Danfoss VLT AQUA Drive FC 202 Design Manual page 170

General Specifications and ...
High/normal load*
Typical shaft output at 400 V [kW]
Typical shaft output at 460 V [hp]
Enclosure IP21/IP54 with or without
options cabinet
Output current
Continuous (at 3x380-440 V) [A]
Intermittent (at 3x380-440 V) [A]
Continuous (at 3x441-480 V) [A]
Intermittent (at 3x441-480 V) [A]
Continuous kVA (at 400 V AC) [kVA]
Continuous kVA (at 460 V AC) [kVA]
Max. input current
Continuous (3x380-440 V) [A]
Continuous (3x441-480 V) [A]
Max. pre-fuses 1)
Max. cable size
2
Motor (mm /AWG
Mains, F1/F2 (mm
8 8
Mains, F3/F4 (mm
Loadshare (mm
2
Brake (mm /AWG
Estimated power loss at 400 V AC at
rated max load [W]
Estimated power loss at 460 V AC at
rated max load [W]
Max. added losses A1 RFI, CB or
disconnect, and contactor, F3/F4
Max. panel options losses
Weight, enclosure IP2, kg [lbs.]
Weight, enclosure IP54, kg [lbs.]
Weight, rectifier module, kg [lbs.]
Weight, inverter module, kg [lbs.]
4)
Efficiency
Output frequency [Hz]
Heatsink overtemp. trip [°C]
Power card ambient trip [°C]
*High overload=150% current for 60 s, Normal overload=110% current for 60 s
Table 8.3 Technical Specifications, F1-F4, Mains Supply 3x380-480 V AC
1) For type of fuse, consult the Operating Instructions.
2) American Wire Gauge.
3) The typical power loss is at normal conditions and expected to be within
These values are based on a typical motor efficiency (IE2/IE3 border line). Lower efficiency motors add to the power loss in the frequency
converter and the opposite is also true. If the switching frequency is raised from nominal, the power losses rise significantly. LCP and typical
control card power consumptions are included. Further options and customer load can add up to 30 W to the losses (though typically only 4 W
extra for a fully loaded control card or options for slot A or slot B, each).
4) Measured using 5 m screened motor cables at rated load and rated frequency.
5) Wiring terminals on N132, N160, and N315 frequency converters cannot receive cables one size larger.
168
P500
HO
450
600
800
1200
730
1095
554
582
779
711
[A]
2) 5)
)
2 /AWG 2) 5) )
2 /AWG 2) 5) )
2 2) 5)
/AWG )
2) 5)
)
9031
3)
8212
3)
893
102 [224]
102 [224]
Danfoss A/S © Rev. 06/2014 All rights reserved.
Design Guide
P560 P630
NO HO NO HO
500 500 560 560
650 650 750 750
F1/F3
880 880 990 990
968 1320 1089 1485
780 780 890 890
858 1170 979 1335
610 610 686 686
621 621 709 709
857 857 964 964
759 759 867 867
1600
8x150 (8x300 mcm)
8x240 (8x500 mcm)
8x456 (8x900 mcm)
4x120 (4x250 mcm)
4x185 (4x350 mcm)
10162 10146 11822 10649 12512
8876 8860 10424 9414
963 951 1054 978
1017/1318 [2242/2905]
102 [224] 102 [224]
102 [224] 102 [224]
± 15% (tolerance relates to variety in voltage and cable conditions.)
P710 P800
NO HO NO HO
630 630 710 710
900 900 1000 1000
1120 1120 1260 1260
1232 1680 1386 1890
1050 1050 1160 1160
1155 1575 1276 1740
776 776 873 873
837 837 924 924
1090 1090 1227 1227
1022 1022 1129 1129
2000
12x150 (12x300 mcm)
6x185 (6x350 mcm)
12490 14674 14244 17293 15466 19278
11595 11581 13213 13005 16229 14556 16624
1093 1092 1230 2067
400
1260/1561 [2778/3441]
102 [224] 136 [299]
136 [299] 102 [224]
0.98
0-590
95
75
P1M0
NO HO NO
800 800 1000
1200 1200 1350
F2/F4
1460 1460 1720
1606 2190 1892
1380 1380 1530
1518 2070 1683
1012 1012 1192
1100 1100 1219
1422 1422 1675
1344 1344 1490
2500
2280 2236 2541
136 [299]
102 [224]
MG20Z202