JCM GLOBAL TBV-100 FSH Quick Reference Manual
  1. Manuals
  2. Brands
  3. JCM GLOBAL Manuals
  4. Bank Note Validator
  5. TBV-100 FSH
  6. Quick reference manual

JCM GLOBAL TBV-100 FSH Quick Reference Manual

Hide thumbs Also See for TBV-100 FSH:
Table of Contents

Advertisement

Quick Links

TBV
NOTE: Due to advancements in industry
technologies and future product development,
the information in this guide is subject to
change without notice.
For more information about product set-up, use, testing procedures
and troubleshooting methods, please contact the Technical Support
Division of Customer Service via the email addresses listed below:
Europe, Middle East, Africa & Russia
JCM Products
Quick Reference Guide
-100/101 Units
™
Americas
support@jcmglobal.com
support@jcmglobal.eu
Asia & Oceania
asiasupport@jcmglobal.com
© 2019 JCM Global Corporation
Part No. 960-000207R_Rev. A

Advertisement

Table of Contents
loading

Related Manuals for JCM GLOBAL TBV-100 FSH

Summary of Contents for JCM GLOBAL TBV-100 FSH

  • Page 1 Technical Support Division of Customer Service via the email addresses listed below: Americas support@jcmglobal.com Europe, Middle East, Africa & Russia support@jcmglobal.eu Asia & Oceania asiasupport@jcmglobal.com © 2019 JCM Global Corporation Part No. 960-000207R_Rev. A...
  • Page 2 LEDs are OFF.) malfunctioning. connectors. Replace the CPU Board. The TBV is not communicating with Check the interface settings and the the Host machine. DIP Switch Settings. Interface DIP Switch Settings incorrect. © 2019 JCM Global Corporation Part No. 960-000207R_Rev. A...
  • Page 3 Improper assembly Identify the LED Error Code flashing and/or Harness pattern and identify the error. connection. CPU Refer to the Error Code Tables. Board and/or Sensor are malfunctioning. © 2019 JCM Global Corporation Part No. 960-000207R_Rev. A...

  • Page 4: Dip Switch Settings

    NOTE: The following DIP Switches are not shown in Figure 1: DS3 - On front of Transport DS7 - On Cash Box NOTE: DIP Switch DS6 Memory Selection Switch is not used. © 2019 JCM Global Corporation Part No. 960-000207R_Rev. A...
  • Page 5 Table 4 DS2 - BNF Buzzer/Volume Switch Switch Switch ON Switch OFF OFF (Fixed) Performance Buzzer ON Performance Buzzer OFF ON (Fixed) OFF (Fixed) * N/A = Not Applicable (never switched to ON position). © 2019 JCM Global Corporation Part No. 960-000207R_Rev. A...
  • Page 6 Photo-Coupler protocol. cc-Talk Table 6 DS5 - Communications Interface Setting Photo-Coupler RS-232 Switch Switch ON Switch OFF Photo-Coupler RS-232 * Match each setting to DIP Switch DS4 Switches 3 and 4. © 2019 JCM Global Corporation Part No. 960-000207R_Rev. A...
  • Page 7 † Returns to Standby Mode from a RESET Command or after clearing the error condition (See Standard LED Flash Codes, Operational Errors and Reject Codes later in this Guide to resolve the detected error type). © 2019 JCM Global Corporation Part No. 960-000207R_Rev. A...

  • Page 8: Operational Mode

    Figure 2 JCM Tool Suite Service Mode Drop-down Menu NOTE: Refer to Table 8 JCM Tool Suite Application Functions on page 9 for descriptions of Sensor Adjustment and Performance Test Options. © 2019 JCM Global Corporation Part No. 960-000207R_Rev. A...
  • Page 9 Display Historical Activity on the TBV Event Log View Unit. Sensor Adjustment Used to calibrate TBV Unit Sensors Test Mode Used to test the TBV Unit’s Motor, Performance Test Solenoid and Sensor functions. © 2019 JCM Global Corporation Part No. 960-000207R_Rev. A...

  • Page 10: Downloading Firmware

    1, 6, 7 and 8 are ON, and Forced Download is indicated by a Flashing GREEN LED Status Indicator. 6. Verify that the download indicates Download Success. Download is now complete. Figure 3 JCM Downloader Suite Edition Version x.x.x Screen © 2019 JCM Global Corporation Part No. 960-000207R_Rev. A...
  • Page 11 ) to start the Load Firmware Download. 6. When the BlueWave 2.0 Unit’s Top and Middle LEDs ) turn GREEN, the Download is complete. (Figure 4 Figure 4 BlueWave 2.0 (DT-200) Unit © 2019 JCM Global Corporation Part No. 960-000207R_Rev. A...
  • Page 12 7. When the Download is complete, press the CLR button to return to the menu (Figure 5 8. Disconnect the USB Cable from the Unit (Figure 5 Figure 5 BlueWaveDX (DT-300) Unit © 2019 JCM Global Corporation Part No. 960-000207R_Rev. A...

  • Page 13: Performance Testing

    STOP NOTE: When an Operation Test is selected, click the Close box “X” icon (Figure 6 d) to halt the Test and close the screen. Figure 6 TBV Performance Test Options © 2019 JCM Global Corporation Part No. 960-000207R_Rev. A...
  • Page 14 5) Click the Sensor ON/OFF tab, then click the Start button. The Judgement Sensor Status will display as ON. Figure 7 Opening TBV Transport Guide Rear 85 Section Figure 1-1 Open © 2019 JCM Global Corporation Part No. 960-000207R_Rev. A...
  • Page 15 ), then click the button (Figure 8 Start 3. Follow the onscreen prompts to insert or remove Calibration Reference Paper, as indicated. Figure 8 TBV Calibration Tool [Maintenance] Screen Figure 1-1 © 2019 JCM Global Corporation Part No. 960-000207R_Rev. A...
  • Page 16 Sensors detect a Banknote with Remaining Banknote abnormal timing. Cash Box Lock Released Sensors detect the Cash Box has been unlocked. Sensors detect that the Transport Transport Cover Open Cover is open. © 2019 JCM Global Corporation Part No. 960-000207R_Rev. A...

