Related Manuals for Mitsubishi MAC-588IF-E
Summary of Contents for Mitsubishi MAC-588IF-E
- Page 1 Wi-Fi INTERFACE MODEL MAC-568IF-E MAC-588IF-E INSTALLATION GUIDE Intelligent control, no matter where you are.
- Page 2 • Router capable of WPA2-PSK(AES) encryption. 2.4GHz needs to be enabled on dual band Routers. The wireless network coverage must include the heat pump installation location. • A PC or Smartphone/Tablet that is iOS/Android compatible. • A compatible Mitsubishi Electric indoor unit with a Wi-Fi interface.
- Page 3 Wi-Fi interface or generation, or fire. professional installer. • Mitsubishi Electric’s components or other • The Wi-Fi interface should be securely designated components must be used for installed in accordance with this installation.
- Page 4 Warning (Improper handling may have serious consequences, including serious injury or death.) • Attach the electrical cover to the indoor • Do not install the Wi-Fi interface nearby unit securely. the automatic control devices such as If the electrical cover of the indoor units is not automatic doors or fire alarms.
- Page 5 [Precautions for setting up, or use of the Wi-Fi interface] Warning (Improper handling may have serious consequences, including serious injury or death.) Be sure not to do. Never touch with wet hand. • Do not disassemble, modify, or repair by •...
- Page 6 Wi-Fi service. Third party Wi-Fi interfaces cannot connect to Mitsubishi Electric’s Wi-Fi service. Mitsubishi Electric is not responsible for any (i) underperformance of a system or any product; (ii) system or product fault; or (iii) loss or damage to any system or product;...
- Page 7 : XXXXXXXXXX SSID : XXXXXXXXXXXX : XXXXXXXXXXXX 2 RESET Button Resets the system and ALL settings. VOLTAGE CURRENT MODE MITSUBISHI ELECTRIC CORPORATION UNIT MODE UNIT 3 ERR LED (Orange) Shows the network error state. RESET MODE RESET MODE WiFi.ASSY DWG No.
- Page 8 WPS-PIN mode <MAC-568IF-E only> [To enter the mode] Hold down the MODE Button for 14 seconds. [LED indication] When WPS-PIN is enabled on the Wi-Fi interface, the MODE LED starts flashing orange (every 0.5 seconds). [To cancel the mode] Hold down the RESET Button for 2 seconds to return to the initial state. (2) RESET Button •...
- Page 9 Parts Interface unit Fixing screw Fixing screw Mounting cord Fastener Holder Clip (with connecting clamp (for bundling cable) 3.5×16 mm 4×16 mm the wires) Connecting the Wi-Fi Interface (For details about your heat pump, see the relevant installation manual) Before dismantling the indoor unit, turn the power off and make sure that the power has been disconnected from the complete system.
- Page 10 Holder Holder Mark for cable Align Interface unit Connecting cable Clip Insert the interface unit into the holder until Insert the clip into the holder until it clicks it clicks into place. into place. Note: When inserting the interface unit into the holder, align the cable of the interface unit with the mark for the cable on the holder...
- Page 11 UNIT LED should be flashing green RESET MODE only. Download and install Wi-Fi Control App to your compatible Apple or Android smartphone/tablet (search term: Mitsubishi Wi-Fi Control). THERE ARE TWO OPTIONS OF CONNECTING Option 1 - Access Point Mode Pairing MODE UNIT...
- Page 12 For MAC-588IF-E, Scan the matrix Open Wi-Fi Control App and follow barcode from the label on the back the ‘How to Setup’ instructions in the ‘Setup Wi-Fi interface’ section. of the interface to connect to its network. If you can't connect this Wi-Fi...
- Page 13 Option 2 - WPS-Push Pairing • Please Note: The WPS and Router reset buttons may be similar on some Routers. • Please exercise caution as resetting your Router will erase network configuration. Check Wi-Fi and WPS are enabled Activate WPS Mode on your Router. on your Router.
- Page 14 Open Wi-Fi Control App. Enter MAC Once completed, control your heat and ID into ‘Add new unit’ and select pump via Wi-Fi. ‘Add’.
- Page 15 LED Pattern Flashing ● Software initialising MODE UNIT Description (Orange) (Green) (Orange) (Green) Firmware updating Firmware downloading (every second) (every second) Reset to the factory default ● Wireless setting MODE UNIT Description (Orange) (Green) (Orange) (Green) Access Point Mode acti- vated (every 5 sec) (every 5 sec)
- Page 16 Troubleshooting : ON : OFF : Flashing MODE UNIT Description (Orange) (Green) (Orange) (Green) Connection to server established, and connection to indoor unit failed Connection to Router failed, and connection to indoor unit established Connection to Router failed, and starting up indoor unit connection Connection to Router failed, and connection to indoor unit failed...
- Page 17 (*2) Details of flash pattern • Every 0.5 sec: IP address setting is invalid. Make sure that DHCP is enabled, or check IP address settings of the Wi-Fi interface. If there are no problems on the items above, but the lamp is still flashing, push RESET Button for more than 14 seconds to retry the pairing.
- Page 18 End user registers and accepts the terms and conditions of the Wi-Fi service. • This Wi-Fi interface should not be installed and connected to any Mitsubishi Electric system which is to provide application critical cooling or heating.
- Page 19 Mitsubishi Electric Wi-Fi Heat Pump Control Register Your Heat Pump(s) Thank you for choosing a Mitsubishi Electric Heat Pump with Wi-Fi Control. Once your Wi-Fi interface is installed, either download the app (search term: Mitsubishi Wi-Fi Control) or visit our website to register your heat pump(s).
- Page 20 Helpline opening hours 8.30am - 5.00pm weekdays HEAD OFFICE: TOKYO BUILDING, 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN MITSUBISHI ELECTRIC CONSUMER PRODUCTS (THAILAND) CO., LTD AMATA NAKORN INDUSTRIAL ESTATE 700/406 MOO 7, TAMBON DON HUA ROH, AMPHUR MUANG, CHONBURI 20000, THAILAND...