4 INTRODUCTION INTRODUCTION When it comes to service, remember that your authorized Congratulations on selecting your new Chrysler Group dealer knows your vehicle best, has factory-trained tech- LLC vehicle. Be assured that it represents precision nicians and genuine Mopar parts, and cares about your workmanship, distinctive styling, and high quality - all satisfaction.
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against op- erating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Your vehicle uses a keyless ignition system. This system consists of a Key Fob with Remote Keyless Entry (RKE) transmitter and a Wireless Ignition Node (WIN) with integral ignition switch.
Page 13
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key Fob The Key Fob operates the ignition switch. It also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the RKE transmitter go dead.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Power window switches will also remain active Key-In-Ignition Reminder for up to 90 seconds after the ignition switch has been Opening the driver’s door when the Key Fob is in the turned to LOCK, depending upon the accessory delay ignition and the ignition switch position is LOCK or setting.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 vehicle can be used to start and operate the vehicle. The NOTE: The Sentry Key Immobilizer system is not system will shut the engine off in two seconds if an compatible with aftermarket remote starting systems. invalid Key Fob is used to start the engine.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE At the time of purchase, the original owner is provided General Information with a four-digit Personal Identification Number (PIN). The Sentry Key system complies with FCC rules Part 15 Keep the PIN in a secure location. This number is and with RSS-210 of Industry Canada.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 The engine will run only if a valid key is used to start the about 16 seconds to indicate that the alarm is being set. vehicle. After the alarm is set, the Vehicle Security Light will flash at a slower rate to indicate that the Vehicle Security Rearming Of The System Alarm is armed.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE disarm the Vehicle Security Alarm. If someone enters Tamper Alert the vehicle through the liftgate and opens any door the If something has triggered the Vehicle Security Alarm in alarm will sound. your absence, the horn will sound three times when you unlock the doors and the Vehicle Security Light will flash •...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 NOTE: RKE transmitter does not need to be pointed at the • The front courtesy overhead console and liftgate lights vehicle to activate the system. do not turn on if the dimmer control is in the interior NOTE: Inserting the Key Fob with RKE transmitter into lights ON position (extreme top position).
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Using the RKE Transmitter (optional), power sliding doors, Remote Start feature Three-button RKE transmitters will provide basic UN- (optional). Some features can be programmed to the LOCK, LOCK and PANIC functions. customers preferences. For example, flash headlights or sound horn on LOCK.
Page 21
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 • For vehicles not equipped with the EVIC, the Remote Remote Unlock Doors and Liftgate Press and release the UNLOCK button on the RKE Unlock feature can be enabled or disabled by perform- transmitter once to unlock the driver’s side or twice to ing the following steps: unlock all doors and liftgate.
Page 22
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Pressing the LOCK button on the RKE transmit- Sound Horn with Remote Lock ter while you are inside the vehicle will activate the This feature will cause the horn to chirp when the doors Vehicle Security Alarm.
Page 23
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 3. Release both buttons at the same time. headlights and park lights will flash, the horn will pulse on and off, and the interior lights will turn on. 4. Test the feature while outside of the vehicle by press- ing the LOCK button on the RKE transmitter with the The Panic Alarm will stay on for three minutes unless ignition switch in the LOCK position and the Key Fob...
Page 24
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the liftgate is locked and is not equipped with a Power Open/Close Right Power Sliding Door — If powered liftgate, pressing the LIFTGATE button twice Equipped will result in the liftgate becoming unlocked for 30 sec- Press the RIGHT Power Sliding Door button twice on the onds allowing you to manually access the liftgate area.
Page 25
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 • For vehicles not equipped with the EVIC, perform the NOTE: Pressing the LOCK button on the RKE transmit- following steps: ter while you are in the vehicle will activate the Vehicle Security Alarm.
Page 26
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Replacing the Transmitter Battery General Information The recommended replacement battery is one CR2032 This device complies with Part 15 of the FCC rules and battery. RSS 210 of Industry Canada. Operation is subject to the following conditions: NOTE: •...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 • Brake switch inactive (brake pedal not pressed) REMOTE STARTING SYSTEM — IF EQUIPPED This system uses the Remote Keyless Entry • Ignition key removed from ignition switch (RKE) transmitter to start the engine conve- •...
Page 28
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Enter Remote Start Mode To Enter the Vehicle After Remote Start Press and release the REMOTE START button To enter the vehicle while the engine is running during a on the RKE transmitter twice within five sec- Remote Start, you must first unlock the vehicle using the onds.
Page 29
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 • For vehicles equipped with the Electronic Vehicle To Turn Off the Engine While in Remote Start Information Center (EVIC), the message “Insert Key/ Mode Turn to ON” will flash in the EVIC until you insert the Press and release the REMOTE START button one time or Key Fob.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS If the lock plunger is down when you shut the door, the door will lock. Make sure the keys are not inside the Manual Door Locks vehicle before closing the door. Lock the doors by pushing down on the lock plungers on each door trim panel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • When leaving the vehicle, always remove the key from the ignition switch, and lock your vehicle.
Page 32
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE operate. A chime will sound if the Key Fob is in the If you press the power door lock switch while the sliding ignition switch and a door is open, as a reminder to door is open, the sliding door will lock.
Page 33
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 2. Fasten your seat belt. (Fastening the seat belt will The Lock Doors Automatically at 15 mph (24 km/h) cancel any chiming that may confuse you during this feature can be reactivated by repeating the above men- programming procedure.) tioned procedure or by performing the procedure in the EVIC (if equipped), Personal Settings (Customer-Pro-...
Page 34
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Settings (Customer-Programmable Features) in the 6. A single chime will sound to indicate the feature has “Electronic Vehicle Information Center (EVIC),” in been changed. Section 4 of this manual. 7. To reactivate this feature, repeat the above steps. •...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 WINDOWS Power Windows You can control either the front or rear windows using Power Vent Windows — If Equipped switches located on the driver’s door trim panel. The Switches on the driver’s door trim panel let the driver switches will operate only when the ignition switch is in operate the two vent windows from the driver’s seat.
Page 36
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Power Window switches will also remain active for up to 10 minutes after the ignition switch has been turned to LOCK, depending upon the accessory delay setting. Opening a front door will cancel this feature. Power Window Lockout Switch —...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 The switches will operate only when the ignition switch is in the ON or ACC position and during power acces- sory delay. Front Passenger Power Window Switches 1 - Window Open/Close 3 - Doors Unlock 2 - Doors Lock Sliding Door Power Window Switch Sliding Side Door Power Window Switch —...
Page 38
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto-Down Feature — If Equipped To stop the window from going all the way up during the The front window switches may be equipped with an Auto Up operation, push down on the switch briefly. Auto-Down feature.
Page 39
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 Wind Buffeting WARNING! Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the There is no anti-pinch protection when the window ears. Your vehicle may exhibit wind buffeting with the is almost closed.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SLIDING SIDE DOOR door after the hold-open latch is activated, you must The sliding door may be opened from the inside or the rock the inside handle forward or pull outward on the outside.
Page 41
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 NOTE: Pulling the outside power sliding door handle a second time while the sliding door is power opening or power closing will allow the sliding door to be opened or closed manually. Press the button on the RKE transmitter twice within five seconds to open a power sliding door.
Page 42
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the power sliding door encounters multiple obstruc- To avoid unintentional operation of the power sliding doors from the rear seats, press the power sliding door tions within the same cycle, the system will automati- master lock button, located in the overhead console, to cally stop and must be opened or closed manually.
Page 43
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 2. Cycle the ignition switch ON/LOCK five times ending opened or closed by pressing the switch located on the in the ON position (do not start the engine). trim panel just in front of the sliding door or activating the inside power sliding door handle.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Sliding Side Door Child Protection Lock To provide a safer environment for small children riding in the rear seats, the sliding doors are equipped with a Child Protection Door Lock system. NOTE: When the Child Protection Door Lock system is engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position.
Page 45
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 NOTE: WARNING! • After engaging the Child Protection Door Lock, al- ways test the door from the inside to make certain it is Avoid trapping anyone in the vehicle in a collision. in the desired position.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: To open the liftgate, depress the liftgate release handle • After setting the Child Protection Door Lock system, located on the underside of the license plate bar and pull always test the door from the inside to make certain it the liftgate open with one fluid motion.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 If the liftgate is locked and is not equipped with the power liftgate feature, pressing the button on the RKE transmitter will result in the liftgate becoming unlocked for 30 seconds allowing you to manually access the liftgate area.
Page 48
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The power liftgate may be closed by pressing the button, When the RKE transmitter button is pressed and the located in the upper left trim in the liftgate opening. Flash Lights feature is enabled, the tail lights will flash to Pushing once will only close the liftgate.
Page 49
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 • There are also pinch sensors attached to the side of the (62°C). Be sure to remove any buildup of snow or ice liftgate opening. Light pressure anywhere along these from the liftgate before pressing any of the power strips will cause the liftgate to return to the open liftgate buttons.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Supplemental Side Airbag Inflatable Curtains (SABIC) Gas props support the liftgate in the open position. However, because the gas pressure drops with tempera- that span the front, second, and third row seating for ture, it may be necessary to assist the props when the driver and passengers seated next to a window —...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 NOTE: The Advanced Front Airbags have a multistage and cause a collision that includes you. This can happen inflator design. This allows the airbag to have different far away from home or on your own street. rates of inflation based on severity and type of collision.
Page 52
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Wearing your belt in the wrong place could make • It is extremely dangerous to ride in a cargo area, your injuries in a collision much worse. You might inside or outside of a vehicle.
Page 53
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 2. The seat belt latch plate is near the seatback of the WARNING! front seats and next to your arm in the rear seats. Grasp • A belt that is worn under your arm is very danger- the latch plate and pull out the belt.
Page 54
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch WARNING! plate into the buckle until you hear a “click”. • A belt that is buckled into the wrong buckle will not protect you properly.
Page 55
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 4. Position the lap belt across your thighs, below your WARNING! abdomen. To remove slack in the lap belt portion, pull up • A lap belt worn too high can increase the risk of on the shoulder belt.
Page 56
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Position the shoulder belt on your chest so that it is WARNING! comfortable and not resting on your neck. When the belt is long enough to fit, insert the large latch plate into the A frayed or torn belt could rip apart in a collision and buckle until you hear a “click.”...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 Automatic Locking Retractors (ALR) Mode — If Equipped In this mode, the shoulder belt is automatically pre- locked. The belt will still retract to remove any slack in the shoulder belt. The Automatic Locking Mode is avail- able on all passenger-seating positions with a combina- tion lap/shoulder belt.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Allow the belt to retract. As the belt retracts, you will NOTE: These devices are not a substitute for proper seat hear a clicking sound. This indicates the safety belt is belt placement by the occupant.
Page 59
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 How the Active Head Restraints (AHR) work The Occupant Restraint Controller (ORC) determines whether the severity or type of rear impact require the Active Head Restraints (AHR) to deploy. In case of AHR deployment both driver and passenger seat AHR’s will be deployed.
Page 60
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Grasp the deployed AHR from the rear seat. CAUTION! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of an accident.
Page 61
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Down And Rearward Reset Movement Down Movement To Engage Locking Mechanism...
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For safety reasons, have the Active Head Restraints 4. The AHR front soft foam and trim half should lock into the back decorative plastic half. checked by a qualified specialist at an authorized dealer.
4. Turn the ignition switch to the LOCK position. A 60 seconds of the ignition switch being turned to the ON single chime will sound to signify that you have success- or START position. Chrysler Group LLC does not recom- fully completed the programming. mend deactivating BeltAlert .
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Keep the belt low so that it does not come across the Supplemental Restraint System (SRS) - Airbags abdomen. That way the strong bones of the hips will take This vehicle has airbags for both the driver and front the force if there is a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 • Steering Wheel and Column driver, front, and rear passengers sitting next to a win- dow. If the vehicle is equipped with SABIC airbags, they • Instrument Panel are located above the side windows and their covers are •...
Page 66
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the second stage determines whether the output force is Supplemental Seat Side Airbags — If Equipped low, medium, or high. If a low output is sufficient to meet Supplemental seat side airbags provide enhanced protec- the need, the remaining gas in the inflator is expended.
Page 67
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 • Airbag covers may not be obvious in the interior trim; When the bag deploys, it opens the seam between the front and side of the seat’s trim cover. Each bag deploys but they will open during airbag deployment.
Page 68
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Along with seat belts and pretensioners, Advanced Front WARNING! Airbags work with the knee bolsters to provide improved protection for the driver and front passenger. Side airbags Infants in rear-facing child restraints should NEVER also work with seat belts to improve occupant protection.
Page 69
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 You should read the instructions provided with your WARNING! child restraint to make sure that you are using it properly. • Relying on the airbags alone could lead to more All occupants should ALWAYS wear their lap and shoul- severe injuries in a collision.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Deployment Sensors and Controls The Advanced Front Airbags will not deploy in all frontal collisions, including some that may produce substantial Occupant Restraint Controller (ORC) vehicle damage — for example, some pole collisions, The ORC is part of a Federally regulated safety system truck underrides, and angle offset collisions.
Page 71
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 The ORC monitors the readiness of the electronic parts of It also includes diagnostics that will illuminate the instru- the system whenever the ignition switch is in the START ment cluster Airbag Warning Light if a malfunction is or ON position.
Page 72
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the Advanced Front Airbags. Different airbag inflation The ORC determines if a side collision requires the side rates are possible, based on the collision type and sever- airbags to inflate based on the severity and type of ity.
Page 73
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Supplemental Side Airbag Inflatable Curtain Because airbag sensors estimate deceleration over time, (SABIC) Inflator Units — If Equipped vehicle speed and damage are not good indicators of During collisions where the impact is confined to a whether or not an airbag should have deployed.
Page 74
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Flash hazard lights as long as the battery has power or passenger as the airbags deploy and unfold. The until the ignition key is turned off. abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium •...
Page 75
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Do not drive your vehicle after the airbags have de- Maintaining Your Airbag System ployed. If you are involved in another collision, the WARNING! airbags will not be in place to protect you. •...
