Level One Programming (On-Off Functions); Level Two Functions (Adjustable Parameters); Level Two Programming (Adjustable Parameters) - Nice Spin Series Instructions And Warnings For The Fitter

7.2.2) Level one programming (ON-OFF functions)

Level 1 functions are all factory set to "OFF". However, they can be changed at any time as shown in Table 16. Follow the procedure care-
fully, as there is a maximum time of 10 seconds between pressing one key and another. If a longer period of time lapses, the procedure will
finish automatically and memorize the modifications made up to that stage.
Table N°16: changing ON-OFF functions
1. Press the key [Set] and hold it down (approx. 3 s)
2. Release the [Set] key when L1 LED starts flashing
3. Press keys [s] or [t] to move the flashing LED onto the LED representing the function
which is to be changed
4. Press the [Set] key to change function status
(short flash = OFF; long flash = ON)
5. Wait 10 seconds before leaving the programme to allow the maximum time to lapse
Note: Points 3 and 4 can be repeated during the same programming phases in order to set other functions to ON or OFF.

7.2.3) Level two functions (adjustable parameters)

Table 17: programmable function list: level two
Input LED Parameter
Pause Time
L1
Step-by-step
L2
Function.
Motor
L3
speed
L4
FLASH:
Note: " " represents the factory setting
All the parameters can be adjusted as required without any con-
traindication; only the selection of the device connected to the
"FLASH" output could require special care:

7.2.4) Level two programming (adjustable parameters)

The adjustable parameters are factory set as shown in the table 17 with "
18. Follow the procedure carefully as there is a maximum time of 10 seconds between pressing one key and another. If more time lapses,
the procedure will finish automatically and memorize the modifications made up to that stage.
Table 18: changing the adjustable parameters
1. Press the key [Set] and hold it down (approx. 3 s)
2. Release the [Set] key when L1 LED starts flashing
3. Press keys [s] or [t] to move the flashing LED to the "input LED"
which represents the parameter which is to be modified.
4. Press the key [Set],
and hold it down during step 5 and 6
5. Wait approx. 3 seconds, after which the LED representing the current level
of the parameter which is to be modified will light up.
6. Press keys [s] or [t] to move the LED which represents the parameter value.
7. Release the key [Set]
8. Wait 10s to exit programming on elapse of the maximum time interval.
Note: Points 3 to 7 can be repeated during the same programming phases in order to adjust other parameters
18
LED (level)
L1 10 seconds
L2 20 seconds
L3 40 seconds
L4 80 seconds
L1 Open – stop – close - stop
L2 Open - stop - close- open
L3 Condominium operation
L4 Man present
L1 Very slow
L2 Slow
L3 Medium
L4 Fast
L1 Output Open door indicator
L2 Flashing light
L3 Electric lock
L4 Suction cup
value
Adjusts the pause time, namely the time which
lapses before automatic closure. This will only
have an effect if automatic closing is active
Manages the sequence of controls associ-
ated to the Step-by-Step input or to the
1st radio command (see tables 7 and 8).
Adjusts the speed of the motor during nor-
mal travel.
Selects the device connected to the
FLASH output
!
Before connecting the device to the "FLASH" output,
ensure that the correct function has been programmed. Oth-
erwise there is a risk of damage to the device.
" However, they can be changed at any time, as shown in Table
Example
SET
3s
L1
SET
o
SET
10s
Description
Example
SET
3s
L1
SET
o
SET
o
SET
10s