Appendix C-2 Differences Of Buffer Memory - Mitsubishi Electric MELSEC-F Series User Manual

FX -1PG User's Manual
3U

Appendix C-2 Differences of Buffer Memory

BFM No.
High Low
order order
16bit 16bit
- #0
#2 #1
- #3
#5 #4
- #6
#8 #7
#10 #9
- #11
- #12
#14 #13
- #15
- #16
#18 #17
#20 #19
#22 #21
130
Item
Pulse rate 1 to 32,767 PLS/REV
Feed rate 1 to 2,147,483,647 (user unit)
b1, b0: System of units
b3, b2: Interrupt input setting
b5, b4: Position data multiplier
b6: Acceleration/deceleration mode
b7: Variable speed operation acceleration/
deceleration setting
b8: Pulse output format
Operation parameter
b9: Rotation direction
b10: Zero return direction
b11: Limit deceleration mode
b12: DOG input polarity
b13: Count start point
b14: STOP input polarity
b15: STOP input mode
1 to 2,147,483,647 (user unit)
Maximum speed Set the value within 1 to 200,000 Hz when
converted to pulse data.
0 to 32,767 (user unit)
Bias speed Set the value within 0 to 200,000 Hz when
converted to pulse data.
1 to 2,147,483,647 (user unit)
JOG speed Set the value within 1 to 200,000 Hz when
converted to pulse data.
1 to 2,147,483,647 (user unit)
Zero return speed
Set the value within 1 to 200,000 Hz when
(high speed)
converted to pulse data.
1 to 32,767 (user unit)
Zero return speed
Set the value within 1 to 200,000 Hz when
(creep)
converted to pulse data.
Number of zero-point
0 to 32,767
signal for zero return
-2,147,483,648 to 2,147,483,647 (user
unit)
Zero-point address Set the value within -2,147,483,648 to
2,147,483,647 PLS when converted to
pulse data.
Trapezoidal acceleration/deceleration:
1 to 32,767 ms
Acceleration/
Approximate
deceleration time
deceleration:
1 to 5,000 ms
Starting delay time 0 to 1,000 ms
-2,147,483,648 to 2,147,483,647 (user
unit)
Target address Ι Set the value within -2,147,483,648 to
2,147,483,647 PLS when converted to
pulse data.
1 to 2,147,483,647 (user unit)
Operation speed Ι Set the value within 1 to 200,000 Hz when
converted to pulse data.
-2,147,483,648 to 2,147,483,647 (user
unit)
Target address ΙΙ Set the value within -2,147,483,648 to
2,147,483,647 PLS when converted to
pulse data.
Appendix C: Differences with FX2N-1PG
Appendix C-2 Differences of Buffer Memory
Setting range
FX -1PG
3U
1 to 999,999 (user unit)
b3, b2: Not used
b6: Not used
b7: Not used
b11: Not used
1 to 153,000 (user unit)
Set the value within 10 to 100,000 Hz
when converted to pulse data.
0 to 15,300 (user unit)
Set the value within 0 to 10,000 Hz when
converted to pulse data.
1 to 153,000 (user unit)
Set the value within 10 to 100,000 Hz
when converted to pulse data.
1 to 153,000 (user unit)
Set the value within 10 to 100,000 Hz
when converted to pulse data.
1 to 15,300 (user unit)
Set the value within 0 to 10,000 Hz when
converted to pulse data.
-999,999 to 999,999 (user unit)
Set the value within -999,999 to 999,999
PLS when converted to pulse data.
Trapezoidal acceleration/deceleration:
S-shaped acceleration/
50 to 5,000 ms
Not used
-999,999 to 999,999 (user unit)
Set the value within -999,999 to 999,999
PLS when converted to pulse data.
1 to 153,000 (user unit)
Set the value within 10 to 100,000 Hz
when converted to pulse data.
-999,999 to 999,999 (user unit)
Set the value within -999,999 to 999,999
PLS when converted to pulse data.
FX -1PG
2N