Page 76
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Warning Light WARNING! (Continued) You will want to have the airbags ready to • Do not attempt to modify any part of your ad- inflate for your protection in a collision. While vanced airbag system.
In the event of an accident, your vehicle is designed to used by Chrysler Group LLC and others to learn more record up to five seconds of specific vehicle data param- about the possible causes of crashes and associated...
• Engine RPM hicle, or crash, will be treated confidentially. Confidential • Brake switch status data will not be disclosed by Chrysler Group LLC to any • Pedal position third party except when: • And...
Page 79
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 The booster seat is designed to raise the child high To position a child into the Integrated Child Booster Seat enough to use the vehicle lap and shoulder belt. The follow these steps: booster seat latch release handle is located at the front of 1.
Page 80
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The lap portion of the seat belt should be low on WARNING! the hips and as snug as possible. Failure to comply with the following conditions 5. Once the seat belt is long enough to fit properly, insert could result in serious injury of death: the latch plate into the buckle until you hear a “click.”...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 7. To release the seat belt, push the red button on the To obtain Integrated Child Seat replacement instruc- buckle. tions: Refer to Publication Order Forms in Section 9 and specify publication number 81–016–8050 when ordering. Integrated Child Seat —...
Page 82
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Safety experts recommend that children ride rearward- WARNING! facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types of child In a collision, an unrestrained child, even a tiny baby, restraints can be used rearward-facing: infant carriers can become a projectile inside the vehicle.
Page 83
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 Older Children and Child Restraints WARNING! Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the Rearward-facing child seats must NEVER be used in vehicle.
Page 84
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children Too Large for Booster Seats NOTE: For additional information, refer to Children who are large enough to wear the shoulder belt www.seatcheck.org or call 1–866–SEATCHECK. Cana- comfortably, and whose legs are long enough to bend dian residents, should refer to Transport Canada’s web- over the front of the seat when their back is against the site for additional information.
Page 85
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 • Carefully follow the instructions that come with the WARNING! (Continued) restraint. If you install the restraint improperly, it may • Occupants riding in Swivel ’n Go seating must be not work when you need it. wearing their seat belt and the seat must be locked •...
Page 86
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the belt still can’t be tightened, or if pulling and connector, and a means for adjusting the tension in the pushing on the restraint loosens the belt, disconnect strap. Forward-facing toddler restraints and some the latch plate from the buckle, turn the buckle rearward-facing infant restraints will also be equipped around, and insert the latch plate into the buckle...
Page 87
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 NOTE: WARNING! • When using the LATCH attaching system to install a child restraint, please ensure that all seat belts not Improper installation of a child restraint to the being used for occupant restraints are stowed and out LATCH anchorages can lead to failure of an infant or of reach of children.
Page 88
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing the Lower Attachments: 4. Tighten the lower attachment strap while firmly push- ing the child restraint rearward and downward into the 1. The vehicle lower anchorages are round bars located vehicle seat. Remove all slack in the lower attachment at the rear of the seat cushion where it meets the seatback.
Page 89
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 Installing the Top Tether Strap (with either Lower Anchors or Vehicle Seat Belt): 1. Route the top tether strap under the adjustable head restraint between the steel posts. 2. Provide enough slack (reference child restraint in- structions) for the tether strap to reach the tether anchor located near the bottom of the seat back.
Page 90
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To install a child restraint, first, pull enough of the seat WARNING! belt webbing from the retractor to route it through the belt path of the child restraint and slide the latch plate An incorrectly anchored tether strap could lead to into the buckle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts. REAR SEAT DELETE FEATURE (COMMERCIAL VEHICLES ONLY) — IF EQUIPPED Commercial cargo vehicles are not designed for use as a family vehicle and are not intended for carrying children in the front passenger seat.
92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The forward-facing child seat is for children from WARNING! about 20 to 40 lbs (9 to 18 kg), and more than one year old. Rearward-facing infant restraints must never be se- cured in the passenger seat of a vehicle with a •...
Page 93
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 with the seat adjusted to the rearmost position. Never 4. Using the hook attached to the child restraint tether allow children to slide the shoulder belt behind them strap, attach the child restraint tether strap to the metal or under their arm.
94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE While cruising, brief full-throttle acceleration within the WARNING! limits of local traffic laws, contributes to a good break-in. Wide-open throttle acceleration in low gear can be detri- The vehicle tether anchor is designed to be used with mental and should be avoided.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 SAFETY TIPS Exhaust Gas Transporting Passengers WARNING! NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. WARNING! Breathing it can make you unconscious and can eventually poison you.
96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you are required to drive with the liftgate open, make Safety Checks You Should Make Inside the sure that all windows are closed and the climate control Vehicle BLOWER switch is set at high speed. DO NOT use the Seat Belts recirculation mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 Defroster Lights Check operation by selecting the defrost mode and place Have someone observe the operation of exterior lights the blower control on high speed. You should be able to feel while you work the controls. Check turn signal and high the air directed against the windshield.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS ▫ Tilt Mirrors In Reverse (Available With Mirrors ......104 Memory Seat Only) —...
Page 100
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Third Row Power Seat — If Equipped ..138 Seats ......117 ▫...
Page 101
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 ▫ Daytime Running Lights — If Equipped ..152 ▫ To Set At A Desired Speed ....160 ▫...
Page 102
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Parkview Rear Back Up Camera — Power Sunroof — If Equipped ... . 182 If Equipped ......171 ▫...
Page 103
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 ▫ Second Row Seat Storage Bins — ▫ Premium Console — If Equipped ..199 If Equipped ......194 Rear Window Features .
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror — If Equipped A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Outside Mirrors To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. WARNING! Vehicles and other objects seen in an outside convex mirror will look smaller and farther away than they really are.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE inside mirror. The mirror will automatically adjust for headlight glare when the inside mirror adjusts. Outside Mirror Folding Feature All outside mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have three detent positions: full forward, full rearward and normal.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 Driver’s side power mirror preselected positions can be will move slightly downward from the present position controlled by the optional Driver Memory Seat Feature. when the vehicle is shifted into REVERSE. The driver’s Refer to “Driver Memory Seat”...
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Illuminated Vanity Mirrors — If Equipped uconnect™ phone — IF EQUIPPED An illuminated vanity mirror is located on the sun visor. Refer to “uconnect™ phone” in the uconnect™ User To use the mirror, rotate the sun visor down and swing Manual located on the DVD for further details.
Page 109
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 The BSM detection zone covers approximately one lane on both sides of the vehicle (11 ft or 3.35 m). The zone starts at the outside rear view mirror and extends ap- proximately 20 ft (6 m) to the rear of the vehicle. The BSM system monitors the detection zones on both sides of the vehicle when the vehicle speed has reached approxi- mately 6 mph (10 km/h) or higher and will alert the...
Page 110
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The BSM system detection zone DOES NOT change if your vehicle is towing a trailer. Therefore, visually verify the adjacent lane is clear for both your vehicle and trailer before making a lane change. If the trailer or other object (i.e., bicycle, sports equipment) extends beyond the side of your vehicle, this may result in the BSM warning light remaining illuminated the entire...
Page 111
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 The BSM system monitors the detection zone from three different entry points (Side, Rear, Front) while driving to see if an alert is necessary. The BSM system will issue an alert during these types of zone entries. Entering From The Side Vehicles that move into your adjacent lanes from either side of the vehicle.
Page 112
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Entering From The Rear Overtaking Traffic Vehicles that come up from behind your vehicle on either If you pass another vehicle slowly (with a relative speed side and enter the rear detection zone with a relative less than 10 mph (16 km/h) and the vehicle remains in speed of less than 30 mph (48 km/h).
Page 113
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 The BSM system is designed not to issue an alert on stationary objects such as guardrails, posts, walls, foliage, berms, etc. However, occasionally the system may alert on such objects. This is normal operation and your vehicle does not require service.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The BSM system will not alert you of objects that are WARNING! traveling in the opposite direction of the vehicle in adjacent lanes. The Blind Spot Monitoring system is only an aid to help detect objects in the blind spot zones.
Page 115
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 NOTE: In a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver. When RCP is on and the vehicle is in REVERSE, the driver is alerted using both the visual and audible alarms, including radio muting.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Modes Of Operation Blind Spot Alert Lights/Chime Three selectable modes of operation are available in the When operating in Blind Spot Alert Lights/Chime, the Electronic Vehicle Information Center (EVIC). Refer to BSM system will provide a visual alert in the appropriate “Personal Settings (Customer-Programmable Features) side view mirror based on a detected object.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 object is present. Whenever an audible alert is re- SEATS quested, the radio is also muted. Turn/hazard signal Seats are a primary part of the Occupant Restraint System status is ignored; the RCP state always requests the of the vehicle.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Front And Second Row Seat Adjuster WARNING! The adjusting bar is located under the front of the seat. Pull the bar upward and move the seat to the desired Adjusting a seat while the vehicle is moving is position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 Manual Lumbar Adjust Lever — If Equipped The lumbar adjustment lever is located on the outboard side of the seat. To increase the support, rotate the lever downward. To decrease the support, rotate the handle upward.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Heated Seats — If Equipped WARNING! This feature heats the front driver and passenger seats. The controls for front heated seats are located on the Adjusting a seat while the vehicle is moving is center instrument panel area.
Page 122
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Second row heated seat switches are located in the WARNING! sliding side door handle trim panels and function the same as front switches. Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Adjusting Active Head Restraints To raise the head restraint, pull upward on the head Active Head Restraints can reduce the risk of injury in restraint (on some models, you may need to press the the event of a rear impact.
Page 124
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE For comfort the Active Head Restraints can be tilted forward and backward. To tilt the head restraint closer to the back of your head, pull outward on the bottom of the head restraint. Push rearward on the bottom of the head restraint to move the head restraint away from your head.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 NOTE: WARNING! (Continued) • The head restraints should only be removed by quali- • Do not place items over the top of the Active Head fied technicians, for service purposes only. If either of Restraint, such as coats or seat covers.
Page 126
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Slide the storage bin locking mechanism to the 4. Pull up on the seatback recliner lever located on the LOCK position and then pull up on the storage bin latch outboard side of the seat and fold the seatback down. To to open the cover.
Page 127
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 5. Pull rearward on the release strap located at the rear of CAUTION! the seat and tumble the seat forward into the storage bin. The storage bin cover must be locked and flat to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Pull up on the handle to lift the seat out of the storage bin and push the seat rearward to latch the seat anchors. Second Row Seatback Release Lever 4. Adjust the head restraint to the desired position, close the storage bin cover and slide the storage bin locking Second Row Seat Release Handle mechanism to the Unlocked position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 To tilt the seat, pull forward on the release strap located WARNING! on the front of the seat between the seatback and seat cushion and tilt the seat fully forward. In the event of a collision you could be injured if the seat is not fully latched.
Page 130
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Seats are removable WARNING! When the seatback release handle is lifted, the seat- back will rotate forward. To avoid injury, if you are not seated in the seat, stay clear from the area in the path of the rotating seatback.
Page 131
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 WARNING! Failure to comply with the following conditions could result in serious injury or even death: • NEVER place any child seat or infant carrier in the Swivel ’n Go™ seat while it is in the rearward facing position.
Page 132
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Removing Swivel ’n Go™ Premium Seating — If 3. From behind the seat, lift up on the rear of the seat Equipped cushion while pulling the seat in a rearward direction. 1. Remove any obstructions from the floor behind the 4.
Page 133
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 WARNING! In a collision, you or others in your vehicle could be injured if seats are not properly latched to their floor attachments. Always be sure the seats are fully latched. Swivel ’n Go™ Premium Seating Table — If Equipped The Swivel ’n Go™...
Page 134
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The table and leg are stored beneath the floor when not in 3. Swivel the second row seats so they are facing the rear. use. To install the table follow these steps: 4. Insert pole into base by aligning the lock button into 1.
Page 135
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 NOTE: You will hear an audible “click” when the lock WARNING! button engages the base. Failure to comply with the following conditions 6. Place the table top over the installed pole aligning could result in serious injury or even death: with the mating feature of the underside of the table top.
Page 136
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To separate the table top from the pole, follow these 3. While pulling on the latch, pull upward to remove the steps: table top from the pole. 1. Locate the release latch on the underside of the table NOTE: The table top should be removed from the leg top.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 Plastic Grocery Bag Retainer Hooks Retainer hooks which will hold plastic grocery bag handles are built into the seatbacks of all rear seats and some front seats. The floor supports the partial weight of the bagged goods.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! If not properly latched, the bench seats could become loose. Personal injuries could result. After reinstall- ing these seats, be sure the red indicator button on the release handles return into the handles. Third Row Power Seat —...
Page 139
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Rear Panel Power Switch Bank One Touch Folding Seat Third Row The rear switch bank allows multiple power folding and 1 — Open to Normal 4 — Fold Flat 2 — Stow 5 — Right/Left Seats unfolding positions for the third row seats.
Page 140
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: 2. Pull release strap marked “1” located on the rear of the • Disconnect the center shoulder belt from the small seat to lower the seatback. buckle and lower the head restraints before attempting 3.
Page 141
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 To Unfold Third Row Seats Tailgate Mode 1. Pull up on the assist strap to lift the seat out of the 1. Pull release strap “2”, then pull release strap “3” to storage bin and push the seat forward until the anchors rotate the entire seat rearward.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! To avoid serious injury or death, NEVER operate the vehicle with occupants in the third row seat while in the tailgate mode. DRIVER MEMORY SEAT — IF EQUIPPED The Memory Buttons 1 and 2 on the driver’s door panel can be programmed to recall the driver’s seat, driver’s outside mirror, adjustable brake and accelerator pedals, and radio station preset settings.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Setting Memory Positions and Linking RKE 5. Turn on the radio and set the radio station presets (up Transmitter to Memory to 10 AM and 10 FM stations can be set). NOTE: Each time the SET (S) button and a numbered 6.
