Mitsubishi M80 series Connection And Set Up Manual page 32

7.6 Connecting with Drive Unit................................................................................................................. 190
7.6.1 Connecting with Drive Unit MDS-E/EH Series........................................................................... 191
7.6.2 Connecting with Drive Unit MDS-EM/EMH Series..................................................................... 193
7.6.3 Connecting with Drive Unit MDS-EJ/EJH Series ....................................................................... 195
7.7 Connecting with RS-232C Device...................................................................................................... 196
7.8 Connecting with Skip Signal (Sensor)................................................................................................ 197
7.9 Connecting with Manual Pulse Generator ......................................................................................... 199
7.9.1 Handle Numbers ........................................................................................................................ 200
7.10 Connecting with Synchronous Feed Encoder.................................................................................. 201
7.11 Connecting I/O Device via Communication Expansion Unit ............................................................ 202
7.11.1 Connecting I/O Device via CC-Link ......................................................................................... 203
7.11.2 Connecting I/O Device via PROFIBUS-DP.............................................................................. 206
7.11.3 Connecting I/O Device via EtherNet/IP.................................................................................... 207
8 Connection of Keyboard Unit ................................................................................................................. 209
8.1 Keyboard Unit Connection System Drawing...................................................................................... 210
8.2 Connecting with Operation Panel I/O Unit ......................................................................................... 210
9 Connection of Operation Panel I/O Unit................................................................................................. 211
9.1 Operation Panel I/O Unit Connection System Drawing ..................................................................... 212
9.2 Connecting with Frame Ground ......................................................................................................... 213
9.3 Connecting with Control Unit ............................................................................................................. 214
9.4 Connecting with Keyboard Unit.......................................................................................................... 214
9.5 Connecting with Remote I/O Unit....................................................................................................... 215
9.6 Connecting with Manual Pulse Generator (MPG).............................................................................. 216
9.6.1 Handle Numbers ........................................................................................................................ 218
9.7 Connecting with Machine Operation Panel........................................................................................ 219
9.7.1 Wiring for 24V Common Input.................................................................................................... 220
9.7.2 Wiring for 0V Common Input...................................................................................................... 221
9.7.3 Wiring for Source Type Output .................................................................................................. 222
9.7.4 Example of Wiring CJ42 (FCU8-DX760) ................................................................................... 223
9.8 Connecting with Analog I/O Signal (FCU8-DX761) ........................................................................... 224
10 Connection of Remote I/O Unit ............................................................................................................. 225
10.1 Remote I/O Unit Connection System Drawing................................................................................. 226
10.2 Connecting with Power Supply ........................................................................................................ 227
10.3 Connecting with Frame Ground ....................................................................................................... 229
10.4 Connecting with Control Unit ........................................................................................................... 230
10.5 Connecting with Operation Panel I/O Unit ....................................................................................... 231
10.6 Connecting with Machine Control Signal
(FCU8-DX220 / FCU8-DX230 / FCU8-DX231 / FCU8-DX651) ....................................................... 232
10.7 Connecting with Machine Control Signal
(FCU8-DX213 / FCU8-DX213-1 / FCU8-DX654 / FCU8-DX654-1) ................................................. 237
10.8 Connecting with Safety Machine Control Signal (FCU8-DX651) ..................................................... 245
10.9 Connecting with Analog I/O Signal (FCU8-DX202) ......................................................................... 247
10.10 Connecting with Thermistor (FCU8-DX408) .................................................................................. 249
11 Connection of Manual Pulse Generator............................................................................................... 253
11.1 Manual Pulse Generator Connection System Drawing.................................................................... 254
11.2 Connecting with Control Unit ........................................................................................................... 255
11.3 Connecting with Operation Panel I/O Unit ....................................................................................... 255
12 Connection of Synchronous Feed Encoder ........................................................................................ 257
12.1 Synchronous Feed Encoder Connection System Drawing .............................................................. 258
12.2 Connecting with Control Unit ........................................................................................................... 258
13 Connection of MITSUBISHI CNC Machine Operation Panel .............................................................. 259
13.1 Machine Operation Panel Connection System Drawing .................................................................. 260
13.2 Connecting with Power Supply ........................................................................................................ 261
13.3 Connecting with Frame Ground ....................................................................................................... 262