Danfoss VLT AutomationDrive FC 302 Design Manual page 39

Specifications
®
VLT AutomationDrive FC 302
High/normal overload
(High overload=150% current during 60 s, normal
overload=110% current during 60 s)
Typical shaft output at 400 V [kW]
Typical shaft output at 460 V [hp]
Typical shaft output at 500 V [kW]
Enclosure size
Output current (3-phase)
Continuous (at 400 V) [A]
Intermittent (60 s overload) (at 400 V)[A]
Continuous (at 460/500 V) [A]
Intermittent (60 s overload) (at 460/500 V) [kVA]
Continuous kVA (at 400 V) [kVA]
Continuous kVA (at 460 V) [kVA]
Continuous kVA (at 500 V) [kVA]
Maximum input current
Continuous (at 400 V) [A]
Continuous (at 460/500 V) [A]
Maximum number and size of cables per phase
- Mains, motor, brake, and load share [mm
Maximum external mains fuses [A]
Estimated power loss at 400 V [W]
Estimated power loss at 460 V [W]
3)
Efficiency
Output frequency [Hz]
Heat sink overtemperature trip [°C (°F)]
Control card overtemperature trip [°C (°F)]
Table 7.2 Electrical Data for Enclosures D2h/D4h/D7h/D8h, Mains Supply 3x380–500 V AC
1) For fuse ratings, see chapter 10.5 Fuses and Circuit Breakers.
2) Typical power loss is at normal conditions and expected to be within
values are based on a typical motor efficiency (IE/IE3 border line). Lower efficiency motors add to the power loss in the drive. Applies for
dimensioning of drive cooling. If the switching frequency is higher than the default setting, the power losses can increase. LCP and typical control
card power consumptions are included. For power loss data according to EN 50598-2, refer to drives.danfoss.com/knowledge-center/energy-
efficiency-directive/#/. Options and customer load can add up to 30 W to the losses, though usually a fully loaded control card and options for
slots A and B each add only 4 W.
3) Measured using 5 m (16.4 ft) shielded motor cables at rated load and rated frequency. Efficiency measured at nominal current. For energy
efficiency class, see chapter 10.11 Efficiency. For part load losses, see drives.danfoss.com/knowledge-center/energy-efficiency-directive/#/.
MG38C202
Design Guide
2 2x185 (2x350 mcm)
(AWG)]
1)
3093
2), 3)
2), 3) 2872
Danfoss A/S © 01/2018 All rights reserved.
N160 N200
HO NO HO
160 200 200
250 300 300
200 250 250
D2h/D4h/D7h/D8h
315 395 395
473 435 593
302 361 361
453 397 542
218 274 274
241 288 288
262 313 313
304 381 381
291 348 348
2x185 (2x350 mcm)
550 630
4116 4039
3569 3575
0.98 0.98
0–590 0–590
110 (230) 110 (230)
80 (176) 80 (176)
± 15% (tolerance relates to variety in voltage and cable conditions). These
N250
NO HO NO
250 250 315
350 350 450
315 315 355
480 480 588
528 720 647
443 443 535
487 665 589
333 333 407
353 353 426
384 384 463
463 463 567
427 427 516
2x185 (2x350 mcm)
800
5137 5005 6674
4566 4458 5714
0.98
0–590
110 (230)
80 (176)
37
7 7