Page 144
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 11. Select Remote Linked to Memory in the Electronic To recall the memory setting for driver two, press Vehicle Information Center (EVIC) and enter “Yes”. Refer MEMORY button 2 on the driver’s door or the UNLOCK to the “Customer-Programmable Features”...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 3. Press and release the memory SET (S) button located Easy Entry/Exit Seat on the driver’s door. A chime will sound signaling that (Available with Memory Seat ONLY) you are in the memory set mode. This feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the 4.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE between 0.9 – 2.7 in (22.7 – 67.7 mm) forward of the TO OPEN AND CLOSE THE HOOD rear stop. The seat will return to its previously set To open the hood, two latches must be released. position when you insert the key into the ignition 1.
Page 147
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 2. Move to the front of the vehicle and look inside the CAUTION! center of the hood opening. Locate, then push the safety catch lever to the right while raising the hood at the same To prevent possible damage, do not slam the hood to time.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Interior Lighting All of the lights, except the Hazard Warning lights, Interior lights are turned on when a door or liftgate is headlight high beams and flash-to-pass, are controlled by opened, the Remote Keyless Entry (RKE) transmitter is switches to the left of the steering column on the instru- activated, or when the dimmer control is moved to the ment panel.
Page 149
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 Dome Light Positions Parade Mode (Daytime Brightness Feature) Rotate the dimmer control completely Rotate the dimmer control to the first upward to the second detent (extreme detent. This feature brightens the top position) to turn on the interior odometer, radio and overhead dis- lights.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Halo Lights — If Equipped To change the brightness of the instrument panel lights, Halo lights are strategically placed soft lighting that help rotate the dimmer control up or down. to illuminate specific areas to aid the occupants in Automatic Headlights —...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 on when windshield wipers are on may be found on vehicles equipped with an automatic headlight system. Refer to the Electronic Vehicle Information Center (EVIC) in Section 4 under “Personal Settings (customer-pro- grammable features)” for more information. Headlight Delay —...
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The headlight delay time is programmable on vehicles except PARK. This provides a constant lights on condi- equipped with an EVIC. Refer to “Delay Turning Head- tion until the ignition is turned OFF. The lights illuminate lights Off,”...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 • Front and Rear Wipers — Washer Functions when the ignition switch is in the LOCK position. After eight minutes of the ignition switch being in the LOCK Turn Signals position and the headlight switch in any position other Move the multifunction lever up or down and the arrows than OFF or AUTO, the lights will turn off automatically on each side of the instrument cluster flash to show...
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If either light remains on and does not flash, or High/Low Beam Switch there is a very fast flash rate, check for a defective outside When the headlights are turned on, pushing the multi- light bulb.
Page 155
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 off position. If the windshield wiper switch is turned off 1. Mist, Front Wiper and Washer and the blades cannot return to the off position, damage Press the end of the multifunction lever inward to the to the wiper motor may occur.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Intermittent, Low and High Speed Wipers the rotary ring fully forward and the washers will spray Use the intermittent wipers when weather conditions until the ring is released, and then resume the intermit- make a single wiping cycle, with a variable pause be- tent interval.
Page 157
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 To tilt the column, push the lever downward to the WARNING! unlocked position. Move the steering column up or down, as desired. Pull the lever upward to the locked Tilting the steering column while the vehicle is position to lock the steering column firmly in place.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ADJUSTABLE PEDALS — IF EQUIPPED Press the button forward to move the pedals forward This feature allows both the brake and accelerator pedals (toward the front of the vehicle). to move toward, or away, from the driver to provide Press the button rearward to move the pedals rearward improved position with the steering wheel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 CAUTION! Do not place any article under the adjustable pedals or impede its ability to move, as it may cause damage to the pedal controls. Pedal travel may become lim- ited if movement is stopped by an obstruction in the adjustable pedal’s path.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Activate To Set At A Desired Speed Push the ON/OFF button (located in the end of the lever) When the vehicle has reached the desired speed, press once, and the cruise indicator light (located in the mes- the SET lever downward and then release.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 Varying The Speed Setting in 5 mph (10 km/h) increments until the lever is released. When the Electronic Speed Control is set, you can in- Release the Electronic Speed Control lever when the crease speed by pushing up and holding the Electronic desired speed is reached, and a new set speed will be Speed Control lever in RESUME ACCEL.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Your vehicle may experience a downshift (automatic PARKSENSE REAR PARK ASSIST — IF transmissions only) while climbing uphill or descending EQUIPPED downhill. This downshift is necessary to maintain vehicle The ParkSense Rear Park Assist system provides visual set speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 ParkSense Sensors The ParkSense Warning Display is located in the Instru- The ParkSense sensors, located in the rear fascia/ ment cluster’s EVIC display. It provides both visual and bumper, monitor the area behind the vehicle that is audible warnings to indicate the distance between the within the sensors’...
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense Display When the vehicle is in REVERSE, the warning display will turn ON indicating the system status. Park Assist Disabled The system will indicate a detected obstacle by showing three solid arcs and will produce a ⁄...
Page 165
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 Slow Tone Fast Tone...
Page 166
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The vehicle is close to the obstacle when the EVIC display shows one flashing arc and sounds a continuous tone. The following chart shows the warning display operation when the system is detecting an obstacle: Continuous Tone...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 WARNING DISPLAY DISTANCES DISPLAY MESSAGE OBSTACLE DISTANCE FROM: ARC’s AUDIBLE SIGNAL REAR CORNERS REAR CENTER Park Assist ON None None Warning Object Detected 78.7 in (200 cm) 3 Solid Yes, 1/2 second Warning Object Detected 39.3 in (100 cm) 3 Flashing Slow Tone...
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the shift lever is moved to REVERSE and the If “SERVICE PARK ASSIST SYSTEM” appears in the system is disabled, the EVIC will display the “PARK Electronic Vehicle Information Center (EVIC) after mak- ASSIST DISABLED”...
Page 169
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 • When you turn ParkSense off, the instrument cluster • Clean the ParkSense sensors regularly, taking care will display “PARK ASSIST DISABLED.” Further- not to scratch or damage them. The sensors must not more, once you turn ParkSense off, it remains off be covered with ice, snow, slush, mud, dirt, or debris.
Page 170
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! • ParkSense is only a parking aid and it is unable • Drivers must be careful when backing up even to recognize every obstacle, including small ob- when using the ParkSense Rear Park Assist sys- stacles.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 PARKVIEW REAR BACK UP CAMERA — IF WARNING! (Continued) EQUIPPED • Before using the ParkSense Rear Park Assist Your vehicle may be equipped with the ParkView Rear system, it is strongly recommended that the ball Back Up Camera that allows you to see an on-screen mount and hitch ball assembly is disconnected image of the rear of your vehicle whenever the shift lever...
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Press the “camera setup” soft key. CAUTION! 4. Enable or disable the rear camera feature by selecting • To avoid vehicle damage, ParkView should only enable rear camera in reverse soft key. be used as a parking aid.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 4. When the vehicle is shifted into REVERSE, an image of NOTE: Premium sunroof console models include all of the rear of the vehicle will appear with a caution note to above except sunglass storage. check entire surroundings displayed across the top of the screen.
Page 174
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Courtesy/Interior Lighting Sunglass Storage (non-sunroof only) At the forward end of the console are two courtesy lights At the rear of the front overhead console, a compartment (standard dome light has two buttons). The lights turn on is provided for the storage of two pairs of sunglasses.
Page 175
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 An additional LED at the front of the rear console shines Rear Courtesy/Reading Lights — If Equipped down on the front foot-well area while in courtesy mode, The overhead console has two sets of courtesy lights. The for added convenience.
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Console Halo Lighting The rear overhead console has recessed halo lighting around the perimeter of the console base. This feature provides additional lighting options while traveling and is controlled by the headlight switch. Refer to ”Halo Lights —...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 Programming HomeLink WARNING! Before You Begin • Your motorized door or gate will open and close If you have not trained any of the HomeLink buttons, while you are training the universal transceiver. erase all channels before you begin training.
Page 178
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After training a HomeLink channel, if the garage Place the handheld transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink button you wish to program while door does not operate with HomeLink and the ga- keeping the indicator light in view.
Page 179
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 This can usually be found where the hanging antenna 6. Firmly press and release the LEARN or TRAINING wire is attached to the garage door opener motor. It is button. The name and color of the button may vary by NOT the button normally used to open and close the manufacturer.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using HomeLink Gate Operator/Canadian Programming To operate, press and release the programmed Canadian radio frequency laws require transmitter sig- HomeLink button. Activation will now occur for the nals to time-out (or quit) after several seconds of trans- trained device (i.e., garage door opener, gate operator, mission –...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 successfully accepted the frequency signal. The indica- Troubleshooting Tips tor light will flash slowly and then rapidly when fully If you are having trouble programming HomeLink , here trained. are some of the most common solutions: •...
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. This device must accept any interference that may be Power Sunroof Operation received including interference that may cause undesired Opening the Sunroof Manually operation. Press the switch rearward and hold, and the sunroof will NOTE: open automatically from any position.
Page 183
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 Closing the Sunroof Manually Express Open To close the sunroof from an open or vent position, press Press the switch rearward and release, and the sunroof and hold the switch forward. The sunroof will close fully will open automatically from any position.
Page 184
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Auto Express will stop and reverse travel up to three WARNING! times in succession. After the third time, Auto Express will enter a manual operation mode. This allows the Do not allow small children to operate the sunroof. operator to manually control the power switch, in order Never allow your fingers, other body parts, or any to close or open the sunroof in case of a malfunction.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. ELECTRICAL POWER OUTLETS — IF EQUIPPED Two 12 Volt power outlets are located on the lower instrument panel, next to the open storage bin. The upper power outlet is controlled by the ignition switch and the lower power outlet is connected directly to the battery.
Page 186
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The outlet in the rear quarter panel near the liftgate and WARNING! (Continued) the upper outlet in the instrument panel are both con- • Close the lid when not in use and while driving trolled by the ignition switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 POWER INVERTER — IF EQUIPPED CAUTION! (Continued) A 110 Volt, 150 Watt inverter outlet (if equipped) converts • Accessories that draw higher power (i.e., coolers, DC current to AC current, and is located on the left rear vacuum cleaners, lights, etc.), will degrade the trim panel immediately behind the second row left battery even more quickly.
Page 188
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE manually press the power inverter button OFF and ON. To turn on the power outlet, press the switch once. Press To avoid overloading the circuit, check the power ratings the switch a second time to turn the power outlet off. on electrical devices prior to using the inverter.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 CUPHOLDERS There are nine cupholders in the interior. Two cupholders in the center front instrument panel, four in the floor consoles and three more are located in the third row quarter trim panel. All liners are removable for cleaning.
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Bottle Holders There are four bottle holders located in the interior. One bottle holder is molded into each front interior door trim panels, and one bottle holder is molded into each side sliding interior door trim panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 of the two cupholders in the center front instrument To close the compartment door, firmly push downward panel. To install the ash receiver, align the receiver so the on the door’s surface to release the detent and latch the thumb grip on the lid is facing rearward.
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lower Glove Compartment To open the lower compartment pull out on the release handle. NOTE: The lower compartment is equipped with a lock that is part of the compartment handle (2). Door Trim Panel Storage Front Door Storage Both interior front door panels have multiple pockets for storage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 Sliding Side Door Bottle Holder Driver Seatback Storage — If Equipped Both sliding doors have a bottle holder molded right into The driver’s seatback has a primary storage pocket on all the trim. models and an optional secondary mesh pocket.
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Umbrella Holder Second Row Seat Storage Bins — If Equipped An umbrella holder has been conveniently molded into The seat storage bins are located on the floor in front of the left front door entry scuff molding. the second row seats.
Page 195
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 CAUTION! NOTE: The storage bin cover must be locked and flat to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover. WARNING! In an accident, serious injury could result if the seat storage bin covers are not properly latched.
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage Bin Safety Warning WARNING! (Continued) Carefully follow these warnings to help prevent personal • Do not operate the storage bin covers while the injury or damage to your vehicle: vehicle is in motion. •...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 NOTE: In the event of an individual being locked inside the storage bin, the storage bin cover can be opened from inside of the bin by pushing on the glow-in-the-dark lever attached to the storage bin cover latching mechanism.
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Area Storage NOTE: With all rear seats stowed or removed, 4 x 8 foot The liftgate sill plate has a raised line with the statement sheets of building material will fit on the vehicle floor “Load To This Line”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 • The basic console is removable from the vehicle for 4. Reinstall the clip first and then while pushing down- additional floor space by removing the cap and clip at ward on the console with slight pressure, reinstall the the console base.
Page 200
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Top tray storage • Upper storage bin can hold nine regular or 18 thin CDs or other items • Large console center storage will store headphones for the available rear DVD entertainment system or other items •...
Page 201
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 Position 1 shows the console closed with four cupholders and a convenient storage tray. Console Position 2 Console Position 1 Position 2 shows the raised storage tray revealing a large storage area below.
Page 202
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dual Storage Bins Position 4 shows the complete console in its rearmost Position 3 shows the top portion of the console in a position. Again, lifting second latch handle at the front of rearward position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 To Remove The Premium Floor Console 5. Pull up on the console to be sure it is firmly latched. 1. Pull up on the bottom release handle in the front of the WARNING! console.
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: CAUTION! (Continued) • You can turn off the heated mirror feature at anytime • Do not use scrapers, sharp instruments, or abra- by pressing the rear window defroster switch a second sive window cleaners on the interior surface of the time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 ROOF LUGGAGE RACK — IF EQUIPPED Attempt to move the crossbar again to ensure that it has The crossbars and side rails are designed to carry the properly locked into position. weight on vehicles equipped with a luggage rack. The NOTE: To help control wind noise when installing the load must not exceed 150 lbs (68 kg), and should be crossbars make sure the arrows marked on the underside...
