JCM GLOBAL VEGA Series Operation And Maintenance Manual page 102

Section A
On-line Off-line
Color Color
Flashes Flashes
(Interval (Interval
[msec]) [msec])
Red Blue
3 2
Transportation Slips
(300) (300)
Red Blue
Transportation Times
3 3
(300) (300)
Red Red
3 3
(Transport, Reject,
(300) (300)
Red Red
Cash Box Seating
3 5
(300) (300)
Red Purple
Pusher Mechanism
3 3
(300) (300)
Red Orange
3 3
(300) (300)
Red Cyan
3 3
(100) (100)
*. The Flash error pause time between blinks is a 100msec duration.
P/N 960-100189R_Rev. 4 {EDP #148850}
VEGA™ Series Banknote Validator
Table A-2 Error Codes
Error
An abnormal Banknote transportation error is detected when
transporting or rejecting Banknotes. The Transportation Slip Sensors do
not detect continuous Banknotes being transported according to the
rated value.
Banknote
[Solution] Check that the following parts are properly assembled and/or
Harness connected, and clean all of the Sensors.
[Relative Parts] Feed Motor, Stack-in Sensor, Cash Box Sensor, Storage
Flap Sensor, Escrow Sensor, Validation Sensor 
If the error is not resolved, change the above related part or parts.
An abnormal Banknote transportation error is detected when
transporting or rejecting Banknotes. The Transportation Locks-up or
runs too slow. Sensors detect continuous Banknotes being transported
according to the rated value.
[Solution] Check that the following parts are properly assembled and/or
Out
Harness connected, and clean all of the Sensors.
[Relative Parts] Feed Motor, Stack-in Sensor, Storage Flap Sensor,
Escrow Sensor, Validation Sensor 
If the error is not resolved, change the above related part or parts.
Sensors detect Banknotes remain in path or none exist during abnormal
timing.
Abnormal Timing [Solution] Check that the following parts are properly assembled and/or
Response Harness connected, and clean all of Sensors.
[Relative Parts] Stack-in Sensor, Box Sensor, Store Flap Sensor, Escrow
other)
Sensor, RC Flap Sensor, Side Sensor, Pusher Mechanism Home
Position Sensor, Validation Sensor 
If the error is not resolved, change the above relative part or parts.
Cash Box Sensors detect a Banknotes remaining in path or a Cash Box
not properly seated.
[Solution] Check that the following parts are properly assembled and/or
Problem Harness connected, and clean all of the Sensors.
[Relative Parts] Cash Box Sensor 
If the error is not resolved, change the above related part.
Pusher Mechanism Home Sensor detects that the Pusher Mechanism is
not presently seated at the Home end position.
[Solution] Check that the following parts are properly assembled and/or
Position Problem Harness connected, and clean all of the Sensors.
[Relative Parts] Pusher Mechanism Home Position Sensor 
If the error is not resolved, change the above related part.
When the Pusher Mechanism movement proceeds toward stacking, the
Stacker-full Sensor determined that the time taken is longer than
specified value for the function.
[Solution] Check that the following parts are properly assembled and/or
Stacker Full
Harness connected. and clean all of the Sensors.
[Relative Parts] Pusher Mechanism Assembly and inspect movement
path 
If the error is not resolved, change the above related part.
Intake Sensor detects Banknote at a position where it can be returned
while in the transportation process.
[Solutions] Check that the following parts are properly assembled and/or
*
Pause
Harness connected, and clean all of the Sensors.
[Relative Parts] Intake Sensor 
If error is not resolved, change the above relative part.
Causes and Solutions
© 2016, JAPAN CASH MACHINE CO., LTD.
A - 4
Troubleshooting