Table of Contents
Advertisement
TABLE C – Motor head led signals
GREEN LED
Meaning
= at least 1 transmitter memorised and 2 limit positions
0 flashes
programmed.
= at least 1 transmitter memorised and 1 limit position
1 flash
programmed.
= at least 1 transmitter memorised and no limit posi-
2 flashes
tions programmed.
= no transmitter memorised (the limit switch status is
3 flashes
not shown by the led).
RED LED
Meaning
0 flashes
= no error.
= serious error - 1 (motor damaged - contact technical
steady on
service).
1 flash
= thermal protection function in progress.
= the last movement was automatically interrupted by
2 flashes
The "Obstacle detection" function.
3 flashes
= load too high relative to motor nameplate rating.
= the voltage supplied to the motor is less than 24 V
4 flashes
motor will still work, however the rated operating torque
is not guaranteed.
the voltage supplied to the motor is less than 24 V
5 flashes
motor will still work, however the rated operating torque
is not guaranteed.
6 flashes
= serious error - 4 (control circuit temperature too high).
7 flashes
= serious error - 5 (brake malfunction).
8 flashes
= serious error - 6 (brake malfunction).
9 flashes
= serious error - 7.
10 flashes
= serious error - 8.
11 flashes
= serious error - 9.
The motor repeats the report message on the status of the installation by performing
some brief movements when a movement is commanded. To understand the signifi-
cance of these movements read Table D.
TABLE D – Movement signals
No. of MOVEMENTS
Meaning
= at least 1 transmitter memorised and 2 limit positions
0 movements
programmed.
= no transmitter memorised (the limit switch status is
1 movement
not shown by the movements).
= at least 1 transmitter memorised and at least 1 limit
2 movements
position still to be programmed.
5 movements
= serious motor memory error.
21 – English
In general, to better identify the problem, refer to Table C (and D), section 5.10.
q Powering an electrical phase, the motor does not move:
After excluding the possibility that thermal protection is active, in which case it is
sufficient to wait for the motor to cool down, make sure the mains voltage corre-
sponds to the values indicated in the "technical data" chapter of this manual by
measuring the voltage between the "common" wire and the electrical phase wire
supplied with current. If the problem is still present, disconnect the power cord
from the motor (fig. 4-i) and connect it again.
q When an Up command is sent, the motor does not start:
This can happen if the awning is near the Upper limit switch ("0"). In this case you
must lower the awning a little bit and give the Raise command again.
q The system operates in the emergency condition with an operator pre-
sent (hold-to-run):
– Check to see if the motor has undergone a significant electrical or mechanical
shock.
– Make sure each part of the motor is still in good condition.
– Delete the UP ("0") and DOWN ("1") limit position and reprogram them.
. The
. The
As in installation, also at the end of product lifetime, the disassembly and scrapping
operations must be performed by qualified personnel.
This product comprises various types of materials: some may be recycled others
must be disposed of. Seek information on the recycling and disposal systems en-
visaged by the local regulations in your area for this product category. Caution! –
some parts of the product may contain pollutant or hazardous substances which, if
disposed of into the environment, may cause serious damage to the environment or
physical health. As indicated by the symbol on the left, disposal of this
product in domestic waste is strictly prohibited. Separate the waste into
categories for disposal, according to the methods envisaged by current
legislation in your area, or return the product to the retailer when pur-
chasing a new version. Caution! – Local legislation may envisage serious fines in the
event of abusive disposal of this product.
The packing materials of the product must be disposed of in compliance with local
regulations.
Technical Characteristics
Refer to the technical characteristics stated on the motor's nameplate.
Note: • All technical specifications stated herein refer to an ambient temperature of
20° C (± 5° C). • Nice S.p.A. reserves the right to apply modifications to products
at any time when deemed necessary, maintaining the same intended use and func-
tionality.
What to do if...
(troubleshooting guide)
Disposal of the product
Advertisement
Table of Contents