Page 206
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! CAUTION! (Continued) • Travel at reduced speeds and turn corners care- • Crossbars should remain equally spaced or paral- fully when carrying large or heavy loads on the lel at any luggage rack position for proper func- roof rack.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 WARNING! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in per- sonal injury or property damage. Follow the Roof Rack Cautions when carrying cargo on your roof rack.
Page 208
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Gently pull up on the tab to raise the sun screen. Continue pulling the sun screen until the tab is near the top of the window. Sun Screen Extended To lower the sun screen, gently lift the tab upward to disengage the hooks, and feed the screen back into the base sill.
Page 209
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....213 Electronic Vehicle Information Center (EVIC) — If Equipped ......233 Instrument Cluster –...
Page 210
210 UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM/CD/DVD Radio (RER & RBZ) – Sales Code RES/RSC — AM/FM Stereo Radio If Equipped ......245 With CD Player (MP3 AUX Jack) And Sirius Radio.
Page 211
UNDERSTANDING YOUR INSTRUMENT PANEL 211 ▫ Play Mode ......272 uconnect™ studios (Sirius Backseat TV™) — If Equipped .
Page 212
212 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Rear Manual Climate Control — ▫ Vacation/Storage ....301 If Equipped ......290 ▫...
216 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, 1. Fuel Gauge or when towing a trailer. It should not be allowed to The pointer shows the level of fuel in the fuel tank when exceed the upper limits of the normal operating range.
Page 217
UNDERSTANDING YOUR INSTRUMENT PANEL 217 continuous chime will sound to alert you to turn the WARNING! signals off. If either indicator flashes at a rapid rate, check for a defective outside light bulb. A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling 6.
Page 218
218 UNDERSTANDING YOUR INSTRUMENT PANEL If the ABS light is on, the brake system should be serviced In this case, the light will remain on until the condition has as soon as possible to restore the benefits of Anti-Lock been corrected. If the problem is related to the brake brakes.
Page 219
UNDERSTANDING YOUR INSTRUMENT PANEL 219 The light also will turn on when the parking brake is WARNING! applied with the ignition switch in the ON position. Driving a vehicle with the red brake light on is NOTE: This light shows only that the parking brake is dangerous.
Page 220
220 UNDERSTANDING YOUR INSTRUMENT PANEL U.S. Federal regulations require that upon transfer of 12. Message Display Area vehicle ownership, the seller certify to the purchaser the When the appropriate conditions exist, the following correct mileage that the vehicle has been driven. If your odometer messages will display: odometer needs to be repaired or serviced, the repair technician should leave the odometer reading the same...
Page 221
UNDERSTANDING YOUR INSTRUMENT PANEL 221 NOTE: The ECO display will toggle between ECO and ECO-on • If your vehicle is equipped with a hood switch, in the depending on driving habits and vehicle usage. case of hood ajar, a warning message will be displayed LoW tirE in either the PRNDL/Odometer display as “hood”...
Page 222
222 UNDERSTANDING YOUR INSTRUMENT PANEL gASCAP 12 seconds after a single chime has sounded to indicate If the vehicle diagnostic system determines that the fuel the next scheduled oil change interval. The engine oil filler cap is loose, improperly installed, or damaged, a change indicator system is duty cycle-based, which “gASCAP”...
Page 223
UNDERSTANDING YOUR INSTRUMENT PANEL 223 NOTE: If the indicator message illuminates when you several miles (kilometers) at speeds greater than 30 mph start the vehicle, the oil change indicator system did not (48 km/h), see your authorized dealer as soon as possible reset.
Page 224
224 UNDERSTANDING YOUR INSTRUMENT PANEL the ON position before engine start. If the bulb does not WARNING! come on when turning the key from OFF to ON, have the condition checked promptly. A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal Certain conditions such as a loose or missing gas cap, operating conditions.
Page 225
UNDERSTANDING YOUR INSTRUMENT PANEL 225 If the light turns on while driving, safely pull over and If the light remains lit with the engine running, your stop the vehicle. If the A/C system is on, turn it off. Also, vehicle will usually be drivable; however, see an autho- shift the transmission into NEUTRAL and idle the ve- rized dealer for service as soon as possible.
Page 226
226 UNDERSTANDING YOUR INSTRUMENT PANEL 19. Front Fog Light Indicator — If Equipped 22. Airbag Warning Light This indicator will illuminate when the front fog This light turns on and remains on for four lights are on. seconds as a bulb check when the ignition switch is first turned ON.
Page 227
UNDERSTANDING YOUR INSTRUMENT PANEL 227 If jump starting is required, refer to “Jump Starting As an added safety feature, your vehicle has been Procedures” in section 6 of this manual. equipped with a Tire Pressure Monitoring System (TPMS) that illuminates a low tire pressure telltale when 24.
Page 228
228 UNDERSTANDING YOUR INSTRUMENT PANEL Your vehicle has also been equipped with a TPMS CAUTION! malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is The TPMS has been optimized for the original combined with the low tire pressure telltale. When the equipment tires and wheels.
On vehicles equipped with Compass Mini-Trip Com- • If the vehicle is equipped with a Chrysler uconnect™ puter (CMTC), the display provides the outside tempera- gps (Navigation Radio), the NAV system will provide...
230 UNDERSTANDING YOUR INSTRUMENT PANEL the compass direction, and the variance and calibra- When the appropriate conditions exist, the following tion menus will be unavailable. The compass will messages will display: perform accurately, based on GPS signals instead of the Earth’s magnetic field. NE .
UNDERSTANDING YOUR INSTRUMENT PANEL 231 CMTC Trip Odometer (ODO) / ECO (Fuel Saver The ECO display will toggle between ECO and ECO-ON Indicator) — If Equipped depending on driving habits and vehicle usage. This display shows the distance traveled since the last Compass/Temperature Display reset.
Page 232
232 UNDERSTANDING YOUR INSTRUMENT PANEL • Magnetic and battery powered devices, (such as cell To Set the Variance phones, iPod’s, radar detectors, PDA’s and laptops) Start the engine and leave the transmission gear selector should be kept away from the top of the instrument lever in the PARK position.
UNDERSTANDING YOUR INSTRUMENT PANEL 233 2. Press and hold the CMTC reset button (for approxi- mately 10 seconds) until the current variance zone num- ber is displayed. 3. Release the CMTC reset button, then press and hold again for approximately 10 seconds, until the direction is displayed, with the CAL indicator on continuously in the display.
Page 234
234 UNDERSTANDING YOUR INSTRUMENT PANEL • Vehicle information warning message displays Press and release the MENU button, and the mode displayed will change between Compass/ • Tire Pressure Monitor System Temperature, Trip, System Status, and Personal • Personal Settings (Customer-Programmable Features) Settings.
UNDERSTANDING YOUR INSTRUMENT PANEL 235 • RKE Battery Low Press this button to RESET Trip Functions and change Personal Settings. • LOW WASHER FLUID • Oil Change Required Electronic Vehicle Information Center (EVIC) • Left Front Turn Signal Light Out Displays •...
Page 236
236 UNDERSTANDING YOUR INSTRUMENT PANEL • Blind Spot System Not Available — This message is Oil Change Required displayed to indicate the Blind Spot Monitor (BSM) Your vehicle is equipped with an engine oil change system is temporarily unavailable due to sensor block- indicator system.
UNDERSTANDING YOUR INSTRUMENT PANEL 237 2. Fully depress the accelerator pedal, slowly, three times “RESET” or show dashes for two seconds. Then, the within 10 seconds. history information will be erased, and the averaging will continue from the last fuel average reading before the 3.
238 UNDERSTANDING YOUR INSTRUMENT PANEL significant amount of fuel to the vehicle will turn off the Compass Display / ECO (Fuel Saver Mode) — If LOW FUEL text and a new DTE value will display. Equipped The compass readings indicate the direction Elapsed Time the vehicle is facing.
Page 239
UNDERSTANDING YOUR INSTRUMENT PANEL 239 Automatic Compass Calibration 3. Press the STEP button until “Calibrate Compass” is This compass is self-calibrating, which eliminates the displayed in the EVIC. need to manually reset the compass. When the vehicle is 4. Press and release the RESET button to start the cali- new, the compass may appear erratic and the EVIC will bration.
240 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Keep magnetic materials away from the top of 2. Press and hold the compass button for approximately the instrument panel, such as iPod’s, Cell Phones, Lap- two seconds. tops and Radar Detectors. This is where the compass 3.
Page 241
UNDERSTANDING YOUR INSTRUMENT PANEL 241 Use the Step button to display one of the following Auto UNLK On Exit choices. When ON is selected, all doors will unlock when the vehicle is stopped and the transmission is in the PARK or Language NEUTRAL position and the driver’s door is opened.
Page 242
242 UNDERSTANDING YOUR INSTRUMENT PANEL RKE Linked To Memory Headlamp Off Delay When this feature is selected the memory seat, mirror, When this feature is selected, the driver can choose to and radio settings will return to the memory set position have the headlights remain on for 0, 30, 60, or 90 seconds when the RKE transmitter UNLOCK button is pressed.
Page 243
UNDERSTANDING YOUR INSTRUMENT PANEL 243 Tilt MIRR. In Reverse ILLUMIN. Approach When this feature is selected and the vehicle is placed in When this feature is selected, the headlights will activate a reverse gear, the driver’s side mirror will tilt downward and remain on for up to 90 seconds when the doors are to allow the driver to see into the previous blind spot and unlocked with the RKE transmitter.
Page 244
244 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If your vehicle has experienced any damage in Display Units of Measure In the area where the sensor is located, even if the fascia is The EVIC, odometer, and navigation system (if equipped) not damaged, the sensor may have become misaligned. can be changed between English and Metric units of Take your vehicle to an authorized dealer to verify sensor measure.
Page 245
UNDERSTANDING YOUR INSTRUMENT PANEL 245 Turn Headlights On with Remote Key Unlock Rain Sensing Intermittent Wipers — If Equipped When this feature is selected, the headlights will activate, When ON is selected, the system will automatically and remain on for up to 90 seconds, when the doors are activate the windshield wipers if it senses moisture on unlocked with the RKE transmitter.
246 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Voice Recognition 3. To move the hour forward, touch the screen where the System (VR) — If Equipped word “Hour” with the arrow pointing upward is dis- Refer to “Voice Recognition System (VR)” in the played.
UNDERSTANDING YOUR INSTRUMENT PANEL 247 2. Touch the screen where the time is displayed. The Changing the Time Zone clock setting menu will appear on the screen. 1. Turn on the radio. 3. When this feature is on, a check mark will appear in 2.
Page 248
248 UNDERSTANDING YOUR INSTRUMENT PANEL satellite clock is Greenwich Mean Time (GMT). This is the displayed. To move the minute backward, touch the worldwide standard for time. This makes the system’s screen where the word “Min” with the arrow pointing clock very accurate once the appropriate time zone and downward is displayed.
Page 249
UNDERSTANDING YOUR INSTRUMENT PANEL 249 Show Time if Radio is Off Changing the Time Zone When selected, this feature will display the time of day 1. Turn on the radio. on the touch screen when the radio is turned off. Proceed as follows to change the current setting: 2.
250 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RES — AM/FM STEREO RADIO Operating Instructions — Radio Mode WITH CD PLAYER (MP3 AUX JACK) NOTE: The ignition switch must be in the ON or ACC NOTE: The radio sales code is located on the lower right position to operate the radio.
Page 251
UNDERSTANDING YOUR INSTRUMENT PANEL 251 SEEK Buttons 4. Adjust the minutes using the right side TUNE/ Press and release the SEEK buttons to search for the next SCROLL control knob. Press the TUNE/SCROLL control listenable station in AM/FM mode. Press the right switch knob to save time change.
Page 252
252 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a second Push the rotary TUNE/SCROLL control knob again to time and MID will display. Turn the TUNE/SCROLL exit setting tone, balance, and fade. control knob to the right or left to increase or decrease the AM/FM Button mid-range tones.
UNDERSTANDING YOUR INSTRUMENT PANEL 253 SET 2 in both AM and FM. This allows a total of 12 AM Operation Instructions — CD MODE For CD And and 12 FM stations to be stored into pushbutton memory. MP3 Audio Play The stations stored in SET 2 memory can be selected by NOTE: pressing the pushbutton twice.
Page 254
254 UNDERSTANDING YOUR INSTRUMENT PANEL If you insert a disc with the ignition ON and the radio EJECT Button - Ejecting a CD ON, the unit will switch from radio to CD mode and Press the EJECT button to eject the CD. begin to play when you insert the disc.
UNDERSTANDING YOUR INSTRUMENT PANEL 255 TIME Button Press the RND button a second time to stop Random Press this button to change the display from a large CD Play. playing time display to a small CD playing time display. Notes on Playing MP3 Files RW/FF The radio can play MP3 files;...
Page 256
256 UNDERSTANDING YOUR INSTRUMENT PANEL The radio uses the following limits for file systems: Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal • Maximum number of folder levels: 8 CD audio tracks and computer files (including MP3 files). •...
Page 257
UNDERSTANDING YOUR INSTRUMENT PANEL 257 Playback of MP3 Files MPEG Sampling Fre- Bit Rate (kbps) When a medium containing MP3 data is loaded, the Specification quency (kHz) radio checks all files on the medium. If the medium 320, 256, 224, 192, contains a lot of folders or files, the radio will take more MPEG-1 Audio 160, 128, 112, 96,...
258 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - Auxiliary Mode SALES CODE RES/RSC — AM/FM STEREO The auxiliary (AUX) jack is an audio input jack, which RADIO WITH CD PLAYER (MP3 AUX JACK) AND allows the user to plug in a portable device, such as an SIRIUS RADIO MP3 player, or cassette player, and utilize the vehicle’s NOTE: The radio sales code is located on the lower right...
UNDERSTANDING YOUR INSTRUMENT PANEL 259 Operating Instructions — Radio Mode to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make NOTE: The ignition switch must be in the ON or ACC another selection.
Page 260
260 UNDERSTANDING YOUR INSTRUMENT PANEL Phone Button uconnect™ phone — If Equipped 3. After adjusting the hours, press the right side TUNE/ Press this button to operate the uconnect™ phone feature SCROLL control knob to set the minutes. The minutes (if equipped).
