Extron electronics IN1804 Series User Manual page 85
Scaling presentation switchers scalers
Hide thumbs
Also See for IN1804 Series:
- Setup manual (4 pages) ,
- User manual (113 pages) ,
- Setup manual (4 pages)
Table of Contents
Advertisement
Command
Information Requests (continued)
Query part number
View internal temperature
Set verbose mode
View verbose mode
KEY:
X1@
= Internal temperature
X3$
= Verbose mode (see the
command description
more information)
X3^
= Part number
IP Control Port Commands
IP Setup
NOTES:
•
Changes made to any TCP/IP settings do not take effect until the reboot network command (
•
The following IP address setup commands that are followed by
issue them without Administrator status result in an E24 (privilege violation) error message.
Set DHCP mode
24
View DHCP mode
Set IP address
24
Read IP address
Set subnet mask
24
View subnet mask
Set gateway IP address
24
View gateway IP address
View MAC address
KEY:
X1)
=
On or off, enable or disable
X8&
=
IP address
X8*
=
Gateway address
X8(
=
Subnet mask
X9)
=
Hardware (MAC) address
ASCII Command
Response
(Host to Scaler)
(Scaler to Host)
X3^]
N
Verbose modes 2 and 3:
X3^]
Pno
E
}
X1@]
20STAT
Verbose modes 2 and 3:
20Stat•
EX3$
}
X3$]
CV
Vrb
E
}
X3$]
CV
In degrees Celsius. Response is two digits, padded with a zero.
0 = None (default for LAN connection)
verbose mode
1 = Verbose mode (default for RS-232 and USB connection)
on page 53 for
2 = Tagged responses to queries
3 = Verbose mode and tagged responses
IN1804 (standard) — 60-1699-01
IN1804 DI — 60-1699-02
IN1804 DO — 60-1699-03
E X1)
}
DH
Idh
E
}
X1)]
DH
E X8&
}
CI
Ipi
E
}
X8&]
CI
E X8(
}
CS
Ips
E
}
X8(]
CS
E X8*
}
CG
Ipg
E
}
X8*]
CG
E
}
X9)]
CH
Verbose modes 2 and 3:
Iph
0 = DHCP disabled (default), 1 = DHCP enabled
Format nnn.nnn.nnn.nnn (192.168.254.254 = default)
Leading zeros in each of the four octets are optional in setting values,
and are suppressed in returned values.
nnn.nnn.nnn.nnn (0.0.0.0 = default)
nnn.nnn.nnn.nnn (255.255.255.0 = default)
00-05-A6-xx-xx-xx
IN1804 Scaling Presentation Switcher • SIS Configuration and Control
Additional Description
View unit part number
View unit internal temperature
degrees Celsius.
X1@ ]
Set the verbose mode to
without tagged responses.
View the current verbose mode.
require Administrator permission to enter. Attempts to
24
X1)]
Enable or disable DHCP.
View the DHCP mode setting.
• X8&]
Set the IP address to
View the current IP address.
• X8(]
Set the subnet mask to
View the subnet mask setting.
• X8*]
Set the gateway IP address to
View the gateway IP address setting.
View unit Media Access Code (MAC)
address
• X9)]
X3^
for the model.
X1@
in
X3$
, with or
E
}
2BOOT
) is issued.
X8&
.
X8(
.
X8*
.
X9)
.
77
Advertisement
Table of Contents
