Danfoss VLT AQUA Drive FC 202 Design Manual page 176

General Specifications and ...
High/normal load*
Typical shaft output at 550 V [kW]
Typical shaft output at 575 V [hp]
Typical shaft output at 690 V [kW]
Enclosure IP21/IP54 with/without options cabinet
Output current
Continuous (at 550 V) [A]
Intermittent (60 s overload) (at 550 V)[A]
Continuous (at 575/690 V) [A]
Intermittent (60 s overload) (at 575/690 V) [kVA]
Continuous kVA (at 550 V) [kVA]
Continuous kVA (at 575 V) [kVA]
Continuous kVA (at 690 V) [kVA]
Max. input current
Continuous (at 550 V) [A]
Continuous (at 575 V) [A]
Continuous (at 690 V) [A]
Max. cable size
Motor (mm 2 /AWG
8 8
Mains, F2 (mm
Mains, F4 (mm
Loadshare (mm
Brake (mm 2 /AWG
Max. external mains fuses [A]
Estimated power loss at 575 V [W]
Estimated power loss at 690 V [W]
Max. added losses CB or disconnect and contactor,
F2/F4
Max. panel option losses
Weight, enclosure IP21, kg [lbs.]
Weight, enclosure IP54, kg [lbs.]
Weight, rectifier module, kg [lbs.]
Weight, inverter module, kg [lbs.]
Efficiency 4)
Output frequency [Hz]
Heatsink overtemp. trip [°C]
Power card ambient trip [°C]
*High overload=150% current for 60 s, Normal overload=110% current for 60 s.
Table 8.9 Technical Specifications, F2/F4, Mains Supply 3x525-690 V AC
1) For type of fuse, consult the Operating Instructions.
2) American Wire Gauge.
3) The typical power loss is at normal conditions and expected to be within
These values are based on a typical motor efficiency (IE2/IE3 border line). Lower efficiency motors add to the power loss in the frequency
converter and the opposite is also true. If the switching frequency is raised from nominal, the power losses rise significantly. LCP and typical
control card power consumptions are included. Further options and customer load can add up to 30 W to the losses (though typically only 4 W
extra for a fully loaded control card or options for slot A or slot B, each).
4) Measured using 5 m screened motor cables at rated load and rated frequency.
174
2) )
2 /AWG 2) )
2 2)
/AWG )
2 2)
/AWG )
2) )
3)
3)
Danfoss A/S © Rev. 06/2014 All rights reserved.
Design Guide
P1M0
HO NO
750 850
1050 1150
900 1000
988 1108
1482 1219
945 1060
1418 1166
941 1056
941 1056
1129 1267
962 1079
920 1032
920 1032
1600
12062 13731
12524 14250
556 665
1260/1561 [2778/3441]
102 [224]
95
± 15% (tolerance relates to variety in voltage and cable conditions.)
P1M2
HO NO HO
850 1000 1000
1150 1350 1350
1000 1200 1200
F2/F4
1108 1317 1317
1662 1449 1976
1060 1260 1260
1590 1386 1890
1056 1255 1255
1056 1255 1255
1267 1506 1506
1079 1282 1282
1032 1227 1227
1032 1227 1227
12x150 (12x300 mcm)
8x240 (8x500 mcm)
8x456 (8x900 mcm)
4x120 (4x250 mcm)
6x185 (6x350 mcm)
2000
13269 16190 16089
13801 16821 16719
634 863 861
400
1294/1595 [2852/3516]
136 [299]
0.98
0-500
105
85
P1M4
NO
1100
1550
1400
1479
1627
1415
1557
1409
1409
1691
1440
1378
1378
2500
18536
19247
1044
136 [299]
95
MG20Z202