Page 261
UNDERSTANDING YOUR INSTRUMENT PANEL 261 INFO Button Push the rotary TUNE/SCROLL control knob a second Press the INFO button for an RDS station (one with call time and MID will display. Turn the TUNE/SCROLL letters displayed). The radio will return a Radio Text control knob to the right or left to increase or decrease the message broadcast from an FM station (FM mode only).
Page 262
262 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob again to Program Type 16-Digit Character Display exit setting tone, balance, and fade. College College MUSIC TYPE Button Country Country Pressing this button once will turn on the Music Type Foreign Language Language mode for five seconds.
Page 263
UNDERSTANDING YOUR INSTRUMENT PANEL 263 SETUP Button Program Type 16-Digit Character Display Pressing the SETUP button allows you to select between Soft Rhythm and Blues Soft R&B the following items: Sports Sports • Set Clock — Pressing the SELECT button will allow Talk Talk you to set the clock.
264 UNDERSTANDING YOUR INSTRUMENT PANEL window. Select the button (1–6) you wish to lock onto this Buttons 1 - 6 station and press and release that button. If a button is These buttons tune the radio to the stations that you not selected within five seconds after pressing the SET/ commit to pushbutton memory (12 AM and 12 FM RND button, the station will continue to play but will not...
Page 265
UNDERSTANDING YOUR INSTRUMENT PANEL 265 Inserting Compact Disc(s) CAUTION! (Continued) Gently insert one CD into the CD player with the CD • Do not use adhesive labels. These labels can peel label facing up. The CD will automatically be pulled into away and jam the player mechanism.
266 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Ejecting with the ignition OFF is not allowed on AM/FM Button convertible or soft-top models (if equipped). Press the button to select either AM or FM mode. SEEK Button SET/RND Button (Random Play Button) Press the right SEEK button for the next selection on the Press this button while the CD is playing to activate CD.
Page 267
UNDERSTANDING YOUR INSTRUMENT PANEL 267 Supported Media (Disc Types) a number instead. With a maximum number of files, The MP3 file recording media supported by the radio are exceeding 20 folders will result in this display. With CDDA, CD-R, CD-RW, MP3, and CDDA+MP3. 200 files, exceeding 50 folders will result in this display.) Supported Medium Formats (File Systems)
Page 268
268 UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats MPEG Specifi- Sampling Fre- Bit Rate (kbps) The radio will recognize only files with the *.MP3 exten- cation quency (kHz) sion as MP3 files. Non-MP3 files named with the *.MP3 320, 256, 224, 192, extension may cause playback problems.
UNDERSTANDING YOUR INSTRUMENT PANEL 269 Playback of MP3 Files LIST Button (CD Mode for MP3 Play) When a medium containing MP3 data is loaded, the Pressing the LIST button will bring up a list of all folders radio checks all files on the medium. If the medium on the disc.
270 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the INFO button again for three seconds TIME Button (Auxiliary Mode) to return to elapsed time display. Press this button to change the display to time of day. The time of day will display for five seconds (when the Operation Instructions - Auxiliary Mode ignition is OFF).
UNDERSTANDING YOUR INSTRUMENT PANEL 271 • Connecting an iPod to the AUX port located in the RER, REN, REP, REW or REZ touch-screen radio UCI feature, refer to the separate RER, REN or REZ User’s radio faceplate, plays media, but does not use the UCI Manual.
272 UNDERSTANDING YOUR INSTRUMENT PANEL • If the iPod battery is completely discharged, it may Once in the UCI (iPod ) mode, iPod audio tracks (if not communicate with the UCI system until a mini- available from iPod ) start playing over the vehicle’s mum charge is attained.
Page 273
UNDERSTANDING YOUR INSTRUMENT PANEL 273 • Jump backward in the current track by pressing and • While a track is playing, press the INFO button to see holding the << RW button. Holding the << RW the associated metadata (artist, track title, album, etc.) button long enough will take you to the beginning for that track.
274 UNDERSTANDING YOUR INSTRUMENT PANEL • During all List modes, the iPod displays all lists in Shuffle OFF modes for the iPod . If the RND icon is showing on the radio display, then the shuffle mode is “wrap-around” mode. So if the track is at the bottom of the list, just turn the wheel backwards (counter-clockwise) to get to the track faster.
Page 275
UNDERSTANDING YOUR INSTRUMENT PANEL 275 • To Exit List mode without selecting a track, press the CAUTION! same PRESET button again to go back to Play • Leaving the iPod (or any supported device) any- mode. where in the vehicle in extreme heat or cold can •...
276 UNDERSTANDING YOUR INSTRUMENT PANEL uconnect™ studios (SATELLITE RADIO) — IF information, call the toll-free number 888-539-7474, or EQUIPPED (REN/RER/RBZ/RES RADIOS ONLY) visit the Sirius web site at www.sirius.com, or at www- Satellite radio uses direct satellite-to-receiver broadcast- .siriuscanada.ca for Canadian residents. ing technology to provide clear digital sound, coast to Electronic Serial Number/Sirius Identification coast.
UNDERSTANDING YOUR INSTRUMENT PANEL 277 Sirius ID number will display. The Sirius ID number bikes should be placed as far rearward as possible, within display will time out in two minutes. Press any button on the loading design of the rack. Do not place items directly the radio to exit this screen.
278 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - uconnect™ studios INFO Button (Satellite) Mode Pressing the INFO button will cycle the display informa- tion between Artist, Song Title, and Composer (if avail- NOTE: The ignition switch must be in the ON or ACC able).
Page 279
UNDERSTANDING YOUR INSTRUMENT PANEL 279 MUSIC TYPE Button SETUP Button Pressing this button once will turn on the Music Type Pressing the SETUP button allows you to select the mode for five seconds. Pressing the MUSIC TYPE button following items: or turning the TUNE/SCROLL control knob within five •...
280 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second channel to each pushbutton by uconnect™ studios (SIRIUS BACKSEAT TV™) — repeating the above procedure with this exception: Press IF EQUIPPED the SET button twice and SET 2 will show in the display Satellite video uses direct satellite receiver broadcasting window.
UNDERSTANDING YOUR INSTRUMENT PANEL 281 • Ten different medias to choose from in each screen VIDEO ENTERTAINMENT SYSTEM (VES)™ — IF EQUIPPED (AM, FM, Sirius Radio, Sirius Backseat TV™, DVD1, The optional Video Entertainment System (VES)™ is DVD2, Hard Disc Drive (HDD), AUX in radio, AUX1, available with: AUX2) •...
282 UNDERSTANDING YOUR INSTRUMENT PANEL REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED VES™ Remote Control Location NOTE: Refer to the “uconnect™ studios” section of uconnect™ User Manual located on the DVD for further Remote Sound System Controls details. (Back View Of Steering Wheel) The remote sound system controls are located on the rear surface of the steering wheel, at the three and nine o’clock positions.
UNDERSTANDING YOUR INSTRUMENT PANEL 283 The right-hand rocker switch has a pushbutton in the The button located in the center of the left-hand switch center, and controls the volume and mode of the sound will tune to the next preset station that you have pro- system.
284 UNDERSTANDING YOUR INSTRUMENT PANEL CD/DVD MAINTENANCE NOTE: If you experience difficulty in playing a particu- To keep a CD/DVD in good condition, take the following lar disc, it may be damaged (i.e., scratched, reflective precautions: coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding.
UNDERSTANDING YOUR INSTRUMENT PANEL 285 Manual Heating and Air Conditioning System — If Front Blower Control Equipped There are four blower speeds. Use this The controls for the manual system in this vehicle contain control to regulate the amount of air a series of outer rotary dials and inner push knobs.
Page 286
286 UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control Mode Control (Air Direction) Use this control to regulate the tem- Mode control allows you to choose perature of the air inside the passenger from several selections of air distribu- compartment. Rotating the knob coun- tion.
Page 287
UNDERSTANDING YOUR INSTRUMENT PANEL 287 Bi-Level Mode Defrost Mode Air is directed through the panel and floor outlets. Air is directed through the windshield and side window demist outlets. Use DEFROST mode with maximum blower and temperature settings for best NOTE: There is a difference in temperature (in any windshield and side window defrosting.
Page 288
288 UNDERSTANDING YOUR INSTRUMENT PANEL • The A/C can be deselected manually without disturb- NOTE: • If the RECIRCULATION button is pressed when the ing the mode control selection. system is in MIX, DEFROST, or FLOOR mode the Economy Mode RECIRCULATION LED indicator will flash 3 times If ECONOMY mode is desired, press the A/C button to and then turn off to indicate RECIRCULATION mode...
UNDERSTANDING YOUR INSTRUMENT PANEL 289 Max A/C For maximum cooling use the A/C and RECIRCULA- TION mode buttons at the same time. Three-Zone Temperature Control — If Equipped With the Three-Zone Temperature Control System, each front seat occupant can independently control the Heat- ing, Ventilation, and Air Conditioning operations coming from the outlets on their side of the vehicle.
290 UNDERSTANDING YOUR INSTRUMENT PANEL The Three-Zone Temperature Control bottom panel con- The primary control for the rear blower is on the front trols rear Heating, Ventilation, and Air Conditioning climate control unit located on the instrument panel. operations. The Three-Zone Temperature Control bottom panel has five positions;...
Page 291
UNDERSTANDING YOUR INSTRUMENT PANEL 291 Only when the front control for the rear blower is in the RR position do the second row seat occupants have control of the rear blower speed. The rear blower control, located in the rear overhead console, has an off position and a range of blower speeds.
Page 292
292 UNDERSTANDING YOUR INSTRUMENT PANEL Rear Temperature Control control is in FLOOR, DEFROST, or MIX modes, airflow When the blower knob on the front climate control unit is will be directed out of the rear floor outlets. set to any position other than the rear temperature Rear Mode Control settings will be controlled by the rear temperature control knob on the front climate control unit.
UNDERSTANDING YOUR INSTRUMENT PANEL 293 Automatic Temperature Control (ATC) — If Equipped • Front Three-Zone ATC allows both driver and front passenger seat occupant, and rear seat occupants to select individual comfort settings. • Occupants in the vehicle select AUTO mode operation by a button press on the right rotary knob and a comfort temperature setting using rotary knobs on the control unit.
Page 294
294 UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Operation 1. Press the AUTO button on the Front Upper ATC Panel and the word AUTO will illuminate in the front ATC display, along with three temperatures for driver, front passenger, and rear seats. The system will then automati- cally regulate the amount of airflow.
Page 295
UNDERSTANDING YOUR INSTRUMENT PANEL 295 NOTE: Manual Operation • It is not necessary to move the temperature settings for This system offers a full complement of manual override cold or hot vehicles. The system automatically adjusts features. The AUTO symbol in the front ATC display will the temperature, mode and fan speed to provide be turned off when the system is being used in the comfort as quickly as possible.
Page 296
296 UNDERSTANDING YOUR INSTRUMENT PANEL Panel Mode Floor Mode Air is directed through the outlets in the instrument Air comes from the floor outlets. A slight amount of panel. These outlets can be adjusted for direction, air is directed through the defrost and side window and turned on or off to control airflow.
Page 297
UNDERSTANDING YOUR INSTRUMENT PANEL 297 The SNOWFLAKE mode, or A/C button, allows Recirculation Control the operator to manually activate or deactivate the When outside air contains smoke, odors, or air conditioning system. When in SNOWFLAKE high humidity, or if rapid cooling is desired, mode, and the ATC display is on cool, dehumidified air you may wish to recirculate interior air by flows through the air outlets.
Page 298
298 UNDERSTANDING YOUR INSTRUMENT PANEL Rear Automatic Temperature Control (ATC) — If Equipped The Rear ATC System has floor air outlets at the rear of the right side sliding door, and overhead outlets at each outboard rear seating position. The system provides heated air through the floor outlets or cool, dehumidified air through the headliner outlets.
Page 299
UNDERSTANDING YOUR INSTRUMENT PANEL 299 2. Rotate the Rear Blower, Rear Temperature and the customer-programmable feature. Refer to the “Elec- Rear Mode Control knobs to suit your comfort needs. tronic Vehicle Information Center (EVIC) — Customer- Programmable Features” in this Section. 3.
300 UNDERSTANDING YOUR INSTRUMENT PANEL Rear Temperature Control Bi-Level Mode To change the temperature in the rear of the vehicle, Air comes from both the headliner outlets and the rotate the temperature knob counterclockwise to lower floor outlets. the temperature, and clockwise to increase the tempera- NOTE: In many temperature positions, the BI-LEVEL ture.
UNDERSTANDING YOUR INSTRUMENT PANEL 301 Winter Operation Window Fogging To ensure the best possible heater and defroster perfor- Vehicle windows tend to fog on the inside in mild, rainy mance, make sure the engine cooling system is function- and/or humid weather. To clear the windows, select ing properly and the proper amount, type, and concen- DEFROST or MIX mode and increase the front blower tration of coolant is used.
302 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips A/C Air Filter— If Equipped On vehicles equipped with Automatic Temperature Con- trol (ATC), the climate control system filters out dust and pollen from the air. Refer to “Air Conditioning” in Sec- tion 7 of this manual for filter replacement instructions.
306 STARTING AND OPERATING STARTING PROCEDURES Automatic Transaxle Before starting your vehicle, adjust your seat, adjust the The shift lever must be in the NEUTRAL or PARK inside and outside mirrors, fasten your seat belt, and if position before you can start the engine. Press the brake present, instruct all other occupants to buckle their seat pedal before shifting into any driving gear.
STARTING AND OPERATING 307 NOTE: This vehicle is equipped with a transaxle shift WARNING! (Continued) interlocking system. The brake pedal must be pressed • Do not attempt to push or tow your vehicle to get to shift out of PARK. it started.
