Danfoss VLT AQUA Drive FC 202 Design Manual page 181

General Specifications and ...
High/normal load*
Typical shaft output at 550 V [kW]
Typical shaft output at 575 V [hp]
Typical shaft output at 690 V [kW]
Enclosure IP21, IP54 without/with options cabinet
Output current
Continuous (at 550 V) [A]
Intermittent (60 s overload) (at 550 V)[A]
Continuous (at 575/690 V) [A]
Intermittent (60 s overload) (at 575/690 V) [kVA]
Continuous kVA (at 550 V) [kVA]
Continuous kVA (at 575 V) [kVA]
Continuous kVA (at 690 V) [kVA]
Max. input current
Continuous (at 550 V) [A]
Continuous (at 575 V) [A]
Continuous (at 690 V) [A]
Max. cable size
Mains (mm 2 / AWG 2) )
2 2)
Motor (mm / AWG )
2 2)
Brake (mm / AWG )
Max. external mains fuses [A]
Estimated power loss at 600 V [W]
Estimated power loss at 690 V [W]
F12/F13 max. added losses A1 RFI or disconnect
Max. panel options losses
Weight, enclosure IP21, kg [lbs.]
Weight, enclosure IP54, kg [lbs.]
Weight, rectifier module, kg [lbs.]
Weight, inverter module, kg [lbs.]
4)
Efficiency
Output frequency [Hz]
Heatsink overtemp. trip [°C]
Power card ambient trip [°C]
*High overload=150% current for 60 s, Normal overload=110% current for 60 s.
Table 8.15 Technical Specifications F12/F13 12-Pulse, Mains Supply 6x525-690 V AC
1) For type of fuse, consult the Operating Instructions
2) American Wire Gauge
3) The typical power loss is at normal conditions and expected to be within ± 15% (tolerance relates to variety in voltage and cable conditions.)
These values are based on a typical motor efficiency (eff2/eff3 border line). Lower efficiency motors add to the power loss in the frequency
converter and the opposite is also true. If the switching frequency is raised from nominal, the power losses rise significantly. LCP and typical
control card power consumptions are included. Further options and customer load can add up to 30 W to the losses (though typically only 4 W
extra for a fully loaded control card or options for slot A or slot B, each)
4) Measured using 5 m screened motor cables at rated load and rated frequency
MG20Z202
Design Guide
HO
750
1050
900
988
1482
945
1418
941
941
1129
962
920
920
12062
3)
3) 12524
556
Danfoss A/S © Rev. 06/2014 All rights reserved.
P1M0 P1M2
NO HO
850 850
1150 1150
1000 1000
F12/F13
1108 1108
1219 1662
1060 1060
1166 1590
1056 1056
1056 1056
1267 1267
1079 1079
1032 1032
1032 1032
12x150 (12x300 mcm)
8x400 (8x900 mcm)
6x185 (6x350 mcm)
1600 2000
13731 13269
14250 13801
665 634
400
1260/1561 [2778/3441]
136 [300]
102 [225]
0.98
0–500
95 105
85
P1M4
NO HO NO
1000 1000 1100
1350 1350 1550
1200 1200 1400
1317 1317 1479
1449 1976 1627
1260 1260 1415
1386 1890 1557
1255 1255 1409
1255 1255 1409
1506 1506 1691
1282 1282 1440
1227 1227 1378
1227 1227 1378
2500
16190 16089 18536
16821 16719 19247
863 861 1044
1294/1595 [2853/3516]
136 [300]
95
8 8
179