Lennox Prodigy M2 Application Manual page 71

Control Parameter
No. Name Min.
Sup_HT_1_ 0
1.22
StgUp_Timer 0
Sup_HT_2_ 0
1.23
StgUp_Timer 0
0
1.24 StgDn_Timer
0
Heat Pump
1.25 0
Type
0
2.01 WmUp_Delay
0
0
2.02 BL_On_Delay
0
0
2.03 BL_Off_Delay
0
Max_HT_LT_
2.04 1
Occurrences
3
2.05 HT_Stg_Delay
12
Stg_Latch_
2.06 0
Option
0
2.07 StgUp_Timer
0
0
2.08 StgDn_Timer
0
0
3.01 WmUp_Delay
0
2
3.02 BL_On_Delay
8
20
3.03 BL_Off_Delay
80
Max_Ht_LT_
3.04 1
Occurrences
High_Fire_ 15
3.05
Delay 30
15
3.06 HT_Off_Delay
30
Max_CAI_
3.07 Proof_Switch_ 1
Occurrences
Max_Roll_Out_
Switch_
3.08 1
Occurrences
Max_GV_
3.09 Sense_ 1
Occurrences
Stg_Latch_ Op-
3.10 0
tion
0
3.11 StgUp_Timer
0
Control Value
Default Max.
Block 1 Heat Pump Heating Parameters (continued)
0 225
0 3600
0 225
0 3600
19 225
304 3600
0 1
Block 2 Electric Heating Parameters
112 255
3584 8160
0 0
0 0
5 75
20 300
3 15
3 15
12 60
0 1
57 225
912 3600
0 225
0 3600
Block 3 Gas Heating Parameters
112 255
3584 8160
10 15
40 60
30 75
120 300
3 15
15 150
30 300
50 150
100 300
3 6
1 4
3 6
0 1
57 225
912 3600
17. Electronic Configure To Order (ECTO) Control Parameters
Units Description
Supplemental heat stage 1 stage−up timer. The maximum time that
Counts
stage 1 runs before calling supplemental heat stage 1.
F:Sec
Used in zone sensor applications. Disabled if set to 0.
Supplemental heat stage 2 stage−up timer. The maximum time that
Counts
supplemental heat 1 runs before calling supplemental heat stage 2.
F:Sec.
Used in zone sensor applications. Disabled if set to 0.
Time delay before a lower stage turns off following a higher stage
Counts
termination.
F:Sec
Used in zone sensor applications.
0: Air Source Heat Pump
Option
1: Reserved
Counts Warm−up time delay. The time that the economizer is forced closed
D:Sec during warm−up (first occupied +heat demand)
Counts Blower on delay. The time before the blower turns on after a heating
B:Secs demand. Reserved for future use
Counts Blower off delay. The time the blower stays on after the heating de-
B:Secs mand is lost.
Service output activation. Maximum Primary and Secondary Limit
occurrences stored before service relay is energized. If max value
Counts
is set, service output is disabled. Note: Heating stage is not locked
out
Counts
Time delay between heat stages.
B:Secs
Stage latch option. Used in zone sensor applications.
0: Latch Disabled
Option
1: Latch Enabled
Stage up timer. The maximum time that lower stage runs before call-
Counts
ing next heat stage. Used in zone sensor applications. Disabled if set
F:Sec
to 0.
Time delay before a lower stage turns off following a higher stage
Counts
termination.
F: Sec
Used in zone sensor applications.
Counts Warm−up time delay. The time that the economizer is forced closed
D: Sec. during warm−up (first occupied + heat demand) .
Counts Blower on delay. The time before the blower turns on after a heating
B: Sec. demand.
Counts Blower off delay. The time the blower stays on after the heating demand
B:Sec. is lost.
Service relay activation. Maximum Primary and Secondary Limit
Counts occurrences stored before service relay is energized. If max value is
set, service output is disabled. Note: Heating stage is not locked out.
Counts
The minimum low fire time before high fire is allowed.
A:Sec.
Counts
Heating off delay.
A:Sec.
Service relay activation. Maximum Combustion Air Inducer proof
switch occurrences stored before service output is energized. If
Counts
max value is set, service output is disabled. Note: Heating stage is
not locked out.
Service output activation. Maximum Roll Out Switch occurrences
stored before service relay is energized. If max value is set, ser-
Counts
vice output disabled. Note: Heating stage is not locked out.
Service output activation. Maximum Gas Valve Sense occurrences
Counts stored before service output is energized. If max value is set, service
output is disabled. Note: Heating stage is not locked out.
Stage latch option. Used in zone sensor applications.
Option
0: Latch Disabled 1: Latch Enabled
Counts Stage−up timer. The maximum time that lower stage runs before calling
F: Sec next heat stage. Used in zone sensor applications. Disabled if set to 0.
Page 71
table continued on next page
PRODIGYT M2 UNIT CONTROLLER