NEC UNIVERGE SV8100 System Hardware Manual

NEC UNIVERGE SV8100 System Hardware Manual

Hide thumbs Also See for UNIVERGE SV8100:
Table of Contents

Advertisement

System Hardware Manual
Issue 7.0 November 2012

Advertisement

Table of Contents
loading

Summary of Contents for NEC UNIVERGE SV8100

  • Page 1 System Hardware Manual Issue 7.0 November 2012...
  • Page 2 THIS PAGE INTENTIONALLY LEFT BLANK...
  • Page 3: Table Of Contents

    TABLE OF CONTENTS ___________________________________________________________________________________ Regulatory Chapter 1 Introduction to SV8100 Section 1 General Information ..............1-1 Section 2 Equipment List ................1-4 Chapter 2 SV8100 System Specifications Section 1 General Information ..............2-1 Section 2 System Block Diagram ..............2-1 Section 3 Maximum System Capacities ............
  • Page 4 Issue 7.0 UNIVERGE SV8100 ___________________________________________________________________________________ 5.5.1 Transmission ................2-22 5.5.2 Network ..................2-23 5.5.3 Control ..................2-23 5.5.4 Electra Elite IPK Terminals and Equipment ......2-24 5.5.5 Series i Terminals ..............2-25 Dialing Specifications ..............2-25 5.6.1 Dial Pulse Address Signaling ...........2-25 5.6.2 Dual-Tone Multifrequency (DTMF) Address Signaling .....2-25 5.6.3...
  • Page 5 UNIVERGE SV8100 Issue 7.0 ___________________________________________________________________________________ 2.2.1 CHS2U Chassis Installation ............. 3-12 2.2.2 Multiple CHS2U Chassis Installation ........3-14 Stand Mounting the 19” Chassis ..........3-16 2.3.1 CHS2U Chassis Installation ............. 3-16 2.3.2 Multiple CHS2U Chassis Installation ........3-19 Rack Mounting the 19” Chassis ..........3-22 Wall Mounting the 9.5”...
  • Page 6 Issue 7.0 UNIVERGE SV8100 ___________________________________________________________________________________ 2.8.2 Install Additional Blades 9.5” Chassis ........3-55 2.8.3 Apply Power to the 9.5” Chassis ..........3-55 Section 3 Battery Connection ..............3-56 Installing the Internal Batteries ..........3-56 Installing the External Batteries ..........3-62 3.2.1 Floor Mounting the CHS LARGE BATT BOX ......3-62 3.2.2...
  • Page 7 UNIVERGE SV8100 Issue 7.0 ___________________________________________________________________________________ 2.2.3 Order of Installing Trunk Blades ..........4-6 2.2.3.1 Installing CD-4COTA, CD-4DIOPB, CD-4ODTB or CD-2BRIA blades 4-6 2.2.3.2 Installing CD-PRTA (T1/PRI) Blades ........4-8 Remove an Extension or Trunk Blade ......... 4-8 Uninstalling a Blade Slot Through Software ........ 4-8 Blade Capacities ................
  • Page 8 Issue 7.0 UNIVERGE SV8100 ___________________________________________________________________________________ 3.3.1 Description ................4-30 3.3.2 Installation ................4-31 3.3.3 Switch Settings .................4-33 3.3.4 Remote PC Programming access ..........4-33 PZ-32IPLA/PZ-64IPLA/PZ-128IPLA (Voice over IP Daughter Boards) 4-33 3.4.1 Description ................4-35 3.4.2 Installation ................4-36 3.4.3 Switch Settings .................4-36 3.4.4 LED Indications ................4-37 3.4.5...
  • Page 9 UNIVERGE SV8100 Issue 7.0 ___________________________________________________________________________________ CD-4LCA/ CD-8LCA (4-Port/8-Port Single Line Interface) ..4-52 4.3.1 Description ................4-53 4.3.2 Installation ................4-55 4.3.3 LED Indications ................ 4-55 4.3.4 Connectors ................4-57 PZ-4LCA/PZ-8LCE (4-Port/8-Port SLI Daughter Boards) ..4-58 4.4.1 Description ................4-60 4.4.2...
  • Page 10 Issue 7.0 UNIVERGE SV8100 ___________________________________________________________________________________ 5.1.1 Description ................4-74 5.1.2 Installation ................4-76 5.1.3 LED Indications ................4-76 5.1.4 Connectors ................4-77 PZ-4COTE (4 Loop Start Interface Daughter Board) ....4-78 5.2.1 Description ................4-78 5.2.2 Installation ................4-80 5.2.3 Connectors ................4-80 CD-8COTAH (8 Port Analogue Trunk Card) ......4-81 5.3.1...
