Danfoss VLT AutomationDrive FC 302 Design Manual page 43

Specifications
®
VLT AutomationDrive FC 302
High/normal overload
(High overload=150% current during 60 s,
normal overload=110% current during 60 s)
Typical Shaft output at 525 V [kW]
Typical Shaft output at 575 V [hp]
Typical Shaft output at 690 V [kW]
Enclosure size
Output current (3-phase)
Continuous (at 525 V) [A]
Intermittent (60 s overload) (at 525 V)[A]
Continuous (at 575/690 V) [A]
Intermittent (60 s overload) (at 575/690 V) [A]
Continuous kVA (at 525 V) [kVA]
Continuous kVA (at 575 V) [kVA]
Continuous kVA (at 575/690 V) [kVA]
Maximum input current
Continuous (at 525 V) [A]
Continuous (at 575/690 V)
Maximum number and size of cables per phase
- Mains, motor, brake, and load share
2
[mm (AWG)]
Maximum external mains fuses [A]
Estimated power loss at 575 V [W]
Estimated power loss at 690 V [W]
3)
Efficiency
Output frequency [Hz]
Heat sink overtemperature trip [°C (°F)]
Control card overtemperature trip [°C (°F)]
Table 7.6 Electrical Data for Enclosures D2h/D4h/D7h/D8h, Mains Supply 3x525–690 V AC
1) For fuse ratings, see chapter 10.5 Fuses and Circuit Breakers.
2) Typical power loss is at normal conditions and expected to be within
values are based on a typical motor efficiency (IE/IE3 border line). Lower efficiency motors add to the power loss in the drive. Applies for
dimensioning of drive cooling. If the switching frequency is higher than the default setting, the power losses can increase. LCP and typical control
card power consumptions are included. For power loss data according to EN 50598-2, refer to drives.danfoss.com/knowledge-center/energy-
efficiency-directive/#/. Options and customer load can add up to 30 W to the losses, though usually a fully loaded control card and options for
slots A and B each add only 4 W.
3) Measured using 5 m (16.4 ft) shielded motor cables at rated load and rated frequency. Efficiency measured at nominal current. For energy
efficiency class, see chapter 10.11 Efficiency. For part load losses, see drives.danfoss.com/knowledge-center/energy-efficiency-directive/#/.
MG38C202
Design Guide
N160
HO NO
132 160
200 250
160 200
201 253
301 278
192 242
288 266
183 230
191 241
229 289
193 244
185 233
2x185 (2x350)
550
1)
2361 3074
2), 3)
2), 3) 2446 3175
0.98
0–590
110 (230)
80 (176)
Danfoss A/S © 01/2018 All rights reserved.
N200
HO NO HO
160 200 200
250 300 300
200 250 250
D2h/D4h/D7h/D8h
253 303 303
380 333 455
242 290 290
363 319 435
230 276 276
241 289 289
289 347 347
244 292 292
233 279 279
2x185 (2x350) 2x185 (2x350)
550
3012 3723 3642
3123 3851 3771
0.98
0–590
110 (230) 110 (230)
80 (176)
± 15% (tolerance relates to variety in voltage and cable conditions). These
N250 N315
NO HO NO
250 250 315
350 350 400
315 315 400
360 360 418
396 540 460
344 344 400
378 516 440
327 327 380
343 343 398
411 411 478
347 347 403
332 332 385
2x185 (2x350)
550 550
4465 4146 5028
4614 4258 5155
0.98 0.98
0–590 0–590
110 (230)
80 (176) 80 (176)
7 7
41