not limited to HIGH
VOLTAGE ELECTRIC and ELECTRONIC CIRCUITRY and HIGH BRIGHTNESS PROJECTORS) in performing a task, and of mea-
sures to minimize the potential risk to themselves or other persons. Only Barco authorized SERVICE PERSONNEL, knowledgeable
of such risks, are allowed to perform service functions inside the product enclosure. The term USER and OPERATOR refers to any
person other than SERVICE PERSONNEL. When an interchangeable lens with throw ratio above a certain level is installed, the
F90 series projector becomes RG3. Refer to the manual for the lens list and hazard distance before operation. Such combination
of projector and lens are intended for professional use only, and are not intended for consumer use.
FOR PROFESSIONALLY USE ONLY, means installation only can be carried out by BARCO AUTHORIZED PERSONNEL familiar
with potential hazards associated with high intensity light beams.
This product operates on mains voltage. Do not open products without first unplugging the power cord.
It is advised against operating the product with housing top off, as there is a risk of injury caused by high voltage elements, cuts
caused by glass fragments in the event of a ruptured lamp or UV radiation burns.
723–0016 F90 01/12/2017
2. General safety
7