Technical Characteristics - Nice Spin Series Instructions And Warnings For The Fitter

8) Technical characteristics

Nice S.p.a., in order to improve its products, reserves the right to modify their technical characteristics at any time without prior notice. In
any case, the manufacturer guarantees their functionality and fitness for the intended purposes.
All the technical characteristics refer to a room temperature of 20°C (±5°C)
Technical characteristics: SPIN
Model
Type
Pinion
Peak thrust
[corresponds to the force necessary to start
a leaf]
Nominal torque
[corresponds to the force necessary to keep
a leaf moving]
Speed under no load [corresponding to if
"High speed" is programmed]
Nominal torque speed [corresponds to if
"High speed" is programmed]
Maximum frequency of operating cycles
Maximum continuous operating time
Operating limits
SPIN Power supply
SPIN/V1 Power supply
Max. absorbed power
Reduced consumption in Stand-By
Insulation class
Emergency Power Supply
Courtesy light SPIN
Courtesy light SPIN /V1
FLASH Output
Maximum BLUEBUS output load
STOP Input
Step-by-step Input
Radio AERIAL Input
Radio receiver
Programmable functions
Recognition functions
Operating temperature
Use in acid, saline or potentially explosive
atmosphere
Protection class
Dimensions / weight
SN6021
Electromechanical gearmotor for the automatic movement of garage doors for residential
use, complete with electronic control unit
Diameter 9.5mm, 28 teeth; for guides SNA5, SNA6 and guides supplied with SPIN20KCE,
SPIN30 and SPIN40
11.7Nm
[650N]
5.85Nm
[345N]
The control unit enables programming of 4 speeds equal to approx. 100%-85%-70%-55%
50 cycles per day (the control unit allows up to the maximum described in tables 4 and 5)
3 minutes (the control unit limits the continuous operation up to the maximum described in
tables 4 and 5)
Normally SPIN can automate sectional or overhead doors which remain within the dimen-
sions stated in table 3 and limits specified in tables 4 and 5.
250W
---
1 (a safety grounding system is required)
---
12V-21W socket BA15
12V-21W socket BA15
If programmed as "SPA "Open door indicator"": output for a maximum 24V-5W lamp;
if programmed as "Flashing light": output for 1 LUCYB Flashing light (12V, 21W); if pro-
grammed as "Electric lock": output for maximum 24V- 10W electro-mechanical lock;
if programmed as "Suction cup" output for maximum 24V- 10W electro-mechanical suc-
tion cup
2
For normally open contacts, for 8.2Kohm constant resistance, or normally closed contacts;
with self-recognition (any variation from the memorized status causes the "STOP" com-
mand
For normally open contacts (the closing of the contact causes the "STEP-BY-STEP" command)
52 ohm for RG58 or similar type of cable
"SM" connector for SMXI and SMXIS receivers
4 ON-OFF functions and 4 adjustable functions (see tables 15 and 17)
Recognition of the devices connected up to the BlueBUS output. Recognition of the type
of "STOP" device (Normally Open or Normally Closed contact or 8.2KΩ resistance).
Recognition of the door opening and closing positions and calculation of the slowdown
and partial opening points.
IP40 (use only in indoor or protected environments)
311x327 h 105 / 3,6Kg
SN6031
11.7Nm
[650N]
5.85Nm
[345N]
106 rpm
[0,20m/s]
53 rpm
[0,08m/s]
230Vac (±10%) 50/60Hz.
120Vac (±10%) 50/60Hz.
250W
less than 2.2W
With PS124 accessory
230V-60W socket E27
120V-60W socket E27
6
-20°C ÷ 50°C
No
SN6041
18Nm
[1000N]
9Nm
[560N]
370W
less than 2.5W
With PS124 accessory
230V-60W socket E27
120V-60W socket E27
6
311x327 h 105 / 4,7Kg
25
GB GB GB