  • Page 17: Operational Errors

    Feed Motor Speed Motor encoder pulses out of range. Detected communications data transfer BNF Communications rate improper. ICB Communications ICB Communications abnormal. Voltage Input voltage is too low. © 2019 JCM Global Corporation Part No. 960-000207R_Rev. A...
  • Page 18 Table 11 Return/Reject Error Codes GREEN Error Type Cause and Solution Flashes Detected Banknote inserted in an Skewed Insertion incorrect direction. Abnormal Magnetic Magnetic Sensor detects abnormal detected levels. © 2019 JCM Global Corporation Part No. 960-000207R_Rev. A...
  • Page 19 Banknote Length than specified, Banknote pattern is greater than rated Margin Pattern 1 value Banknote validation indicated an invalid Banknote Identity Banknote, Banknote Pattern is greater than rated Margin Pattern 2 value. © 2019 JCM Global Corporation Part No. 960-000207R_Rev. A...
  • Page 20 * Refer to Table A-6 and A-7 in the TBV™ Series Transaction Based Validator Operation and Maintenance Man- ual (JCM Part No. 960-100926R) for Sensor Flag Values indicated in the “YYYY-YYYY-YYYY-YYYY” or “zz-zz- zz” formats. © 2019 JCM Global Corporation Part No. 960-000207R_Rev. A...
  • Page 21 00-08-00 BOX_LOK Box Lock Sensor 00-10-00 GS_HOME Shutter Unit Home Positioning Sensor 00-20-00 BNF_INS BNF Entrance Sensor 01-00-00 BNF_MID BNF Assignation Sensor 02-00-00 BNF_REJ BNF Reject Sensor 04-00-00 Bar Sensor 10-00-00 © 2019 JCM Global Corporation Part No. 960-000207R_Rev. A...
  • Page 22 0000-0000-0000-0200 dc_redr_ref 0000-0000-0000-0400 drr_gre_ref 0000-0000-0000-0800 ull_ore_ref 0000-0000-0000-1000 ul_blu_ref 0000-0000-0000-2000 uc_redl_ref 0000-0000-0000-4000 ur_blu_ref 0000-0000-0000-8000 urr_ore_ref 0000-0000-0001-0000 uc_irl_ref 0000-0000-0002-0000 uc_irr_ref 0000-0000-0004-0000 ull_gre_ref 0000-0000-0008-0000 ul_ir_ref 0000-0000-0010-0000 uc_redr_ref 0000-0000-0020-0000 ur_ir_ref 0000-0000-0040-0000 urr_gre_ref 0000-0000-0080-0000 dc_redl_pen 0000-0000-0100-0000 © 2019 JCM Global Corporation Part No. 960-000207R_Rev. A...
  • Page 23 0000-0010-0000-0000 do_redr_pen 0000-0020-0000-0000 dr_ore_pen 0000-0040-0000-0000 drr_gre_pen 0000-0080-0000-0000 ull_ore_pen 0000-0100-0000-0000 ul_blu_pen 0000-0200-0000-0000 ur_blu_pen 0000-0400-0000-0000 urr_ore_pen 0000-0800-0000-0000 ull_nir_pen 0000-1000-0000-0000 ul_ore_pen 0000-2000-0000-0000 ur_ore_pen 0000-4000-0000-0000 urr_nir_pen 0000-8000-0000-0000 ull_ir_pen 0001-0000-0000-0000 ul_ir_pen 0002-0000-0000-0000 ur_ir_pen 0004-0000-0000-0000 urr_ir_pen 0008-0000-0000-0000 © 2019 JCM Global Corporation Part No. 960-000207R_Rev. A...

  • Page 24: Preventive Maintenance

    NOTE: The Stacking Assembly may need to be removed from the Cash Box and disassembled for proper cleaning. 2. Check the Belts and all moving parts for wear and proper positioning. © 2019 JCM Global Corporation Part No. 960-000207R_Rev. A...
  • Page 25 JCM Europe (UK Office) Unit B, Third Avenue Denbigh West Business Park Bletchley, Milton Keynes Buckinghamshire MK1 1DH UK Phone: +44 (0) 190-837-7331 Fax: +44 (0) 190-837-7834 Email: support@jcmglobal.eu TBV™-100/101 Units Quick Reference Guide © 2019 JCM Global Corporation Part No. 960-000207R_Rev. A...
  • Page 26 N.T. Hong Kong Phone: +852-2429-7187 Fax: +852-2929-7003 Email: asiasupport@jcmglobal.com JAPAN CASH MACHINE CO., LTD. (HQ) 2-3-15, Nishiwaki, Hirano-ku Osaka 547-0035 JAPAN Office: +81-6-6703-8400 Fax: +81-6-6707-0348 Email: Shohin@jcm-hq.co.jp TBV™-100/101 Units Quick Reference Guide © 2019 JCM Global Corporation Part No. 960-000207R_Rev. A...

This manual is also suitable for:

Tbv-101 fshTbv-100 fldTbv-101 fldTbv-100 gldTbv-101 gshTbv-101 ash

Table of Contents