Advertisement
Connection example
2
ERA W
ERA P
Transmitter
2.2 - Assembling and installing the tubular motor
Caution! – Read the safety warnings before proceeding. Incorrect installa-
tion could cause severe physical injury.
To assemble and install the motor, refer to fig. 3. Moreover, consult the Nice product
catalogue or go to www.niceforyou.com to choose the crown of the limit switch (fig.
3-a), the drag wheel (fig. 3-b), and the motor fastening bracket (fig. 3-f).
2.3 - Installation of accessories (optional)
After installing the motor, install the accessories, if required. In order to identify those
that are compatible and choose the models desired, see the Nice product cata-
logue, also viewable at www.niceforyou.com. Fig. 2 shows the type of accessories
that are compatible and their connection to the motor (all of these are options and
not included in the package).
3
ELECTRICAL CONNECTIONS AND
FIRST POWER UP
The electrical connections must be made only after installing the motor and compat-
ible accessories required.
The motor's power cable is already pre-wired and is fitted with a faston connector for
easily connecting the battery pack (Fig. 2).
3.1 - Connecting the motor to the battery pack
Use the dedicated faston connector (Fig. 2) to connect the motor to the battery
pack, while paying attention to the following warnings:
– improper connection can cause breakdowns and hazardous situations;
– scrupulously respect the connections indicated in this manual;
3.2 - Connection of accessories to motor
• Accessories can be connected by a radio (portable transmitters and climatic
sensor models with radio data transmission): memorise these accessories in the
motor during the programming phases; refer to the procedures given in this man-
ual and those given in the manuals supplied with the devices.
4
PROGRAMMING AND ADJUSTMENTS
4.1 - TWO-WAY and ONE-WAY operation
The motor can operate with both TWO-WAY and ONE-WAY transmission. The trans-
mission mode is determined by the first transmitter paired with the motor (ONE-WAY
or TWO-WAY).
3 – English
Solar Panel
Motor
Switch
If the motor is new (and has no remote control memorised), when it starts up it enters
the ONE-WAY mode, and thus can accept all one-way transmitters. If, within 15
seconds of start-up, no one-way transmitter is paired with it, the motor will make a
brief movement to signal that it has entered TWO-WAY mode, and will therefore only
be able to communicate with two-way transmitters from that time on.
WARNING: if the motor is new (and does not have any remote control mem-
orised), at the start-up run one of the memorisation procedures for the first
transmitter described at points B.1 motor configured for ONE-WAY commu-
nication, A.1 motor configured for TWO-WAY communication, or C.1 motor
configured for ONE-WAY communication and OLD generation transmitter
lacking the PRG and ESC buttons. In this way, the motor will be configured
in the TWO-WAY mode (and thus will be able to accept all two-way transmit-
ters) or ONE-WAY mode (and thus will be able to interact only with one-way
transmitters), depending on which transmitter is memorised first.
4.2 - Groups of programming and adjustment pro-
cedures
There are 4 groups of programming and adjustment procedures:
Group A – for motors
configured for TWO-WAY
communications
Group B – for motors
configured for ONE-WAY
communications.
Group C – for motors
configured for ONE-WAY
communication and using
a transmitter lacking the
PRG and ESC buttons.
Group D – QUICK pro-
gramming procedures
Battery Pack
BiDi
These procedures apply only when the
motor is configured for TWO-WAY com-
munications.
MONO
These procedures apply only when the
motor is configured for ONE-WAY com-
munications.
MONO
UP
STOP
DOWN
These procedures only apply when the
motor is configured for ONE-WAY com-
munication and a transmitter is used
that has the
▲
(UP),
■
(STOP) and
(DOWN) buttons, but lacks the PRG and
ESC buttons.
For information on these procedures, re-
fer to the quick guide supplied with the
product and available in digital format on
the website www.niceforyou.com.
▼
Advertisement
