gefran SIEIDrive LIFT AGy -L Instruction Manual page 234

LCD Display
P.063 V/f interm volt V/F intermediate voltage
P.064 V/f interm freq V/F intermediate frequency
P.080 Max output freq Maximum output frequency
P.081 Min output freq Minimum output frequency
P.100 Slip compensat Amount of slip compensation during motoring
P.101 Slip comp filter Time constant of slip compensation
P.102 Slip comp regen Amount of slip compensation during regeneration
P.120 Manual boost [%] Torque boost level
P.121 Boost factor src Boost level source
P.122 Auto boost en Automatic boost function enabling
P.140 Magn curr gain Magnetizing current regulator gain
P.160 Osc damping gain Damping gain
P.170 Spd ctrl P-gainL Speed loop proportional gain (low speed)
P.171 Spd ctrl I-gainL Speed loop integral gain (low speed)
P.172 Spd ctrl P-gainH Speed loop proportional gain (high speed)
P.173 Spd ctrl I-gainH Speed loop integral gain (high speed)
P.174 Spd gain thr L Speed loop gain scheduling low threshold
P.175 Spd gain thr H Speed loop gain scheduling high threshold
P.176 Spd PI High lim Speed regulator High limit
P.177 Spd PI Low lim Speed regulator Low limit
P.178 SpdPI lim FacSrc Speed regulator limits factor source
P.180 SW clamp enable Current clamp enable
P.181 Clamp alm HldOff Holf off time for current clamp alarm. Set to maximum (25.5s) to
disable the alarm
P.200 Ramp CurLim mode Enable current limitation during ramp
P.201 Accel curr limit Current limit in acceleration phase
P.202 En lim in steady Enable current limitation in steady state
P.203 Curr lim steady Current limit at constant speed
P.204 Curr ctrl P-gain Current limiter proportional gain
P.205 Curr ctrl I-gain Current limiter integral gain
P.206 Curr ctr feedfwd Current limiter feed-forward
P.207 Decel curr limit Current limit in deceleration phase
P.220 En DC link ctrl Stall prevention during dec.
for overvoltage
P.221 DC-lnk ctr Pgain DC link voltage limiter proportional gain
P.222 DC-lnk ctr Igain DC link voltage limiter integral gain
P.223 DC-link ctr FF DC link voltage limiter feed-forward
P.240 OverTorque mode Overtorque mode
P.241 OT curr lim thr Current limit for overtorque
P.242 OT level fac src Overtorque level factor source
P.243 OT signal delay Delay time for overtorque signaling
P.260 Motor OL prot en Enabling of motor overload protection
234
PARAMETER
DESCRIPTION
PICK LIST
LCD Selection Description
[0] Null Null
[1] Analog inp 1 Analog input 1
[2] Analog inp 2 Analog input 2
[3] Analog inp 3 Analog input 3
[0] Disable Automatic boost function
[1] Enable Automatic boost function enabled
[0] Null Null
[1] Analog inp 1 Analog input 1
[2] Analog inp 2 Analog input 2
[3] Analog inp 3 Analog input 3
[0] Disable
[1] Enable
[0] None
[1] PI Limitator
[2] Ramp freeze
[0] Disable
[1] Enable
[0] None None
[1] PI Limitator PI Limit regulator
[2] Ramp freeze On/Off Ramp
[0] No Alm,Chk on 0: Overtorque detection always
active and Over-torque alarm
disabled.
[1] No Alm,Chk ss 1: Overtorque detection in steady
state and Over-torque alarm
disabled.
[2] Alm always 2: Overtorque detection always
active and Over-torque alarm
enabled.
[3] Alm steady st 3: Overtorque detection in steady
state and Over-torque alarm
enabled.
[0] Null Null
[1] Analog inp 1 Analog input 1
[2] Analog inp 2 Analog input 2
[3] Analog inp 3 Analog input 3
[0] Disable
[1] Enable
190 0 P.061 V 1
25 1.0 P.062 Hz 0.1
110 0 110 % of 1
F.020
0.0 0.0 25.0 % of 0.1
F.020
50 0 250 % 1
0.3 0 10 sec 0.1
50 0 250 % 1
3 0 25 % of 1
P.061
0 0 3
0 0 1
0 0 100 % 0.1
10 0 100 1
2.0 0.0 100.0 % 0.1
1.0 0.0 100.0 % 0.1
2.0 0.0 100.0 % 0.1
1.0 0.0 100.0 % 0.1
0.0 0.0 F.020 Hz 0.1
0.0 0.0 F.020 Hz 0.1
10.0 0.0 100.0 % of 0.1
F.020
-10.0 -100.0 0.0 % of 0.1
F.020
0 0 3
1 0 1
5.0 0 25.5 s 0.1
0 0 2
(*) 20 (*) % of I
nom
0 0 1
(*) 20 (*) % of I 1
nom
10.0 0.1 100.0 %
30.0 0.0 100.0 % 0.1
0 0 250 % 1
(*) 20 (*) % of I 1
nom
0 0 2
3.0 0.1 100.0 % 0.1
10.0 0.0 100.0 % 0.1
0 0 250 % 1
0 0 3
110 20 200 % 1
0 0 3
0.1 0.1 25 sec 0.1
1 0 1
AGy -L
IPA
415
416
417
418
419
420
500
421
422
423
424
425
501
502
503
504
507
508
509
510
511
426
512
427
428
429
430
431
432
433
494
434
435
436
437
438
439
440
441
444