  • Page 11 UNIVERGE SV8100 Issue 7.0 ___________________________________________________________________________________ 5.6.2 Installation ................4-96 5.6.3 LED Indications ................ 4-96 5.6.4 Connectors ................4-97 CD-PRTA (PRI Interface) ............4-98 5.7.1 Description ................4-98 5.7.2 Installation ................4-99 5.7.3 LED Indications ..............4-101 5.7.4 Connectors ................4-103 CD-4ODTB (4-Port Tie Line Interface Blade) ......
  • Page 12 Issue 7.0 UNIVERGE SV8100 ___________________________________________________________________________________ 6.3.2 Installation ................4-118 6.3.2.1 Stacking Architecture ............4-118 6.3.2.2 CD-CP00IP Address Assignment ........4-119 6.3.2.3 Group Formation .............. 4-119 6.3.2.4 Port Number Determination ..........4-119 6.3.2.5 Unmanaged Switch Functions ......... 4-120 6.3.3 LED Indications ..............4-120 6.3.4...
  • Page 13 UNIVERGE SV8100 Issue 7.0 ___________________________________________________________________________________ 3.1.4 ITL-8LD-1 (BK) TEL/ITL-8LD-1 (WH) TEL ....... 5-18 3.1.5 ITL-12D-1 (BK) TEL/ITL-12D-1 (WH) TEL ....... 5-19 3.1.6 ITL-12CG-3 (BK) TEL .............. 5-20 3.1.7 ITL-12DG-3 (BK) TEL .............. 5-21 3.1.8 ITL-12PA-1 (BK) TEL ............... 5-22 3.1.9 ITL-24D-1 (BK) TEL/ITL-24D-1 (WH) TEL .......
  • Page 14 Issue 7.0 UNIVERGE SV8100 ___________________________________________________________________________________ 4.10 Wall Mounting the Multiline Terminal .........5-48 4.10.1 Wall Mounting a Multiline Terminal using the Base Plate ..5-48 4.10.1.1 Adjusting the Hanger Hook ..........5-48 4.10.1.2 Wall Mounting the Multiline Terminal ......... 5-49 4.10.1.3 Removing the Multiline Terminal from the Wall Mounted Base Plate.
  • Page 15 UNIVERGE SV8100 Issue 7.0 ___________________________________________________________________________________ UTR-1-1 USB Handset .............. 5-76 6.3.1 Handset Connection ..............5-76 6.3.2 USB Connection ..............5-76 6.3.3 Wall Mounting ................5-77 Section 7 Bluetooth Cordless Handset ............5-78 Bluetooth Cordless Handset (BCH) Interface ......5-78 Selecting a Location ..............5-79 Controls and Indicators ..............
  • Page 16 Issue 7.0 UNIVERGE SV8100 ___________________________________________________________________________________ term ® Section 10 D Cordless DECT (DTL-8R-1) ........5-100 10.1 Specifications ................5-101 10.2 Battery Safety .................5-102 10.3 Important Safety Instructions ...........5-103 10.4 Important Electrical Considerations .........5-104 10.5 Selecting a Location ..............5-107 10.6 Installation Precautions ............5-107 10.7 Connecting the Telephone Cords ..........5-107...
  • Page 17 UNIVERGE SV8100 Issue 7.0 ___________________________________________________________________________________ Section 2 PGD(2)-U10 ADP ................6-1 Using a PGD(2)-U10 ADP ............6-1 LED Indications ................6-2 Setting up PGD(2)-U10 ADP Connections ........6-2 Section 3 Background Music ..............6-10 Installing Background Music ............6-10 Section 4 Door Box ..................
  • Page 18 Issue 7.0 UNIVERGE SV8100 ___________________________________________________________________________________ Night Mode Selector Switch ............6-27 Connecting a Night Mode Selector Switch ........6-27 Section 10 Telephone Labeling ..............6-27 10.1 DESI Printer Sheets ..............6-27 10.1.1 Removing the Faceplate ............6-28 10.1.2 Replacing the Faceplate ............6-28 Section 11 Telephone Adapters ..............6-29 11.1 Using Adapters ................6-29...
  • Page 19 UNIVERGE SV8100 Issue 7.0 ___________________________________________________________________________________ 11.6.3 LED Display ................6-60 Section 12 Power Failure Telephones ............6-61 12.1 Power Failure ................6-61 12.2 Connector Pin-Outs on COIU Blade for Power Failure Circuits 6-62 12.3 Installing the Power Failure Telephones ........6-62...
  • Page 20: Issue

