Chrysler Concorde 1993 Service Manual page 290

8E - 8 INSTRUMENT PANEL AND GAUGES
TRACTION CONTROL SWITCH REMOVAL
(1) Remove upper center outlet bezel (Fig. 25 and
26).
(2) Press tabs at top and bottom of switch in bezel
and remove switch.
(3) For installation, reverse above procedures.
HEADLAMP SWITCH BEZEL REMOVAL
(1) Open front door and remove left end cover (Fig.
5, 25 and 26).
(2) Remove screw from left end of instrument
panel and pull bezel rearward to disengage clip(s).
(3) For installation, reverse above procedures.
HEADLAMP SWITCH REMOVAL
(1) Remove end cover and headlamp switch bezel
(Fig. 25 and 26).
(2) Remove three screws on headlamp switch and
pull out to disconnect two wiring connectors and re-
move.
(3) For installation, reverse above procedures.
Twist out lamp sockets are serviceable at this time.
HEADLAMP SWITCH TEST
(1) Remove instrument panel headlamp bezel (Fig.
25 and 26).
(2) Remove screw mounting headlamp switch mod-
ule and remove switch.
(3) Using an ohmmeter, test for continuity be-
tween the terminals of the switch as shown in the
Headlamp Switch Test (Fig. 27).
INSTRUMENT PANEL TOP COVER REMOVAL
(1) Pry-up each end of top cover disengaging clip
(Fig. 25 and 26).
(2) Lift rear edge of top cover using straight edge
along rear edge.
(3) Lift rear edge and slide top cover rearward dis-
engaging clips to remove cover.
(4) For installation, reverse above procedures.
INSTRUMENT PANEL END COVERS
REMOVAL—RIGHT AND LEFT
(1) Open the left door and pull on the outlet to re-
move end cover. Fuse Puller, Spare Fuses And Fuse
Diagram Are Located On Left End Cover. Fuse Ac-
cess Is Under Left End Cover (Fig. 25 and 26).
(2) Open right door and remove right end cover by
pulling from outlet bezel.
(3) For installation, reverse above procedures.
INSTRUMENT PANEL LOWER CENTER COVER
REMOVAL
Remove screw, on each side of center cover, and re-
move center cover. For installation, reverse above
procedures (Fig. 25 and 26).
RIGHT UPPER TRIM BEZEL REMOVAL
(1) Open front door and remove right end cover
(Fig. 25 and 26).
(2) Remove screw at end of instrument panel.
(3) Pull rearward to disengage four retaining clips.
May require a trim stick to pry-out inboard end of
bezel.
(4) For installation, reverse above procedures.
CENTER UPPER OUTLET BEZEL REMOVAL
(1) Pull center bezel rearward and disengage the
two retaining clips and disconnect electrical connec-
tor (Fig. 25 and 26).
(2) May require a tool to pry-out right end of bezel.
(3) For installation, reverse above procedures.
LOWER CENTER BEZEL REMOVAL
(1) Pull bezel straight rearward along the sides of
the radio and A/C control openings to disengage clips
(Fig. 23).
(2) For installation, reverse above procedures.
LEFT UNDER INSTRUMENT PANEL SILENCER/
DUCT REMOVAL
(1) Remove push-in fastener under left end of in-
strument panel (Fig. 25 and 26).
(2) Maneuver part off of brake bracket stud and
center floor distribution duct to remove.
(3) For installation, reverse above procedures.
RIGHT UNDER INSTRUMENT PANEL SILENCER/
DUCT REMOVAL
(1) Remove two push-in fasteners at center and left
end of silencer/duct (Fig. 25 and 26).
(2) Maneuver part off of center floor distribution
duct to remove.
(3) For installation, reverse above procedures.
WOOD GRAIN TRIM BEZEL REMOVAL—CHRYSLER
207
(1) Open right front door and remove right end
cover and center upper outlet bezel (Fig. 25 and 26).
(2) Remove screw at right end of instrument panel
and screw at center outlet opening.
(3) Remove wood grain bezel by pulling straight
rearward, disengaging the three clips.
(4) For installation, reverse above procedures.
RADIO REMOVAL
(1) Remove lower center bezel and remove two ra-
dio retaining screws and then remove radio (Fig. 23).
(2) Pull radio straight out and disconnect both
electrical connectors, antenna cable and remove
screw on radio ground strap, then remove radio.
(3) For installation, reverse above procedures.