Related Manuals for Extron electronics IN1403
Summary of Contents for Extron electronics IN1403
- Page 1 Vertrieb von CAMBOARD Electronics IN1403 Video Scaler 68-1020-01 Rev. A 12 04 www.camboard.de Tel. 07131 911201 ce-info@camboard.de Fax 07131 911203...
- Page 2 im Vertrieb von CAMBOARD Electronics Precautions Safety Instructions • English Warning This symbol is intended to alert the user of important operating and maintenance Power sources • This equipment should be operated only from the power source indicated on the product.
-
Page 3: Table Of Contents
Description........................2 Features........................... 2 Compatibility ........................3 Input..........................3 Output..........................3 Installation .......................... 4 IN1403 application diagram ..................5 Operation ..........................5 Front panel controls....................... 5 On-screen menu ......................6 On-screen menu display system ..................7 Menu Commands ......................8 Video menu ........................ -
Page 4: Product Overview
CRT, LCD, DMD, ILA, D-ILA, and plasma display devices. Selectable Refresh Rate — The IN1403 output vertical refresh rate is adjustable from 60 Hz to 120 Hz By converting PAL (25 Hz) and NTSC (30 Hz) input signals to higher, more ergonomic refresh rates, the IN1403 makes it possible to display a remarkably solid, flicker-free image when using CRT monitors and projectors. -
Page 5: Compatibility
Dual Outputs — The IN1403 features a 5-BNC output and a 15-pin HD output. Since both are active simultaneously, the IN1403 can directly drive two separate display devices. -
Page 6: Installation
IN1403, and that the power button is off. Place or install the IN1403 at the desired location. Make sure that the unit is seated on a flat surface or is securely installed in a standard 19” equipment rack. The IN1403 is exactly 1U high without the feet. -
Page 7: In1403 Application Diagram
Input Select: The large buttons in the Input Select section, labeled INPUT 1, INPUT 2, INPUT 3 and INPUT 4 are used to select the desired input. After turning on the IN1403, press and release the desired Input Select button. A green LED will light underneath the button to indicate the selected input. -
Page 8: On-Screen Menu
The IN1403 saves the volume levels for each input automatically. Audio Mute: Mutes the audio for the selected input. Press the button to engage (the green LED below the button will illuminate), and press again to disengage. -
Page 9: On-Screen Menu Display System
Vertrieb von CAMBOARD Electronics IN1403 on-screen display menu system Main Menu Video Audio Input Output Advanced Video Audio Input Output Advanced Brightness Bass Signal Format Resolution Factory Reset Contrast Treble Aspect Ratio Refresh Rate Baud Rate Color Balance Hz Tracking... -
Page 10: Menu Commands
Color adjusts the color saturation of the picture over a wide range. Setting this control to 0 removes most of the color. Range: 0 to 255 Factory default setting: 140 Operation: Press button to increase the color. Press button to decrease the color. IN1403 User’s Manual www.camboard.de Tel. 07131 911201 ce-info@camboard.de Fax 07131 911203... - Page 11 We also recommend that, unless you’re a qualified audiovisual technician, you avoid the Advanced menu. Gamma: The 30 active gamma correction curves programmed into the IN1403 are used to compensate for the non-linear response of many display devices. Since Gamma, Brightness and Contrast controls interact with each other, the following order of adjustments is suggested: Set the brightness and contrast controls to factory default positions.
-
Page 12: Audio Menu
Neither filter has any effect on S-video signals. Reset Video resets all video settings to factory default (for current input only). Audio menu The IN1403 allows you to manually adjust the bass, treble, and balance settings. To do so Press the desired Input Select button. Press MENU. -
Page 13: Input Menu
Select the format for each individual input (use the buttons to toggle between composite and S-video). The IN1403 will save the format setting automatically. Press MENU to exit. It is critical that the composite/S-video status is selected properly for each input. Using the on-screen menu, you can set/change the input format at any time, even when another input signal is active. - Page 14 Vertrieb von CAMBOARD Electronics Example 1: Example 2 IN1403 User’s Manual www.camboard.de Tel. 07131 911201 ce-info@camboard.de Fax 07131 911203...
- Page 15 For good quality video signals, such as from a DVD player Slow: For high quality video signals, such as broadcast video Reset Input: Resets all input settings to factory default (for the current input only). IN1403 User’s Manual www.camboard.de Tel. 07131 911201 ce-info@camboard.de...