    Issue 7.0 UNIVERGE SV8100 ___________________________________________________________________________________ ___________________________________________________________________________________ xviii Table of Contents...
  • Page 21: Regulatory

    Regulatory BATTERY DISPOSAL The UNIVERGE SV8100 system includes the batteries listed below. When disposing of these batteries, Chassis, and/or Blades, you must comply with applicable regulations regarding proper disposal procedures. Table R-1 Battery Types and Quantities for Chassis and Blades...
  • Page 22 Contact your local waste management officials for other information regarding the environmentally sound collection, recycling and disposal of the battery contained in this product. The packaging for the UNIVERGE SV8100 system contains the following labels regarding proper disposal. PRODUCT PACKAGE LABELING CONTAINS NICKEL-CADMIUM BATTERY.
  • Page 23 For an overview of the supported features, refer to the detailed documentation that comes with this system, contact your local NEC representative or the support desk of NEC Unified Solutions.
  • Page 24 This product uses Lithium batteries. Do not use any other type. For an overview of the location of batteries used in these systems, the battery replacement or removal instructions, please refer to the UNIVERGE SV8100 System Hardware Manual. Regulatory...
  • Page 25: Chapter 1 Introduction To Sv8100

    Introduction to SV8100 ENERAL NFORMATION ECTION The SV8100 is a full-featured IP based communications system providing a rich feature set of existing system, with pure Voice over IP (VoIP) communications, across corporate Local and Wide Area Networks (LAN Chapter and WAN). The DT700 series telephones provide a converged infrastructure at the desktop, with a 10Base-T/100Base-TX connection to the LAN and built-in hub for a PC connection to the telephone itself.
  • Page 26 Issue 7.0 UNIVERGE SV8100 Figure 1-1 Simplified SV8100 System Connectivity Highlights of the UNIVERGE SV8100 are as follows: Pure IP System capable TDM configuration The SV8100 supports both pure IP switching (peer-to-peer connections) and Time Division Switching. The pure IP switching is provided for communications between DT700 series telephones and for CCIS / Remote Unit connections with other SV8100.
  • Page 27 UNIVERGE SV8100 Issue 7.0 MF senders / receivers 10/100 Ethernet Port 2 Control Relays MOH Input Port Paging Output Port In-Mail (VMDB) VoIP. In addition, by means of advanced LSI technology, size of the CPU blade is minimized, O&M NIC port (10/100M) is built in and VoIPDB which has VoIP NIC port (Gigabit Ethernet) is mountable without additional slots in the chassis.
  • Page 28: Section 2 Equipment List