308 STARTING AND OPERATING After Starting CAUTION! The idle speed will automatically decrease as the engine warms up. To prevent damage to the starter, DO NOT crank the engine for more than 15–second intervals at one time. ENGINE BLOCK HEATER — IF EQUIPPED Wait 10 to 15 seconds before trying again.
STARTING AND OPERATING 309 AUTOMATIC TRANSAXLE WARNING! CAUTION! It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle Damage to the transaxle may occur if the following speed. If your foot is not firmly on the brake pedal, precautions are not observed: the vehicle could accelerate quickly forward or in •...
310 STARTING AND OPERATING Brake/Transaxle Interlock System This system prevents the key fob from being removed This vehicle is equipped with a Brake Transmission Shift unless the shift lever is in PARK. It also prevents moving Interlock System (BTSI) that holds the shift lever in the the shift lever out of PARK, unless the key fob is in the PARK position when the ignition switch is in the LOCK ACC/ON position, and the brake pedal is pressed.
STARTING AND OPERATING 311 The electronically-controlled transaxle provides a precise PARK shift schedule. The transaxle electronics are self- This range supplements the parking brake by locking the calibrating; therefore, the first few shifts on a new vehicle transaxle. The engine can be started in this gear. Never may be somewhat abrupt.
Page 312
312 STARTING AND OPERATING The following indicators should be used to ensure that WARNING! you have placed the shift lever into the PARK position: • Never use the PARK position as a substitute for • When moving the shift lever into PARK, press the the parking brake.
Page 313
STARTING AND OPERATING 313 REVERSE DRIVE — Six-Speed Transaxle This range is for moving the vehicle backward. Shift into This range should be used for most city and highway REVERSE only after the vehicle has come to a complete driving. It provides the smoothest upshifts, downshifts, stop.
Page 314
314 STARTING AND OPERATING heavy loading conditions, (i.e., in hilly terrain, traveling the transaxle into third gear, the transaxle will never shift into strong head winds or while towing heavy trailers). above third gear, but can shift down into second or first Under these conditions, using the “3”...
Page 315
STARTING AND OPERATING 315 Reset Mode - Electronic Transaxle Odometer The transaxle is monitored electronically for abnormal Screen conditions. If a condition is detected that could cause Display damage, the transaxle automatically shifts into second Actual gear (third gear for six-speed). The transaxle remains in Gear(s) second gear (third gear for six-speed) despite the forward Allowed...
316 STARTING AND OPERATING 5. Shift into the desired gear range and resume driving. WARNING! NOTE: Even if the transaxle can be reset, it is recom- Rapid acceleration on slippery surfaces is dangerous. mended that you visit an authorized dealer at your Unequal traction can cause sudden pulling of the earliest possible convenience.
STARTING AND OPERATING 317 2. Slow down if the road has standing water or puddles. Flowing/Rising Water 3. Replace the tires when tread wear indicators first WARNING! become visible. Do not drive on or across a road or path where water 4.
Page 318
318 STARTING AND OPERATING CAUTION! CAUTION! (Continued) • Driving through standing water may cause dam- • Always check the depth of the standing water age to your vehicle’s drivetrain components. Al- before driving through it. Never drive through ways inspect your vehicle’s fluids (i.e., engine oil, standing water that is deeper than the bottom of transmission/transaxle, axle, etc.) for signs of con- the tire rims mounted on the vehicle.
STARTING AND OPERATING 319 POWER STEERING WARNING! The standard power steering system will give you good • Driving through standing water limits your vehi- vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical cle’s traction capabilities. Do not exceed 5 mph steering capability if power assist is lost.
320 STARTING AND OPERATING system. This noise should be considered normal, and it checked if a leak is suspected, abnormal noises are does not in any way damage the steering system. apparent, and/or the system is not functioning as antici- pated.
STARTING AND OPERATING 321 If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to “Fluids, Lubricants, and Genuine Parts” in Section 7 for the correct fluid type. PARKING BRAKE When the parking brake is applied with the ignition switch ON, the “Brake Warning Light”...
322 STARTING AND OPERATING When parking on a hill, turn the front wheels toward the WARNING! curb on a downhill grade, and away from the curb on an • Always fully apply the parking brake when leav- uphill grade. ing your vehicle, or it may roll and cause damage The parking brake should always be applied whenever or injury.
Page 323
STARTING AND OPERATING 323 You may experience the following when the brake system WARNING! goes into anti-lock: • The Anti-Lock Brake System contains sophisti- • The ABS motor running (it may continue to run for a cated electronic equipment that may be susceptible short time after the stop) to interference caused by improperly installed, or •...
324 STARTING AND OPERATING come on when the ignition switch is turned to the ON WARNING! (Continued) position and may stay on for as long as four seconds. • The Anti-Lock Brake System cannot prevent acci- If the “Anti-Lock Brake Warning Light” remains on or dents, including those resulting from excessive comes on while driving, it indicates that the anti-lock speed in turns, following another vehicle too...
STARTING AND OPERATING 325 Brake Force Distribution (EBD) systems are not function- functions similarly to a limited-slip differential, and ing. Immediate repair to the ABS system is required. controls the wheel spin across a driven axle. If one wheel Consult with your authorized dealer service center as on a driven axle is spinning faster than the other, the soon as possible.
326 STARTING AND OPERATING application, and then applies optimum pressure to the WARNING! brakes. This can help reduce braking distances. The BAS • The TCS cannot prevent the natural laws of phys- complements the ABS. Applying the brakes very quickly results in the best BAS assistance.
STARTING AND OPERATING 327 ESC uses sensors in the vehicle to determine the vehicle WARNING! (Continued) path intended by the driver and compares it to the actual • The BAS cannot prevent accidents, including path of the vehicle. When the actual path does not match those resulting from excessive speed in turns, the intended path, ESC applies the brake of the appro- driving on very slippery surfaces, or hydroplan-...
Page 328
328 STARTING AND OPERATING several ignition cycles, and the vehicle has been driven WARNING! (Continued) several miles (kilometers) at speeds greater than 30 mph • ESC cannot prevent accidents, including those (48 km/h), see your authorized dealer as soon as possible resulting from excessive speed in turns, driving on to have the problem diagnosed and corrected.
Page 329
STARTING AND OPERATING 329 • The ESC system will make buzzing or clicking sounds When in the “Partial Off” mode, the TCS portion of ESC, when it is active. This is normal; the sounds will stop except for the “limited slip” feature described in the TCS when ESC becomes inactive following the maneuver section, has been disabled and the “ESP Off Indicator that caused the ESC activation.
330 STARTING AND OPERATING TIRE SAFETY INFORMATION NOTE: • P (Passenger) - Metric tire sizing is based on U.S. Tire Markings design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. •...
Page 331
STARTING AND OPERATING 331 • High flotation tire sizing is based on U.S. design Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designa- standards and it begins with the tire diameter molded tion.
Page 332
332 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
STARTING AND OPERATING 333 Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall The TIN may be found on one or both sides of the tire, tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side.
334 STARTING AND OPERATING Tire Loading and Tire Pressure This placard tells you important information about the: Tire Placard Location 1) number of people that can be carried in the vehicle NOTE: The proper cold tire inflation pressure is listed 2) total weight your vehicle can carry on the driver’s side B-Pillar.
Page 335
STARTING AND OPERATING 335 NOTE: Under a maximum loaded vehicle condition, Steps for Determining Correct Load Limit gross axle weight ratings (GAWRs) for the front and rear 1. Locate the statement “The combined weight of occu- axles must not be exceeded. For further information on pants and cargo should never exceed XXX lbs or XXX kg”...
Page 336
336 STARTING AND OPERATING 5. Determine the combined weight of luggage and cargo NOTE: • The following table shows examples on how to calcu- being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity late total load, cargo/luggage, and towing capacities calculated in Step 4.
338 STARTING AND OPERATING Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause accidents. recommended load capacity for your vehicle.
Page 339
STARTING AND OPERATING 339 Tire Inflation Pressures WARNING! (Continued) The proper cold tire inflation pressure is listed on the • Unequal tire pressures from one side of the ve- driver’s side “B” Pillar. hicle to the other can cause the vehicle to drift to The tire pressure should be checked and adjusted, and the right or left.
Page 340
340 STARTING AND OPERATING Inflation pressures specified on the placard are always Example: If garage temperature is 68°F (20°C) and the “cold tire inflation pressure.” Cold tire inflation pressure outside temperature is 32°F (0°C), then the cold tire is defined as the tire pressure after the vehicle has not inflation pressure should be increased by 3 psi (21 kPa), been driven for at least three hours, or driven less than which equals 1 psi (7 kPa) for every 12°F (7°C) for this...
Page 341
STARTING AND OPERATING 341 Cuts and punctures in radial tires are repairable only in WARNING! the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs. High-speed driving, with your vehicle at or above maximum load, is dangerous. The added strain on Compact Spare Tire your tires could cause them to fail.
Page 342
342 STARTING AND OPERATING WARNING! CAUTION! • Temporary-use spare tires are for emergency use Because of the reduced ground clearance, do not take only. With these tires, do not drive faster than your vehicle through an automatic car wash with the 50 mph (80 km/h).
Page 343
STARTING AND OPERATING 343 WARNING! • Fast spinning tires can be dangerous. Forces gen- erated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. • Do not spin your vehicle’s wheels faster than 30 mph (48 km/h), or for more than 30 seconds continuously, when you are stuck;...
Page 344
344 STARTING AND OPERATING Tire Life Replacement Tires The service life of a tire is dependent upon varying The tires on your new vehicle provide a balance of many factors, including, but not limited to: characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure.
STARTING AND OPERATING 345 WARNING! WARNING! (Continued) • Failure to equip your vehicle with tires having • Do not use a tire, wheel size or rating other than adequate speed capability can result in sudden tire that specified for your vehicle. Some combinations failure and loss of vehicle control.
Page 346
346 STARTING AND OPERATING CAUTION! CAUTION! (Continued) • Install chains on the front wheels as tightly as To avoid damage to your vehicle or tires, observe the possible and then retighten after driving about following precautions: 0.5 mile (0.8 km). •...
STARTING AND OPERATING 347 SNOW TIRES TIRE ROTATION RECOMMENDATIONS Some areas of the country require the use of snow tires Tires on the front and rear axles of vehicles operate at during Winter. Standard tires are of the all-season type different loads and perform different steering, driving, and satisfy this requirement as indicated by the M+S and braking functions.
348 STARTING AND OPERATING The suggested rotation method is shown in the following found on the tire placard located on the driver’s-side diagram. B-pillar. The tire pressure will vary with temperature by about 1 psi (6.9 kPa) for every 12°F (6.5°C). This means that when the outside temperature decreases, the tire pressure will decrease.
Page 349
STARTING AND OPERATING 349 The TPMS will continue to warn the driver of low tire Warning Light.” Driving the vehicle may cause the tire pressure as long as the condition exists, and will not turn pressure to rise to approximately 30 psi (207 kPa), but the off until the tire pressure is at or above recommended “TPMS Warning Light”...
350 STARTING AND OPERATING • The TPMS is not a substitute for proper tire mainte- CAUTION! (Continued) nance, and it is the driver’s responsibility to maintain • After inspecting or adjusting the tire pressure correct tire pressure, using an accurate tire pressure always reinstall the valve stem cap.
Page 351
STARTING AND OPERATING 351 The Basic TPMS consists of the following components: NOTE: The vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) to receive this • Receiver Module information. • Four Tire Pressure Monitoring Sensors The “TPMS Warning Lamp”...
352 STARTING AND OPERATING 3. Accumulation of excessive snow and/or ice around 4. For each subsequent ignition switch cycle, a chime will the wheels or wheel housings. sound and the “TPMS Telltale Warning Light” will re- main on solid. 4. Using tire chains on the vehicle. 5.
Page 353
STARTING AND OPERATING 353 NOTE: It is particularly important to regularly check pressures are low. In addition, the EVIC will display a and maintain proper tire pressure in all the tires. Low Pressure message for three seconds and a graphic display of the pressure value(s) with the low tire(s) The Premium TPMS consists of the following compo- flashing.
Page 354
354 STARTING AND OPERATING Should a low tire condition occur on any of the four active road tire(s), you should stop as soon as possible, and inflate the low tire(s) that is flashing on the graphic display to the vehicle’s recommended cold tire pressure value.
Page 355
STARTING AND OPERATING 355 will not be present, and a pressure value will be dis- 2. If you install the compact spare tire in place of a road played instead of dashes. A system fault can occur by any tire that has a pressure below the low-pressure warning of the following scenarios: limit, upon the next ignition switch cycle, the “TPMS Telltale Warning Light”...
356 STARTING AND OPERATING • This device must accept any interference received, 5. Once you repair or replace the original road tire, and reinstall it on the vehicle in place of the compact spare, including interference that may cause undesired the TPMS will update automatically.
STARTING AND OPERATING 357 4.0L Engine Over 40 automobile manufacturers around the world The 4.0L engine is designed to meet all have issued and endorsed consistent gasoline specifica- emissions regulations and provide satisfac- tions (the World Wide Fuel Charter, WWFC) to define tory fuel economy and performance when fuel properties necessary to deliver enhanced emissions, using high-quality unleaded gasoline hav-...
358 STARTING AND OPERATING Gasoline/Oxygenate Blends E-85 Usage In Non-Flex Fuel Vehicles Some fuel suppliers blend unleaded gasoline with oxy- Non-FFV vehicles are compatible with gasoline contain- genates such as 10% ethanol, MTBE, and ETBE. Oxygen- ing 10% ethanol (E10). Gasoline with higher ethanol ates are required in some areas of the country during the content may void the vehicle’s warranty.
STARTING AND OPERATING 359 • disconnect and reconnect the battery to reset the It is even more important to look for gasolines without engine controller memory MMT in Canada, because MMT can be used at levels higher than those allowed in the United States. More extensive repairs will be required for prolonged exposure to E-85 fuel.
360 STARTING AND OPERATING Fuel System Cautions CAUTION! (Continued) • The use of fuel additives which are now being CAUTION! sold as octane enhancers is not recommended. Follow these guidelines to maintain your vehicle’s Most of these products contain high concentra- performance: tions of methanol.
