Related Manuals for Nice E EDGE SI 228 LI ION
Summary of Contents for Nice E EDGE SI 228 LI ION
- Page 1 Nice E EDGE SI 228 LI ION Tubular Motor EN - Instructions and warnings for installation and use...
-
Page 2: Installation Warnings
GENERAL WARNINGS: SAFETY - INSTALLATION - USE (original instructions in Italian) ATTENTION Important safety instructions. Follow all instructions as improper installation may cause serious damage ATTENTION Important safety instructions. It is important for you to comply with these instructions for your own and other people’s safety. -
Page 3: Product Description And Intended Use
• it has a built-in radio receiver and control unit with encoder technology that elec- tronically controls the movement and precision of the limit switches; • it is compatible with all Nice control electronics using the NRC radio system (climate sensors and transmitters);... - Page 4 To select the limit switch gear wheel (fig. 3-a), drive 2.1 - Preliminary checks before installation and lim- wheel (fig. 3-b), motor bracket (fig. 3-f), refer to the “Nice Screen” catalogue, which itations on use is also available on www.niceforyou.com.
- Page 5 Gear wheel for limit switch Motor bracket (not included (not included in the pack- in the package). age). 2 screws: self-tapping without point, for plastic materials. Diameter: 4 mm; length of threaded part: = min. 5 mm - max 8 mm Supporting bracket of the winder roller (not included in the package).
-
Page 6: Programming And Adjustments
3.4 - Important warnings for memorising the radio transmitters • To select transmitter compatible with the motor’s receiver, refer to the “Nice Screen” catalogue, which is also available on www.niceforyou.com. • When no transmitter is yet present in the motor’s memory, memorise the FIRST TRANSMITTER with procedure A.1 only. - Page 7 –– GROUP “A” PROCEDURES –– Procedures which can only be completed with a Nice “ERA P” or “ERA W” transmitter with the s, n, t, PRG, ESC keys GENERAL WARNINGS RELATING TO THE PROCEDURES • Before starting any programming, move the awning to an intermediate position, away from the Up and Down limit switch- •...
- Page 8 A.2 - Temporarily deactivating (and reactivating) motors you do not wish to program NOTES AND WARNINGS • This procedure, which is useful for programming the limit switches of multiple channels without switching the motors off, temporarily locks out (for 5 minutes) only the motors that have both the limit switch positions (up and down) already programmed.
- Page 9 A.3.2 - To program the DOWN limit switch (“1”) continues (x 1) = 5 sec Command an DOWN movement Press and release count 2 movements. Hold down the but- release it after 5 count 2 movements. Hold down the button and wait... the button (1 time);...
- Page 10 “PRG” and “ESC” buttons (like “ERA P” and “ERA W” transmitters). • To run procedures A.5.1.B and A.5.2.B you must have a new transmitter to memorise, chosen from the “Nice Screen” catalogue , and an old previously memorised transmitter.
- Page 11 A.5.2.A - Procedure for transmitters equipped with the “PRG” and “ESC” buttons (“ERA P” and “ERA W”) continues = 5 sec sec. On the OLD transmitter: Hold count 2 movements; wait count 2 more move- release the but- On the NEW transmitter: hold down the but- down the button and wait...
- Page 12 A.6 - Memorisation of a climate sensor connected via radio NOTES AND WARNINGS • To run this procedure you need the climate sensor you want to memorise, chosen from the “Nice Screen” catalogue, and an old transmitter memorised in Mode I (see par. 3.4.1-A).
- Page 13 = 5 sec Hold down both buttons... release them after 5 count 5 movements. seconds; A.7.2 - Procedure run with a transmitter which has not yet been memorised NOTES AND WARNINGS • In order to carry out the following procedures, a transmitter with a PRG button should be used. A.7.2.A - Procedure run with a non-memorised transmitter using the button on the head of the motor = 7 sec Run procedure...
- Page 14 4 = 5 sec sec. After about 7 seconds, the motor performs a num- Hold down the button and release it after 5 count 3 movements. ber of movements equal to the number of pulses seconds; entered. (*) – IMPORTANT - After programming the option, or after the battery has discharged completely, it is imperative to immediately run 2 complete manoeuvre cycles (up and down = 1 cycle) to activate the function.
- Page 15 A.9 - Adjusting the awning’s cruise speed NOTES AND WARNINGS • For the values of the five options (V1=minimum, V2, V3=nominal, V4, V5=maximum speed), see “Technical characteristics”. • To determine whether the option chosen for the cruise speed of the awning is compatible with the characteristics of the your awning (weight, roller dimensions, torque), refer to “Technical characteristics”.
- Page 16 5 = 5 sec sec. After about 7 seconds, the motor performs a num- Hold down the button; release it after 5 seconds; count 3 movements. ber of movements equal to the number of pulses entered. A.11 - Adjusting the total duration of the movement NOTES AND WARNINGS •...
- Page 17 climate condition... WARNINGS FOR NORMAL OPERATION TABLE B OF THE AUTOMATION over-threshold under-threshold • the awning • the awning makes 2 move- makes 2 move- 5.1 - Commanding the opening, closing and stop- ... if the user ments and re- ments and re- sends the com- mains in the...
- Page 18 Refer to the technical characteristics stated on the motor's nameplate. Note: • All technical specifications stated herein refer to an ambient temperature of 20° C (± 5° C). • Nice S.p.A. reserves the right to apply modifications to products What to do if...
- Page 19 English – 18...
- Page 20 Nice SpA Via Callalta, 1 31046 Oderzo TV Italy www.niceforyou.com info@niceforyou.com...