    Issue 7.0 UNIVERGE SV8100 QUIPMENT ECTION The following tables list all equipment for the SV8100 systems. Table 1-1 Chassis Equipment List Equipment Name Equipment Description Product Code CHS2U 19” Chassis (6-slot) SV8100 CHS2U GW 9.5” Chassis (3-slot) SV8100 MPS7101 Power Supply Unit for 19” Chassis (2U)
  • Page 29 UNIVERGE SV8100 Issue 7.0 Table 1-4 Blade Equipment List Equipment Name Abbreviations Equipment Description Product Code CD-CP00 Main Processor Blade for KTS SV8100 PZ-BS10 BUS0 Expansion Chassis Interface Unit, 3-jack SV8100 PZ-BS11 BUS1 Expansion Chassis Interface Unit, 1-jack SV8100 PZ-VM21...
  • Page 30 Issue 7.0 UNIVERGE SV8100 Table 1-5 Cable Equipment List Equipment Name Equipment Description Product Code RS CONSOLE CA-A MAT (PCPro) Cable 6.6 ft. (2.0m) SV8100 RS NORM-4S CA-F RS-232C Cable (normal) 13.1 ft (4m) SV8100 RS RVS-15S CA-F RS-232C Cable (reverse) 49.2 ft (15.0m)
  • Page 31 UNIVERGE SV8100 Issue 7.0 Table 1-6 Digital Multiline Terminal (DT300 Series) Equipment List (Continued) Equipment Name Equipment Description Product Code 8LK-L (BK) UNIT 8-button Line Key Unit SV8100 8LK-L (WH) UNIT 8LKD (LD)-L (BK) UNIT DESI-less 8-button Line Key Unit/LCD Unit...
  • Page 32 Issue 7.0 UNIVERGE SV8100 Table 1-8 DT300/DT700 Series Optional Equipment List (Continued) Equipment Name Equipment Description Product Code PSA-L (BK) UNIT SV8100 PSA-L (WH) UNIT BCH-L (BK) UNIT Bluetooth Cordless Handset SV8100 12LK-L (BK) KIT 12-button Line Key Kit SV8100...
  • Page 33 UNIVERGE SV8100 Issue 7.0 Table 1-8 DT300/DT700 Series Optional Equipment List (Continued) Equipment Name Equipment Description Product Code Panel (Silver-Base)-L UNIT Color Side Panel for Base (Silver) SV8100 Panel (Silver-VLCD)-L UNIT Color Side Panel for Value Telephone LCD SV8100 (Silver)
  • Page 34 Issue 7.0 UNIVERGE SV8100 Table 1-8 DT300/DT700 Series Optional Equipment List (Continued) Equipment Name Equipment Description Product Code 12LKSoft-L (BK) SET 12LK without Soft Key SV8100 12LKSoft-L (WH) SET 12LK(STD)-L (BK) SET 12LK SV8100 12LK(STD)-L (WH) SET TKPANEL(STD)-L (BK) UNIT...
  • Page 35 UNIVERGE SV8100 Issue 7.0 Table 1-8 DT300/DT700 Series Optional Equipment List (Continued) Equipment Name Equipment Description Product Code KeyKitPanel(V)-L Color face panel for Value (Dark Brown SV8100 (D-Brown-M) Unit Metallic) 1 set consists 10 of panels LKPANEL(12BTN)-L Color LK panel (12button) for Value(...
  • Page 36 Issue 7.0 UNIVERGE SV8100 Table 1-8 DT300/DT700 Series Optional Equipment List (Continued) Equipment Name Equipment Description Product Code PANEL(C Gold-SLCD)-L Color side panel for Sophi LCD SV8100 UNIT (Champagne Gold) 1 set consist of 10 pair of panels. A pair includes (1) left and (1)
  • Page 37 UNIVERGE SV8100 Issue 7.0 Table 1-8 DT300/DT700 Series Optional Equipment List (Continued) Equipment Name Equipment Description Product Code HandsetCord(25FT)-L (BK) Spare Handset Cord 25 Feet SV8100 HandsetCord(25FT)-L (WH) HandsetHanger-L (BK) SET Spare Handset Hanger SV8100 HandsetHanger-L (WH) SET ITL (Value)-Base-1 unit...
  • Page 38 Issue 7.0 UNIVERGE SV8100 1 - 14 Introduction to SV8100...
  • Page 39: System Block Diagram

    SV8100 System Specifications ENERAL NFORMATION ECTION This chapter provides detailed specifications for the SV8100 system technician. The technician should review this information carefully before installing the system. Chapter YSTEM LOCK IAGRAM ECTION Figure 2-1 SV8100 System Block Diagram shows the Blades that can be installed in the chassis and the number of channels supported when the Blade is installed.
  • Page 40 Issue 7.0 UNIVERGE SV8100 Table 2-1 List of Abbreviations (Continued) Abbreviation Description Conference Bridge Blade (PVA) Central Processing Unit Direct Inward Dialing DIOP DID/OPX Blade Digital Multiline Terminal Interface Blade DLCB Expansion Digital Multiline Terminal Interface Blade on DLC Device Registration Server (on CPU)
  • Page 41 UNIVERGE SV8100 Issue 7.0 Table 2-1 List of Abbreviations (Continued) Abbreviation Description Power Failure Transfer Phase Locked Oscillator (on CPU) Property Management System Primary Rate Interface Primary Rate Interface Blade Personal Station PSTN Adapter (analog) Packet Voice Application Router Blade...
  • Page 42 Issue 7.0 UNIVERGE SV8100 Figure 2-1 SV8100 System Block Diagram 2 - 4 SV8100 System Specifications...
  • Page 43: Maximum System Capacities