-
Page 16: Output Menu
This setting is useful to manually reduce the height of the output signal when an anamorphic input signal is connected. The IN1403 only scales up; therefore the output size controls will stop at a certain point where the input and output resolution are equal. -
Page 17: Choosing The Optimal Resolution And Refresh Rate
Choosing the Optimal Output Resolution and Refresh Rate Of all the settings on the IN1403, perhaps the most critical adjustment is the output resolution and output refresh rate. Every display device has an optimal or native resolution and an optimal refresh rate. -
Page 18: Crt Displays: Selecting The Optimal Refresh Rate
60 Hz with most LCD, DMD, LCOS, and plasma displays. Higher refresh rates are not recommended with these display technologies because they usually do not improve the image and may actually cause compatibility problems. IN1403 User’s Manual www.camboard.de Tel. 07131 911201 ce-info@camboard.de... - Page 19 NEC 50": Set Sync JVC / Luce / Marantz / NEC / Panasonic / 1365 x 768 60 Hz Format to RGBHV++ RCA / Runco / Samsung / Toshiba) IN1403 User’s Manual www.camboard.de Tel. 07131 911201 ce-info@camboard.de Fax 07131 911203...
-
Page 20: Advanced Operation
Input 4, even though the menu cannot be displayed. Output RGB connectors The dual RGB outputs of the IN1403 are individually buffered (including signals from Input 4). They may both be connected simultaneously without degradation of the other output. -
Page 21: Power-On Settings
Power-on settings let you adjust key IN1403 settings without using on-screen menus. This may be particularly helpful if the IN1403 has been accidentally set for a mode that is incompatible with the display device, preventing the viewing of the on-screen menus. To execute a Power-On setting, simply press and hold the desired front panel button (indicated in the chart below) while turning on the IN1403 power switch. - Page 22 The IN1403 can be set to recognize six sets of leading and end codes (delimiters). These are: ( ), [ ], { }, \ /, < >, and !#. The factory default serial delimiters are [ ]. The unit may be set to a different delimiter pair from the Advanced Menu (see page 14).
-
Page 23: In1403 Serial Commands
Vertrieb von CAMBOARD Electronics IN1403 serial commands* Command Description Command Description ACI3 set baud rate to 1200 CMDCD2 set delimiters to parentheses ( ) ACI4 set baud rate to 2400 CMDCD3 set delimiters to less and greater < >... - Page 24 REF0 set refresh rate to 60 Hz** decrease vertical size REF1 set refresh rate to 72 Hz set vertical size to normal**(100) IN1403 User’s Manual www.camboard.de Tel. 07131 911201 ce-info@camboard.de Fax 07131 911203...
- Page 25 * The commands are not case sensitive. ** Default values when factory reset is performed ♦ Normal and available values depend on the current output mode. IN1403 User’s Manual www.camboard.de Tel. 07131 911201 ce-info@camboard.de Fax 07131 911203...
-
Page 26: Troubleshooting
• Solution 2: Make sure the A/C source is live. • Solution 3: Verify that the power switch is turned on for the video source, the IN1403, and the monitor. • Solution 4: Verify the connection to the output display device. Even with no input signal, the IN1403 menu can be displayed. - Page 27 Solution 3: Change the comb or trap filter setting (applicable only in composite video mode). Problem: The Output Resolution will not decrease. • Solution: The IN1403 can only scale up. Resolutions that would result in scaling down are not available. IN1403 User’s Manual www.camboard.de Tel.
-
Page 28: Specifications
CAMBOARD Electronics Problem: The desired Input Aspect Ratio cannot be selected. • Solution 1: The IN1403 can only scale up. Increase the output resolution until the desired aspect ratio is available. • Solution 2: Manually decrease the image size by using the output menu. -
Page 29: Part Numbers
MTBF ..........30,000 hours Warranty ........3 years parts and labor All nominal levels are at ±10%. Specifications are subject to change without notice. Part Numbers These items are included with the IN1403. Included Parts Part Numbers IN1403-2 scaler 60-730-01... - Page 30 Vertrieb von CAMBOARD Electronics IN1403 User’s Manual www.camboard.de Tel. 07131 911201 ce-info@camboard.de Fax 07131 911203...
- Page 31 CAMBOARD Electronics Extron’s Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of two years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will, at its option,...
- Page 32 PM Industrial Building 16 Ichibancho The Netherlands Singapore 368363 Chiyoda-ku, Tokyo 102-0082 Japan 714.491.1500 +31.33.453.4040 +65.6383.4400 +81.3.3511.7655 www.extron.com Fax 714.491.1517 Fax +31.33.453.4050 Fax +65.6383.4664 Fax +81.3.3511.7656 www.camboard.de Tel. 07131 911201 ce-info@camboard.de © 2005 Extron Electronics. All rights reserved. Fax 07131 911203...