Advertisement
5.2.1 - Commanding the "H" position
In general, to command the partial opening/closing of the awning (or shutter), press
the key associated with the partial height during programming (for more information,
read the procedure C.3 or D.8). If the transmitter has only three keys and only one
"H" height is memorised, simultaneously press keys s and t to recall this height. If,
during the installation phase, the "H" position was not programmed, it will assume
the factory value corresponding to the point located between the UPPER and LOW-
ER limit switches.
5.2.2 - Commanding the "90%" and "10%" positions
Two additional partial positions are available (fig. 4), factory-set to the following val-
ues:
– "90%" position = 90% of the path completed before the 0-UPPER limit switch is
reached (90% of the awning rolled up);
– "10%" position = 10% of the path completed before the 0-UPPER limit switch is
reached (10% of the awning rolled up).
To recall the "90%" position, press buttons s+ n (UP + STOP).
To recall the "10%" position, press buttons t+ n (DOWN + STOP).
4
0
90%
10%
0
90%
0
90%
5.3 - The user can vary the awning position with a
transmitter equipped with a "slider" surface
It is equally important to be able to set the automation's stop position in relation to
the circumstances (sunshine, rain, etc.).
If the automation is controlled with a Nice transmitter equipped with a "slider" sur-
face (e.g. P1V, etc.), the stop position of the automation can be varied as follows: the
top of the "slider" moves the automation upwards (as far as the upper limit switch
position); the bottom of the "slider" moves the automation downwards (as far as the
lower limit switch).
5.4 - "Automatic limit switch update" function
Caution! – This function is only available if the limit switches have been programmed
with the Semiautomatic procedure (par. C.2 or D.7). This function cannot be disa-
bled.
In ordinary use, the function activates automatically during an Up movement, when
the awning collides with the box or other mechanical stop (Up limit switch "0"). On
each collision, the function measures the position of the Up limit switch and memo-
rises the new value in place of the previous one. Over time, this compensates for
deformations in the structure due to wear and thermal cycles, so that the awning
always stops precisely at the Up limit position.
0
H
0
H
10%
0
H
10%
What to do if...
(troubleshooting guide)
q Powering an electrical phase, the motor does not move:
After excluding the possibility that thermal protection is active, in which case it is
sufficient to wait for the motor to cool down, make sure the mains voltage cor-
responds to the values indicated in the technical characteristics of this manual
by measuring the electricity between the "common" wire and the electrical phase
wire supplied with current. Finally, try to supply the opposite electrical phase.
q When sending a Raise command, the motor does not start:
This can happen if the awning/shutter is near the Upper limit switch ("0"). In this
case you must lower the awning/shutter a little bit and give the Raise command
again.
q The system operates in the emergency condition with an operator pre-
sent:
– Check to see if the motor has undergone a significant thermal or mechanical
shock.
– Make sure each part of the motor is still in good condition.
– Perform the deletion procedure (procedure A.4, B.4 or D.4) and adjust the limit
switches again.
Disposal of the product
As in installation operations, disposal operations must be performed by qualified
personnel at the end of the product's lifespan.
The product is made of various types of materials: some of them may be recycled,
while others must be scrapped. Find out about recycling and disposal systems in
use in your area for this product category.
Warning! – Some parts of the product may contain polluting or hazardous sub-
stances which, if released to the environment, may cause serious damage to the
environment or to human health.
As indicated by the symbol appearing here, the product may not be
disposed of with other household wastes. Separate the waste into cat-
egories for disposal, according to the methods established by current
legislation in your area, or return the product to the retailer when pur-
chasing a new version.
Warning! – Local legislation may impose heavy fines in the event of legal disposal
of this product.
The product's packaging materials must be disposed of in full compliance with local
regulations.
Technical Characteristics
n Frequency 433.92 MHz n Power emitted: 0 dBm n Radio coding: "BD".
Refer to the technical characteristics stated on the motor's nameplate.
Note: • All technical specifications stated herein refer to an ambient temperature of
20° C (± 5° C). • Nice S.p.A. reserves the right to apply modifications to products
at any time when deemed necessary, maintaining the same intended use and func-
tionality.
Simplified EU declaration of conformity
Hereby, NICE S.p.A., declares that the radio equipment type E FIT S 619 BD, E FIT
S 1014 BD, E FIT M 817 BD, E FIT M 1517 BD, E FIT M 3017 BD, E FIT M 4012
BD, E FIT M 5012 BD, E FIT L 5517 BD, E FIT L 6517 BD, E FIT L 7517 BD, E FIT
L 8012 BD, E FIT L 10012 BD, E FIT L 12012 BD, is in compliance with Directive
2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet
address: https://www.niceforyou.com/en/support.
COMPLIANCE WITH THE FCC RULES (PART 15) AND RSS-210 RULES
This device complies with Industry Canada's licence-exempt RSS-210s, and with
Part 15 of the FCC rules of the United States of America. Operation is subject to
the following two conditions: (1) this device may not cause interference; (2) this de-
vice must accept any interference, including interference that may cause undesired
operation of the device. Any changes or modifications made to this device, without
the express permission of the manufacturer, may void the user's authority to operate
this device.
English – 28
Advertisement