    UNIVERGE SV8100 Issue 7.0 AXIMUM YSTEM APACITIES ECTION The CHS2U is a compact 19” chassis that has six universal slots, one expansion slot and one MPS7101 (power supply unit). When the CD-CP00 is installed in the first CHS2U, it is referred to as the Controlling Chassis. Additional chassis, referred to as Expansion Chassis, can be installed to increase the capacity of the system to meet the customer’s business needs.
  • Page 44: System Configuration - Sv8100

    Issue 7.0 UNIVERGE SV8100 Table 2-2 SV8100 Maximum System Capacities – Trunks/Ports/Channels 9.5” 19” Chassis Chassis System Number of: Maximum (CPU + 2 (6 Slots) (12 Slots) (18 Slots) (24 Slots) Slots) 96 *1 DTMF Receivers VoIP Channels 16 channels...
  • Page 45 UNIVERGE SV8100 Issue 7.0 The 9.5” chassis graphics shown in the horizontal position are for illustration purposes only. Actual positioning/ mounting must be vertical. 6 Slots 18 Slots 24 Slots IP Connection Figure 2-3 19” Controlling and Expansion Chassis System Hardware Manual...
  • Page 46 Issue 7.0 UNIVERGE SV8100 Table 2-3 Maximum System Capacities – Chassis shows the maximum number of chassis and related equipment that can be installed in a system. Table 2-3 Maximum System Capacities – Chassis 19” 19” 19” Chassis Hardware Chassis...
  • Page 47 UNIVERGE SV8100 Issue 7.0 Table 2-4 Maximum System Capacities – Blades shows the maximum number for each blade that can be installed in a system. This is determined by the maximum blade configuration allowed. When installing single line sets, DISA, or tie lines, CPU circuits must be allocated for DTMF receivers.
  • Page 48 Issue 7.0 UNIVERGE SV8100 Table 2-4 Maximum System Capacities – Blades (Continued) 19” 19” 19” 9.5” Chassis Hardware Chassis Chassis Chassis without with CPU Comments Number of Slot(s) for Interface 3 Slots 5 Slots 6 Slots 23 Slots Package CD-4LCA –...
  • Page 49 UNIVERGE SV8100 Issue 7.0 Table 2-4 Maximum System Capacities – Blades (Continued) 19” 19” 19” 9.5” Chassis Hardware Chassis Chassis Chassis without with CPU Comments Number of Slot(s) for Interface 3 Slots 5 Slots 6 Slots 23 Slots Package CD-4DIOPB...
  • Page 50 Issue 7.0 UNIVERGE SV8100 Table 2-5 Daughter Board Combinations shows each blade and associated daughter board combinations. The daughter boards that can be mounted on specific blades are indicated by a checkmark. For example, the CD-LTA can have a PZ-2BRIA or the PZ-4COTE daughter board mounted.
  • Page 51 OWER ASED ALCULATOR HART ECTION The Univerge SV8100 system uses two types of power factors. For a single chassis chart refer to Table 2-6 Board Power Factor. For the maximum number of specific blades per package, see Table 2-7 Maximum Number of Package Installed.
  • Page 52 Issue 7.0 UNIVERGE SV8100 Table 2-8 Terminal Power Factor Terminal Power Factor 19 inch Chassis =<80 Item Power Factor DTL-24D-1 TEL DTL-8LD-1 TEL BHA-L Unit ADA-L UNIT APR UNIT BCH-L (BK) UNIT PSA-L( ) 8LK-L UNIT DCL-60-1 CONSOLE ITL-320C-1 TEL...
  • Page 53 UNIVERGE SV8100 Issue 7.0 Table 2-9 IP Terminal Power Chart Label Indication IEEE802. Maximum Current Without Options (Maximum Current with All Options) Terminal Class 48VDC 24VDC 48VDC 24VDC ITL-12CG-3 TEL Class 3 230mA 11.04W 450mA 10.8W 102mA 4.9W 192mA 4.62W...
  • Page 54 Issue 7.0 UNIVERGE SV8100 Table 2-11 TDM terminal Power Chart Power TDM Terminal Consumption DTL-2E-1 1.0W DTL-6DE-1 1.1W DTL-8LD-1 2.2W DTL-12D-1 2.0W DTL-24D-1 2.0W DTL-32D-1 2.4W 2 - 16 SV8100 System Specifications...
  • Page 55: Cabling