STARTING AND OPERATING 361 Carbon Monoxide Warnings WARNING! (Continued) • Guard against carbon monoxide with proper WARNING! maintenance. Have the exhaust system inspected Carbon monoxide (CO) in exhaust gases is deadly. every time the vehicle is raised. Have any abnor- •...
Page 362
362 STARTING AND OPERATING the other sections of this manual for information on CAUTION! features that are common between Flexible Fuel and gasoline only powered vehicles. Only vehicles with the E-85 fuel filler door label can operate on E-85. E-85 Fuel Cap E-85 Badge...
STARTING AND OPERATING 363 Ethanol Fuel (E-85) For best results, a refueling pattern that avoids alternat- E-85 is a mixture of approximately 85% fuel ethanol and ing between E-85 and unleaded gasoline is recom- 15% unleaded gasoline. mended. When you do switch fuel types, it is recommended that: WARNING! •...
32°F (0°C). in MOPAR engine oils, and in equivalent oils meeting Cruising Range Chrysler Specification MS-6395. The manufacturer only Because E-85 fuel contains less energy per gallon/liter recommends engine oils that are API Certified and meet than gasoline, you will experience an increase in fuel the requirements of Material Standard MS-6395.
STARTING AND OPERATING 365 Replacement Parts ADDING FUEL Many components in your Flexible Fuel Vehicle (FFV) are Fuel Filler Cap (Gas Cap) designed to be compatible with ethanol. Always be sure The gas cap is located behind the fuel filler door on the that your vehicle is serviced with correct ethanol com- left side of the vehicle.
Page 366
366 STARTING AND OPERATING CAUTION! WARNING! (Continued) • Never add fuel when the engine is running. This is • Damage to the fuel system or emissions control in violation of most state and federal fire regula- system could result from using an improper fuel tions and will cause the MIL to turn on.
STARTING AND OPERATING 367 Loose Fuel Filler Cap Message If seats are removed for carrying cargo, do not exceed the If the vehicle diagnostic system determines that the fuel specified GVWR and GAWR. filler cap is loose, improperly installed, or damaged, a Vehicle Certification Label “gASCAP”...
Page 368
368 STARTING AND OPERATING The bar code allows a computer scanner to read the WARNING! Vehicle Identification Number (VIN). Because the front wheels drive and steer the vehicle, Gross Vehicle Weight Rating (GVWR) it is important that you do not exceed the maximum The GVWR is the total allowable weight of your vehicle.
Page 369
STARTING AND OPERATING 369 Curb Weight Figure out the weight on the front and rear of the vehicle The curb weight of a vehicle is defined as the total weight separately. It is important that you distribute the load of the vehicle with all fluids, including vehicle fuel, at full evenly over the front and rear axles.
Page 370
370 STARTING AND OPERATING CAUTION! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control.
STARTING AND OPERATING 371 TRAILER TOWING LOADING TABLE — EXAMPLE ONLY In this section you will find safety tips and information Front Axle Rear Axle on limits to the type of towing you can reasonably do TOTAL 2,500 lbs 2,450 lbs with your vehicle.
Page 372
372 STARTING AND OPERATING Gross Trailer Weight (GTW) WARNING! The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or tem- It is important that you do not exceed the maximum porary) loaded in or on the trailer in its loaded and front or rear GAWR.
Page 373
STARTING AND OPERATING 373 that typically provides adjustable friction associated with also dampens sway caused by traffic and crosswinds and the telescoping motion to dampen any unwanted trailer contributes positively to tow vehicle and trailer stability. swaying motions while traveling. Trailer sway control and a weight distributing (load equalizing) hitch are recommended for heavier tongue Weight-Carrying Hitch...
Page 374
374 STARTING AND OPERATING Without Weight-Distributing Hitch (Incorrect) With Weight-Distributing Hitch (Correct)
Page 375
STARTING AND OPERATING 375 The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow, and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. TRAILER HITCH CLASSIFICATIONS Max.
Page 376
376 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. GCWR (Gross Max. GTW Engine/Transaxle Combined Wt. Rat- Frontal Area Max. Tongue Wt. (Gross Trailer Wt.) ing) Up to 2 persons &...
Page 377
STARTING AND OPERATING 377 GCWR (Gross Max. GTW Engine/Transaxle Combined Wt. Rat- Frontal Area Max. Tongue Wt. (Gross Trailer Wt.) ing) Up to 2 persons & Luggage 9,000 lbs (4 082 kg) 40 sq ft (3.72 sq m) 380 lbs (172 kg) 3,800 lbs (1 723 kg)* 3.8L and 4.0L/ 3 to 5 persons &...
Page 378
378 STARTING AND OPERATING Never exceed the maximum trailer tongue weight Consider the following items when computing the stamped on your bumper or trailer hitch. weight on the rear axle of the vehicle: • The tongue weight of the trailer. •...
Page 379
STARTING AND OPERATING 379 Towing Requirements WARNING! To promote proper break-in of your new vehicle drive- train components, the following guidelines are recom- Improper towing can lead to an injury accident. mended: Follow these guidelines to make your trailer towing as safe as possible: CAUTION! •...
Page 380
380 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Safety chains must always be used between your 3. GAWR vehicle and trailer. Always connect the chains to 4. Trailer tongue weight rating for that trailer hitch. the frame or hook retainers of the vehicle hitch. (This requirement may limit the ability to always Cross the chains under the trailer tongue and achieve the 10% to 15% range of trailer tongue weight...
Page 381
STARTING AND OPERATING 381 • Check for signs of tire wear or visible tire damage actuated brakes. When towing a trailer equipped with before towing a trailer. Refer to “Tires–General Infor- a hydraulic surge actuated brake system, an electronic mation” in this section for the proper inspection brake controller is not required.
Page 382
382 STARTING AND OPERATING Towing Requirements — Trailer Lights and Wiring WARNING! Whenever you pull a trailer, regardless of the trailer size, • Do not connect trailer brakes to your vehicle’s stop lights and turn signals on the trailer are required for motoring safety.
Page 383
STARTING AND OPERATING 383 Four-Pin Connector Seven-Pin Connector 1 — Female Pins 4 — Park 1 — Battery 5 — Ground 2 — Male Pin 5 — Left Stop/Turn 3 — Ground 6 — Right Stop/Turn 2 — Backup Lamps 6 —...
384 STARTING AND OPERATING Towing Tips 45 minutes of continuous operation. Refer to the “Main- Before setting out on a trip, practice turning, stopping tenance Schedule” in Section 8 for the proper mainte- and backing the trailer in an area away from heavy nance intervals.
STARTING AND OPERATING 385 Cooling System RECREATIONAL TOWING To reduce potential for engine and transaxle overheating, (BEHIND MOTORHOME, ETC.) take the following actions: CAUTION! • City Driving When stopped for short periods of time, put the shift Towing this vehicle behind another vehicle (flat- lever in NEUTRAL but do not increase engine idle speed.
388 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located in the In any of the following situations, you can reduce the center of the instrument panel above the radio. potential for overheating by taking the appropriate action.
WHAT TO DO IN EMERGENCIES 389 JACKING AND TIRE CHANGING CAUTION! WARNING! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads “H”, pull • Getting under a jacked-up vehicle is dangerous. over and stop the vehicle. Idle the vehicle with the air The vehicle could slip off the jack and fall on you.
390 WHAT TO DO IN EMERGENCIES Jack Location Spare Tire Removal The jack, jack handle and winch handle tools are stowed The spare tire is stowed inside a protective cover located behind the rear left side trim panel in the rear cargo area. under the center of the vehicle by means of a cable winch Turn the two cover latches to release the cover.
WHAT TO DO IN EMERGENCIES 391 Preparations For Jacking 1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.
392 WHAT TO DO IN EMERGENCIES 6. Block both the front and rear of the WARNING! (Continued) wheel diagonally opposite the jacking • Always park on a firm, level surface as far from position. For example, if changing the the edge of the roadway as possible before raising right front tire, block the left rear the vehicle.
Page 393
WHAT TO DO IN EMERGENCIES 393 2. To remove the compact spare tire/cover assembly, WARNING! (Continued) assemble the winch handle extensions to form a “T’ and • If working on or near a roadway, be extremely fit the winch “T” handle over the drive nut. Rotate the careful of motor traffic.
Page 394
394 WHAT TO DO IN EMERGENCIES WARNING! Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift.
Page 395
WHAT TO DO IN EMERGENCIES 395 5. There are two jack engagement locations on each side of the vehicle body. These locations are on the sill flange of the vehicle body. NOTE: • Rear jack locations are between a pair of down-facing tabs on the sill flange of the vehicle side body.
Page 396
396 WHAT TO DO IN EMERGENCIES Jack Location...
Page 397
WHAT TO DO IN EMERGENCIES 397 CAUTION! WARNING! Do not attempt to raise the vehicle by jacking on Raising the vehicle higher than necessary can make locations other than those indicated in Step 5. the vehicle less stable. It could slip off the jack and hurt someone near it.
Page 398
398 WHAT TO DO IN EMERGENCIES 10. Lower the vehicle by turning the jack screw to the 13. Place the deflated (flat) tire and compact spare tire left. cover assembly. in the rear cargo area. Do not stow the deflated tire in the spare tire location. Have the full- 11.
WHAT TO DO IN EMERGENCIES 399 Wheel Nuts turning freely. This will allow enough slack in the cable to All wheel nuts should be tightened occasionally, to allow you to pull the wheel spacer out from under the eliminate the possibility of wheel studs being sheared or vehicle.
Page 400
400 WHAT TO DO IN EMERGENCIES 2. Assemble the winch handle extensions to form the WARNING! spare tire hook, and pull the wheel spacer from under the vehicle. Verify that both retainer tabs of the wheel spacer have been properly extended through the center of 3.
WHAT TO DO IN EMERGENCIES 401 CAUTION! WARNING! • Take care to avoid the radiator cooling fan when- The winch mechanism is designed specifically to stow a compact spare tire only. Do not attempt to use ever the hood is raised. It can start anytime the the winch to stow the full size flat tire, or any other ignition switch is on.
Page 402
402 WHAT TO DO IN EMERGENCIES the automatic transmission shift lever into PARK and WARNING! (Continued) turn the ignition switch to the OFF position for both • A battery generates hydrogen gas which is flam- vehicles. mable and explosive. Keep flame or spark away from the vent holes.
Page 403
WHAT TO DO IN EMERGENCIES 403 5. Connect the other cable, first to the negative terminal 6. Start the engine in the vehicle that has the booster of the booster battery, and then to the engine of the battery. Let the engine idle a few minutes, then start the vehicle with the discharged battery.
404 WHAT TO DO IN EMERGENCIES CAUTION! CAUTION! • When “rocking” a stuck vehicle by moving be- Any procedure other than above could result in damage to the charging system of the booster vehicle tween 1st and REVERSE, do not spin the wheels or of the immobilized vehicle.
WHAT TO DO IN EMERGENCIES 405 • The towing speed must not exceed 44 mph (72 km/h). WARNING! CAUTION! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause damage, or Exceeding these towing limits may cause a transmis- even failure, of the axle and tires.
Page 406
406 WHAT TO DO IN EMERGENCIES Towing Without The Ignition Key CAUTION! (Continued) Special care must be taken when the vehicle is towed • Do not tow the vehicle from the rear. Damage to with the ignition in the OFF position. The only approved the rear sheet metal, liftgate and fascia will occur.
MAINTAINING YOUR VEHICLE 411 ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard • Prolonged driving with the MIL on could cause diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic further damage to the emission control system.
412 MAINTAINING YOUR VEHICLE this manual. Tighten the gas cap until a clicking sound Indicator Light (MIL)” is functioning and is not on when is heard. This is an indication that the gas cap is properly the engine is running, and that the OBD II system is tightened.
MAINTAINING YOUR VEHICLE 413 4. As soon as you turn the ignition switch to the ON you may need to do nothing more than drive your position, you will see the MIL symbol come on as part of vehicle as you normally would in order for your OBD II a normal bulb check.
Only do service work for which you mance. Immediately have potential malfunctions have the knowledge and the proper equipment. If examined by an authorized Chrysler Group LLC you have any doubt about your ability to perform a dealership or qualified repair center.
MAINTAINING YOUR VEHICLE 415 Engine Oil CAUTION! (Continued) Checking Oil Level • Your vehicle has been built with improved fluids To assure proper engine lubrication, the engine oil must that protect the performance and durability of be maintained at the correct level. Check the oil level at your vehicle and also allow extended maintenance regular intervals, such as every fuel stop.
Page 416
Engine Oil Selection not covered by the New Vehicle Limited Warranty. For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends engine oils that are API certified and meet the requirements of Chrysler Material Standard MS-6395.
Page 417
MAINTAINING YOUR VEHICLE 417 Engine Oil Viscosity (SAE Grade) — 3.3L & 3.8L For information on engine oil filler cap location, refer to Gasoline Engines “Engine Compartment” in this section. SAE 5W-20 engine oil is recommended for all operating Lubricants that do not have both the engine oil certifica- temperatures.
418 MAINTAINING YOUR VEHICLE Disposing of Used Engine Oil and Oil Filters Engine Air Cleaner Filter Care should be taken in disposing of used engine oil and Refer to the “Maintenance Schedule” in Section 8 for the oil filters from your vehicle. Used oil and oil filters, proper maintenance intervals.
MAINTAINING YOUR VEHICLE 419 Engine Air Cleaner Filter Selection inspect the exhaust system each time the vehicle is raised The quality of replacement engine air cleaner filters varies for lubrication or oil change. Replace as required. considerably. Only high quality filters should be used to WARNING! assure most efficient service.
Page 420
420 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- NOTE: Intentional tampering with emissions control verter will not require maintenance. However, it is im- systems can result in civil penalties being assessed portant to keep the engine properly tuned to assure against you.
