Mitsubishi M80 series Connection And Set Up Manual page 34

17.1.2 Setting DIP Switch ................................................................................................................... 319
17.2 Setting Drive Unit MDS-EM/EMH Series ......................................................................................... 320
17.2.1 Setting the Rotary Switch......................................................................................................... 320
17.3 Setting Drive Unit MDS-EJ/EJH Series............................................................................................ 321
17.3.1 Setting the Rotary Switch......................................................................................................... 321
17.3.2 Setting the DIP Switch ............................................................................................................. 322
17.4 Setting Up without Connecting to the Motor/Drive Units at the Startup of Drive Unit ...................... 323
17.5 Connecting the Batteries.................................................................................................................. 324
17.5.1 Control Unit Battery.................................................................................................................. 324
17.5.2 Servo Drive Unit Battery .......................................................................................................... 326
17.6 Connecting and Setting the Remote I/O Unit................................................................................... 329
17.6.1 Outline of the Remote I/O Unit................................................................................................. 329
17.6.2 Connection and Station No. Setting on Remote I/O Unit ......................................................... 331
17.6.3 Station No. Setting when Using Multiple Remote I/O Units ..................................................... 334
17.6.4 PLC Device Assignment of Digital Signal (DI/DO)................................................................... 337
17.6.4.1 Fixed Device Assignment ................................................................................................ 338
17.6.4.2 Arbitrary Device Assignment ........................................................................................... 339
17.6.5 Thermistor Input Interface........................................................................................................ 343
17.7 Initializing the NC Internal Data (SRAM).......................................................................................... 344
18 Setting Up with M80/M800S SETUP INSTALLER ................................................................................ 347
18.1 Activate M80/M800S SETUP INSTALLER ...................................................................................... 349
18.2 Install Custom Screen...................................................................................................................... 351
18.3 Install Start-up Screen ..................................................................................................................... 352
18.4 Install APLC C Language Module.................................................................................................... 353
18.5 Install User Cycle ............................................................................................................................. 354
19 Setting the Parameters and Date/Time ................................................................................................ 355
19.1 Selecting the NC System Type and Displayed Language ............................................................... 356
19.2 Setting the Parameters for the System Specifications..................................................................... 357
19.3 Setting the Parameters for the Machine Specifications ................................................................... 358
19.4 Setting Date and Time ..................................................................................................................... 360
20 PLC Program Writing............................................................................................................................. 361
20.1 Writing PLC Program using the SD Card......................................................................................... 362
20.2 Setting the Ethernet Communication ............................................................................................... 362
20.2.1 Confirming the IP Address for CNC ......................................................................................... 362
20.2.2 Setting the IP Address for PC Side.......................................................................................... 362
20.3 Connecting the Control Unit and a Personal Computer................................................................... 364
20.4 Setting the Communication with GX Developer............................................................................... 365
20.5 Setting the Parameters on GX Developer........................................................................................ 366
20.5.1 Parameter Setting Screen........................................................................................................ 366
20.5.2 Setting the Number of Device Points ....................................................................................... 367
20.5.3 Setting the Number of Common Pointer Points ....................................................................... 368
20.5.4 Setting the Program Execution Order ...................................................................................... 369
20.6 Writing a PLC Program with GX Developer ..................................................................................... 370
20.7 Writing a PLC Program to ROM with GX Developer........................................................................ 371
20.8 Setting the PLC Parameters ............................................................................................................ 372
21 Confirming the Basic Operation ........................................................................................................... 373
21.1 Checking Inputs/Outputs and Alarms .............................................................................................. 374
21.2 Confirming Manual Operation .......................................................................................................... 375
21.2.1 Using the Manual Pulse Generator.......................................................................................... 375
21.2.2 Using JOG Feed ...................................................................................................................... 375
21.3 Servo Simplified Adjustment ............................................................................................................ 376
21.3.1 First Measure Against Vibration............................................................................................... 376
21.3.2 NC Analyzer2........................................................................................................................... 377
22 Setting the Position Detection System ................................................................................................ 379
22.1 Adjusting the Absolute Position Detection System .......................................................................... 380