    UNIVERGE SV8100 Issue 7.0 YSTEM EQUIREMENTS AND PECIFICATIONS ECTION Cabling This section provides cabling requirements and specifications for various equipment used in the SV8100 system. Figure 2-4 Connecting the DLC Using Twisted 2-Pair Cable is a diagram of the chassis connected with each of the multiline terminals and single line telephones by a separate twisted 1-pair cable or 2-pair cable (only for Multiline Terminals).
  • Page 56 Issue 7.0 UNIVERGE SV8100 Table 2-12 DT300 Series Loop Resistance and Cable Length (Continued) By Twisted 1-Pair By Twisted 1-Pair Cable (without Cable (with AC Terminal or Adapter AC Adapter) Adapter) 24 AWG 24 AWG DTL-24D-1(BK) TEL 1,969 ft (600m) 6,562 ft (2000m)
  • Page 57 UNIVERGE SV8100 Issue 7.0 term term Table 2-14 D Series i or D IP Terminal Loop Resistance and Cable Length Maximum Maximum By Twisted By Twisted By Twisted By Twisted Loop Loop 1-Pair Cable 2-Pair Cable 1-Pair Cable 2-Pair Cable...
  • Page 58: Power Requirements

    Issue 7.0 UNIVERGE SV8100 Table 2-16 Cabling Requirements Connected Equipment Cable Music on Hold and Background Music Sources Hi-Fi Shielded Audio Cable External Amplifier Hi-Fi Shielded Audio Cable ITL Cabling Cat 5 Straight Data Network Cable – 328.1 ft (100m) maximum distance.
  • Page 59: Power Supply Consumption

    UNIVERGE SV8100 Issue 7.0 VA @ 230V: Base chassis= , Expansion chassis= , total 276VA 276VA 1104VA KWh @ AC Input I x 230V/1000: Base chassis=0.276 KWh, Expansion chassis=0.276 KWh, total 1.104 KWh BTU (KWh x 3413): Base chassis= , Expansion chassis=...
  • Page 60: Outside Line Types

    Recommended Long Term Humidity: 10 ~ 95% RH Outside Line Types The following outside lines can be used with the UNIVERGE SV8100 system. 4-wire, E&M Tie Lines (Type I or V, Dial Pulse, or DTMF) Digital Trunk T1/FT1 (Loop Start, Tie Line (E&M), or DID Signaling)
  • Page 61: Network

    Network Time Division Multiplexing (TDM) allows transmission of data and voice simultaneously over one communications medium. The specifications that the UNIVERGE SV8100 system uses for switching, clock, data bus, and timeframe are shown below. TDM Switching: PCM (A Law) TDM Clock: 2.048 MHz TDM Data Bus: 8 bit TDM Timeframe: 125 µs.
  • Page 62: Electra Elite Ipk Terminals And Equipment

    Issue 7.0 UNIVERGE SV8100 5.5.4 Electra Elite IPK Terminals and Equipment The voltage, current, and ring signal for the Electra Elite IPK Multiline Terminals, Single Line Telephone equipment, and AP(A)-R/AP(R)-R Units are listed below: Multiline Terminal Voltage: -11 ~ -26 Vdc...
  • Page 63: Series I Terminals

    Dual-Tone Multifrequency (DTMF) Address Signaling DTMF signaling includes push button or Touchtone dialing. When a key on a telephone is pushed, two tones (one high frequency and one low frequency) are provided. In the UNIVERGE SV8100 system, the following DTMF specifications are used. Frequencies Two sinusoidal frequencies are provided, one from the high frequency group and one from the low frequency group.
  • Page 64: External Equipment Connection

    Issue 7.0 UNIVERGE SV8100 Rise Time: Within 5 ms. Duration of Dual Frequency Signal: 110 ms. default/60 ms. minimum Interdigital Time: 140 ms. default/45 ms. minimum Nominal High Group Frequencies (Hz) 1209 1336 1477 Nominal Low Group Frequencies (Hz) 5.6.3...
  • Page 65: External Tone Ringer/Night Chime Output

