gefran SIEIDrive LIFT AGy -L Instruction Manual page 227

LCD Display
S.244 Deceleration 2 Linear deceleration with ramp set 2
S.245 Jerk dec end 2 Jerk applied at the end of a deceleration with ramp set 2
S.250 Cont close delay RUN contactor close delay
S.251 Magnet time Motor magnetization time
S.252 Brake open delay Brake contactor open delay
S.253 Smooth start dly Smooth start duration
S.254 DCBrake stp time Duration of 0Hz braking at stop
S.255 Brake close dly Brake contactor close delay
S.256 Cont open delay RUN contactor open delay
S.260 Lift stop mode Lift behavior at stop
S.300 Manual boost [%] Manual boost at low revolutions
S.301 Auto boost en Automatic boost function enabling
S.310 Slip compensat Amount of slip compensation during motoring
S.311 Slip comp regen Amount of slip compensation during regeneration
S.312 Slip comp filter Time constant of slip compensation
S.320 DC braking level Current level used during DC brake at start and stop
S.400 Control mode Drive control mode
S.401 Encoder ppr Pulses per revolution of the encoder in use
S.450 Spd ctrl P-gainL Speed loop Proportional gain
S.451 Spd ctrl I-gainL Speed loop Integral gain
S.452 Spd PI High lim Speed PI regulator output upper limit
S.453 Spd PI Low lim Speed PI regulator output lower limit
S.901 Save parameters Save parameters
I.000 Enable src Source of the Enable command of Lift Control Word
AGy -L
PARAMETER
DESCRIPTION
PICK LIST
LCD Selection Description
[0] Dcb at stop DC brake is performed after the
output frequency is below P.440
threshold
[1] Normal stop DC brake is not performed at
stop
[0] Disable
[1] Enable
[0] V/f OpenLoop Speed control without encoder
feedback
[1] V/f ClsdLoop Speed control with encoder
feedback
(1)
(2)
INTERFACE
[0] False The command is never active
[1] True The command is always active
[2] DI 1 The command comes from
DigInp1
[3] DI 2 The command comes from
DigInp2
[4] DI 3 The command comes from
DigInp3
[5] DI 4 The command comes from
DigInp4
2
0.60 0.01 5.00 0.01 332 (F.204)
m/s
3
1.00 0.01 10.00 0.01 350 (F.258)
m/s
0.20 0 10 s 0.01
1 0 10 s 0.01
0.20 0 10 s 0.01
0 0 10 s 0.01
1 0 10 s 0.01
0.20 0 10 s 0.01
0.20 0 10 s 0.01
1 0 1
3.0 0.0 25.0 % of S.100 0.1 421 (P.120)
0 0 1 423 (P.122)
50 0 250 % of 1 419 (P.100)
rated slip
50 0 250 % of 1 500 (P.102)
rated slip
0.3 0 10 s 0.1 420 (P.101)
75 0 100 % of d.950 1 449 (P.300)
0 0 1 498 (P.010)
1024 1 9999 1
2.0 0 100 % 0.1 503 (P.172)
1.0 0 100 % 0.1 504 (P.173)
10 0 100 % of F.020 0.1 509 (P.176)
-10 -100 0 % of F.020 0.1 510 (P.177)
(1) (1) (2)
2 0 25
IPA
1316
(A.080)
1317
(A.081)
1318
(A.082)
1319
(A.083)
1320
(A.084)
1321
(A.085)
1322
(A.086)
1350
(A.220)
151 (I.501)
800
(C.000)
100
227