Description Of The Electrical Connections; Final Checks And Start Up; Power Supply Connection - Nice Spin Series Instructions And Warnings For The Fitter

3.5) Description of the electrical connections

Here follows a brief description of the electrical connections. Please refer to the "7.3. Adding or Removing Devices" paragraph for further information.
FLASH: this output is programmable (see paragraph 7.2.4) for connection of one of the following devices:
Flashing light
If programmed as "flashing light" on the "FLASH" output a NICE "LUCY B" flashing light can be connected with a car type
12V 21W lamp.
During the manoeuvre the unit flashes at intervals of 0.5s.
"Door open indicator" Output
If programmed as "door open indicator" on the "FLASH" output a 24V max 5W indicator can be connected to signal when
the door is open.
It remains lit when the door is open and turns off when closed.
During the manoeuvre the indicator flashes slowly on opening and fast on closing.
Suction cup
If programmed as "suction cup" on the "FLASH" output a 24V max 10W suction cup can be connected (versions with
electromagnet only, without electronic devices).
When the door is closed, the suction cup is activated, locking the door. It is disabled during door opening and closing
manoeuvres.
Electric lock
If programmed as "electric lock" on the "FLASH" output an electric lock with latch 24V max 10W can be connected (ver-
sions with electromagnet only, without electronic devices).
During opening, the electric lock is activated for a brief interval to release the door and perform the manoeuvre.
During closing, ensure that the electric lock engages mechanically.
!
NEVER USE DEVICES OTHER THAN THOSE SPECIFIED
BLUEBUS: compatible devices can be connected up to this termi-
nal. They are connected in parallel using two conductors only,
through which both the electricity supply and the communication
signals travel. Please refer to paragraph "7.3.1BlueBUS" for further
information about BlueBUS.
STOP: input for the devices which block or eventually stop the
manoeuvre in progress. Contacts like "Normally Closed", "Normally
Open" or constant resistance devices can be connected up using
special procedures on the input. Please refer to Paragraph "7.3.2
STOP Input" for further information about STOP".

4) Final checks and start up

The manufacturers recommend you unhook the carriage and position the leaf at approximately half travel before starting the checking and
start up phase of the automation. This will ensure the leaf is free to move both during opening and closure.

4.1) Power supply connection

To power SPIN simply insert the plug in a mains socket. If necessary,
use a commercial adaptor if the plug on the SPIN unit does not cor-
respond to the socket available.
!
Never cut or remove the cable supplied with SPIN.
If not already available, the power socket for SPIN con-
nection must be fitted by skilled and qualified personnel
in strict observance of current legislation, standards and
regulations.
The power supply line must be protected from short cir-
cuits and ground leakage; a device must be provided to
enable the disconnection of the power supply during the
installation and maintenance of SPIN (the plug with outlet
are suitable for this purpose).
STEP-BY-STEP: input for devices which control movement. It is
possible to connect "Normally Open" devices up to this input. Acti-
vation of the control cord sends a signal to the PP input.
AERIAL: connection input for the radio receiver aerial (the aerial is
incorporated in LUCY B; alternatively an external antenna can be
used or leave a section of wire already present on the terminal, to
serve as an antenna.
As soon as SPIN is energized, you should check the following:
1. Make sure that the "BLUEBUS" LED flashes regularly, with about
one flash per second.
2. Make sure that the LED's on the photocells (if any) flash (both on
TX and RX); the type of flashing is not important as it depends on
other factors.
3. Make sure that the device connected to the FLASH output is off.
4. Make sure that the courtesy light is off.
If the above conditions are not satisfied, you should immediately
switch off the power supply to the control unit and check the electri-
cal connections more carefully.
Please refer to Chapter "7.6 Troubleshooting" for further information
about finding and analysing failures.
GB GB
11