MAINTAINING YOUR VEHICLE 421 To minimize the possibility of catalyst damage: WARNING! • Do not shut OFF the engine or interrupt the ignition • Battery fluid is a corrosive acid solution and can when the transaxle is in gear and the vehicle is in burn or even blind you.
422 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance CAUTION! For best possible performance, your air conditioner • It is essential when replacing the cables on the should be checked and serviced by an authorized dealer at the start of each warm season. This service should battery that the positive cable is attached to the include cleaning of the condenser fins and a system positive post and the negative cable is attached to...
Page 423
MAINTAINING YOUR VEHICLE 423 Refrigerant Recovery and Recycling WARNING! R-134a air conditioning refrigerant is a hydrofluoro- • Use only refrigerants and compressor lubricants carbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. How- approved by the manufacturer for your air condi- ever, the manufacturer recommends that air conditioning tioning system.
Page 424
424 MAINTAINING YOUR VEHICLE WARNING! Do not remove the A/C air filter while the blower is operating or personal injury may result. The A/C air filter is located in the fresh air inlet behind the glove box. Perform the following procedure to re- place the filter: 1.
MAINTAINING YOUR VEHICLE 425 hood latching components to ensure proper function. CAUTION! When performing other underhood services, the hood latch, release mechanism and safety catch should be The A/C air filter is labeled with an arrow to indicate cleaned and lubricated. airflow direction through the filter.
Page 426
426 MAINTAINING YOUR VEHICLE Avoid using the wiper blades to remove frost or ice from The washer fluid reservoir will hold a full gallon of fluid the windshield. Keep the blade rubber out of contact with when the Low Washer Fluid Light illuminates. petroleum products such as engine oil, gasoline, etc.
MAINTAINING YOUR VEHICLE 427 Cooling System rusty in appearance, the system should be drained, flushed and refilled with fresh coolant. Check the front of WARNING! the A/C condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden •...
Page 428
428 MAINTAINING YOUR VEHICLE Cooling System — Drain, Flush and Refill CAUTION! If the engine coolant (antifreeze) is dirty or contains a • Mixing of engine coolant (antifreeze) other than considerable amount of sediment, clean and flush with a specified Hybrid Organic Additive Technology reliable cooling system cleaner.
Page 429
MAINTAINING YOUR VEHICLE 429 Adding Coolant Use only high purity water such as distilled or deionized Your vehicle has been built with an improved engine water when mixing the water/engine coolant (antifreeze) coolant (antifreeze) that allows extended maintenance solution. The use of lower quality water will reduce the intervals.
Page 430
430 MAINTAINING YOUR VEHICLE The cap should be inspected and cleaned if there is any Disposal of Used Coolant accumulation of foreign material on the sealing surfaces. Used ethylene glycol-based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check WARNING! with your local authorities to determine the disposal rules for your community.
Page 431
MAINTAINING YOUR VEHICLE 431 The radiator normally remains completely full, so there is If an examination of your engine compartment shows no no need to remove the radiator cap unless checking for evidence of radiator or hose leaks, the vehicle may be engine coolant (antifreeze) freeze point or replacing the safely driven.
432 MAINTAINING YOUR VEHICLE • Make sure that the radiator and coolant recovery WARNING! bottle overflow hoses are not kinked or obstructed. Riding the brakes can lead to brake failure and • Keep the front of the radiator clean. If your vehicle is possibly an accident.
Page 433
MAINTAINING YOUR VEHICLE 433 Add enough fluid to bring the level up to the require- WARNING! (Continued) ments described on the brake fluid reservoir. With disc • To avoid contamination from foreign matter or brakes, fluid level can be expected to fall as the brake moisture, use only new brake fluid or fluid that pads wear.
434 MAINTAINING YOUR VEHICLE All six–speed transaxles are equipped with a capped WARNING! (Continued) dipstick tube. It is sealed and should not be tampered • Do not allow petroleum based fluid to contami- with. Your authorized dealer has the necessary tools to nate the brake fluid.
Page 435
MAINTAINING YOUR VEHICLE 435 Fluid Level Check — 3.3L Engine with Four-Speed CAUTION! Automatic Transaxle — If Equipped The dipstick is located just behind the radiator on the Using a transmission fluid other than the manufac- lower right side. turer’s recommended fluid may cause deterioration in transaxle shift quality and/or torque converter To properly check the automatic transaxle fluid level, the shudder.
Page 436
436 MAINTAINING YOUR VEHICLE 5. Remove the dipstick and determine if the fluid is hot CAUTION! or warm. Hot fluid is approximately 180°F (82°C), which is the normal operating temperature after the vehicle has Do not overfill. Dirt and water in the transaxle can been driven at least 15 miles (24 km).
MAINTAINING YOUR VEHICLE 437 the use of special dyes to aid in detecting fluid leaks. In road surfaces on which the vehicle is operated, extreme addition, avoid using transaxle sealers as they may hot or cold weather and other extreme conditions will adversely affect seals.
Page 438
438 MAINTAINING YOUR VEHICLE Washing CAUTION! • Wash your vehicle regularly. Always wash your ve- Do not use abrasive or strong cleaning materials such hicle in the shade using MOPAR Car Wash or equiva- as steel wool or scouring powder, which will scratch lent, or a mild car wash soap, and rinse the panels metal and painted surfaces.
Page 439
MAINTAINING YOUR VEHICLE 439 coating, have your vehicle repaired as soon as pos- non-acidic cleaner. Do not use scouring pads, steel wool, sible. The cost of such repairs is considered the respon- a bristle brush, or metal polishes. Only MOPAR sibility of the owner.
Page 440
440 MAINTAINING YOUR VEHICLE • For grease stains, apply MOPAR Multi-Purpose if absolutely necessary. Do not use harsh cleaners or Cleaner or a equivalent high quality cleaner to a clean, Armorall. Use MOPAR Total Clean or equivalent to damp cloth and remove the stain. Use a fresh, damp clean vinyl upholstery towel to remove soap residue.
Page 441
MAINTAINING YOUR VEHICLE 441 Glass Surfaces WARNING! All glass surfaces should be cleaned on a regular basis with MOPAR Glass Cleaner or equivalent or any com- Do not use volatile solvents for cleaning purposes. mercial household-type glass cleaner. Never use an abra- Many are potentially flammable, and if used in sive type cleaner.
442 MAINTAINING YOUR VEHICLE 1. Clean with a wet soft rag. A mild soap solution may be Cleaning the Instrument Panel Cupholders used, but do not use high alcohol content or abrasive Removal cleaners. If soap is used, wipe clean with a clean damp Pull the flexible liner from the cupholder drawer starting rag.
MAINTAINING YOUR VEHICLE 443 Installation CAUTION! Place the liner into the cupholder drawer and press the • When installing the Totally Integrated Power liner into place so that the retention tabs seat into the corresponding openings in the drawer. Module cover, it is important to ensure the cover is properly positioned and fully latched.
Page 444
444 MAINTAINING YOUR VEHICLE The numbers inside the TIPM cover correspond to the FUSES/TIPM following table. Cav- Cartridge Mini-Fuse Description FUSES/TIPM Fuse Cav- Cartridge 30 Amp — Anti-Lock Brake Sys- Mini-Fuse Description Fuse Pink tem (ABS) Valve/ESP 40 Amp — Power Folding Seat 40 Amp —...
Page 445
MAINTAINING YOUR VEHICLE 445 FUSES/TIPM FUSES/TIPM Cav- Cartridge Cav- Cartridge Mini-Fuse Description Mini-Fuse Description Fuse Fuse 30 Amp — Rear Blower — 15 Amp Center High Pink Blue Mounted Stop Light (CHMSL)/Brake 40 Amp — Starter Solenoid Switch Green — —...
Page 446
446 MAINTAINING YOUR VEHICLE FUSES/TIPM FUSES/TIPM Cav- Cartridge Cav- Cartridge Mini-Fuse Description Mini-Fuse Description Fuse Fuse — 20 Amp Power Outlet #2 — 15 Amp Ignition Off Draw — Yellow (BATT/ACC SE- Blue Vehicle Entertainment LECT) System (IOD-VES), — 20 Amp Front Heated Seat Satellite Digital Au- Yellow...
MAINTAINING YOUR VEHICLE 451 are fused with self-resetting fuses that are only service- FUSES/TIPM able by an authorized dealer. The power seats are fused Cav- Cartridge Mini-Fuse Description by a 30 Amp circuit breaker located under the driver’s Fuse seat. The power windows are fused by a 25 Amp circuit —...
452 MAINTAINING YOUR VEHICLE • Anytime you store your vehicle, or keep it out of NOTE: For lighted switches, see your authorized dealer service for two weeks or more, run the air conditioning for replacement instructions. system at idle for about five minutes in the fresh air All of the interior bulbs are glass wedge base or glass and high blower setting.
MAINTAINING YOUR VEHICLE 453 BULB REPLACEMENT 5. Connect the wiring connector to bulb and slide red lock tab forward. Headlamps Front Park/Turn Signal Lamps 1. Raise the hood to access the rear of the headlamp housing. 1. Raise the hood to access the rear of the headlamp housing.
454 MAINTAINING YOUR VEHICLE CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. 2. Disconnect the wire harness from the bulb. 3.
MAINTAINING YOUR VEHICLE 455 Center High-Mounted Stop Lamp (CHMSL) The CHMSL uses LED lamps that are not serviceable separately. The CHMSL must be replaced as an assembly. See your authorized dealer. License Lamp The license plate lamp is located under the tailgate light bar and above the license plate.
Use API Certified SAE 5W-20 Engine Oil, meeting the requirements Engine Oil (3.3L and 3.8L Engines) of Chrysler Material Standard MS-6395. Refer to your oil filler cap for correct SAE grade. Use API Certified SAE 10W-30 Engine Oil, meeting the requirements Engine Oil (4.0L Engine)
458 MAINTAINING YOUR VEHICLE Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transaxle MOPAR ATF+4 Automatic Transmission Fluid or equivalent. MOPAR DOT 3 and SAE J1703 should be used or equivalent. If Brake Master Cylinder DOT 3 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids.
Page 459
MAINTENANCE SCHEDULES CONTENTS Emissions Control System Maintenance ..460 Maintenance Schedule ....460 ▫ Required Maintenance Intervals ..462...
Page 460
460 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE MAINTENANCE SCHEDULE The Scheduled Maintenance services listed in bold type The oil change indicator system will remind you that it is must be done at the times or mileages specified to ensure time to take your vehicle in for scheduled maintenance. the continued proper functioning of the emissions control On Non-EVIC equipped vehicles, CHAngE OIL will system.
Page 461
MAINTENANCE SCHEDULES 461 NOTE: Your authorized dealer will reset the oil change indicator • The oil change indicator message will not monitor the message after completing the scheduled oil change. If this time since the last oil change. Change your vehicle’s scheduled oil change is performed by someone other oil if it has been six months since your last oil change, than your dealer, the message can be reset by referring to...
Page 462
462 MAINTENANCE SCHEDULES Once A Month At Each Oil Change • Check tire pressure and look for unusual wear or • Change the engine oil filter. damage. • Inspect the brake hoses and lines. • Inspect the battery and clean and tighten the terminals CAUTION! as required.
Page 463
❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 465
❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 466
❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 467
❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 468
❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 469
❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 470
❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 471
❏ Replace the timing belt (4.0L engine). ❏ Flush and replace the engine coolant if not done at 60 months. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 472
❏ Replace accessory drive belt(s). ❏ Change the automatic transaxle fluid & filter. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 473
❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 474
474 MAINTENANCE SCHEDULES 138,000 Miles (230,000 km) or 138 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer...
Page 475
❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 476
476 MAINTENANCE SCHEDULES † This maintenance is recommended by the manufac- turer, but is not required to maintain emissions warranty. WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment.
If You Need Assistance ....479 Reporting Safety Defects ....482 ▫ Chrysler Group LLC Customer Center ..480 ▫ In The 50 United States And Washington, D.C.
Page 478
478 IF YOU NEED CONSUMER ASSISTANCE ▫ Traction Grades ..... 485 Department Of Transportation Uniform Tire Quality Grades ......485 ▫...
IF YOU NEED CONSUMER ASSISTANCE 479 SUGGESTIONS FOR OBTAINING SERVICE FOR the service advisor and list the items in order of priority. YOUR VEHICLE At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the...
480 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized Chrysler Group LLC Customer Center dealer’s service manager first. Most matters can be re- P.O. Box 21–8004 solved with this process. Auburn Hills, MI 48321–8004 Phone: (800) 992-1997 •...
IF YOU NEED CONSUMER ASSISTANCE 481 Customer Assistance For The Hearing Or Speech the manufacturer’s service contracts. If you purchased a Impaired (TDD/TTY) manufacturer’s service contract, you will receive Plan To assist customers who have hearing difficulties, the Provisions and an Owner Identification Card in the mail manufacturer has installed special TDD (Telecommuni- within three weeks of the vehicle delivery date.
See the Warranty Information Booklet, located on the has also made a major investment in facilities, tools, and DVD, for the terms and provisions of Chrysler Group training to assure that you are absolutely delighted with LLC warranties applicable to this vehicle.
IF YOU NEED CONSUMER ASSISTANCE 483 If NHTSA receives similar complaints, it may open an In Canada investigation, and if it finds that a safety defect exists in If you believe that your vehicle has a safety defect, you a group of vehicles, it may order a recall and remedy should contact the Customer Service Department imme- campaign.
Page 484
Chrysler Group LLC ve- taining, servicing, and repairing Chrysler Group LLC hicles. Included are starting, operating, emergency vehicles.
Page 485
IF YOU NEED CONSUMER ASSISTANCE 485 DEPARTMENT OF TRANSPORTATION UNIFORM significantly from the norm due to variations in driving TIRE QUALITY GRADES habits, service practices, and differences in road charac- The following tire grading categories were established by teristics and climate. the National Highway Traffic Safety Administration.
Page 486
486 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades WARNING! The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat The temperature grade for this tire is established for and its ability to dissipate heat, when tested under a tire that is properly inflated and not overloaded.