    5.6.10 Relay Contact All Relay Contact Ratings: 500 mA, 24Vdc Battery Backup The UNIVERGE SV8100 system has battery backup functions for system backup and for memory backup. 5.7.1 System Backup (Optional) During a power failure, the system can be backed up using the...
  • Page 66: Weights And Dimensions

    Issue 7.0 UNIVERGE SV8100 Weights and Dimensions Table 2-18 SV8100 Weights and Dimensions on page 2-28 shows the shipping weight, height, width and depth of each SV8100 digital multiline term terminal, IP multiline terminal, D , Series i multiline terminal, chassis, assorted blades and adapters.
  • Page 67 UNIVERGE SV8100 Issue 7.0 Table 2-18 SV8100 Weights and Dimensions (Continued) Shipping Unit Height Width Depth Weight CD-8DLCA 5.89 oz 0.98 in 5.71 in 7.09 in (0.167 kg) (25 mm) (145 mm) (180 mm) PZ-8DLCB 4.41 oz 0.60 in 4.72 in 5.12 in...
  • Page 68 Issue 7.0 UNIVERGE SV8100 Table 2-18 SV8100 Weights and Dimensions (Continued) Shipping Unit Height Width Depth Weight CHS BASE UNIT 21.87 oz 23.23 in 17.72 in 10.43 in (0.62 kg) (590 mm) (450 mm) (265 mm) CHS2U BLANK SLOT COVER KIT 1.76 oz...
  • Page 69 UNIVERGE SV8100 Issue 7.0 Table 2-18 SV8100 Weights and Dimensions (Continued) Shipping Unit Height Width Depth Weight ITL-6DE-1 (BK) TEL 38.8 oz 4.41 in 7.05 in 8.86 in (1.1 kg) (112 mm) (179 mm) (225 mm) ITL-8LDE-1 (BK) TEL 63.66 oz 4.41 in...
  • Page 70 Issue 7.0 UNIVERGE SV8100 Table 2-18 SV8100 Weights and Dimensions (Continued) Shipping Unit Height Width Depth Weight DCL-60-1 (BK) CONSOLE 21.16 oz 3.23 in 5.39 in 8.82 in DCL-60-1 (WH) CONSOLE (.6 kg) (82 mm) (137 mm) (224 mm) PSA-L (BK) UNIT 10.58 oz...
  • Page 71: Chapter 3 Installing The Sv8100 Chassis

    Installing the SV8100 Chassis ENERAL NFORMATION ECTION This chapter contains information to help the technician install the chassis for the SV8100 system. The technician should be familiar with this section before installing any equipment. Chapter NSTALLING THE HASSIS ECTION The CHS2U-EU chassis has six universal blade slots for legacy line/trunk blade (Single Line Telephone Interface, Digital Multiline Terminal Interface, Central Office Trunk, ISDN PRI Interface, etc.), In-skin Application Blades (In-skin UMS, In-Skin Router, etc.).
  • Page 72 Issue 7.0 UNIVERGE SV8100 Universal Slot for Legacy Line/Trunk blades and Application blades (six slots). When used as controlling chassis, the is mounted in CD-CP00 Slot 1 (shown). Slot for PZ-BS10/PZ-BS11 blade – Connection with CHS2U chassis Power Supply Unit (PSU)
  • Page 73 UNIVERGE SV8100 Issue 7.0 The CHS2U GW chassis has three universal blade slots for station, trunk and optional blades.The chassis can be wall-mounted or stand-mounted. The first part of the this chapter describes the differing types of mounting options and the rest of this section describes how to install the chassis.
  • Page 74: Wall Mounting The 19" Chassis

    Issue 7.0 UNIVERGE SV8100 Wall Mounting the 19” Chassis When wall mounting the chassis, ensure the wall can support the weight of the chassis (55 lbs per system chassis ---- including blades, cords, power supply, etc.). The chassis is secured to the wall with a wall mount bracket. Ensure that enough space is available to allow the installation of additional expansion chassis.
  • Page 75 UNIVERGE SV8100 Issue 7.0 Mark and drill the six holes required for a wall installation. Align screw holes in wall mount brackets with drilled holes. System Hardware Manual 3 - 5...
  • Page 76 Issue 7.0 UNIVERGE SV8100 Using six screws, secure the two wall mount brackets to the wall. Refer to Figure 3-6 Install Wall Mount Brackets with Screws for screw location. Figure 3-6 Install Wall Mount Brackets with Screws Using four screws, secure the metal fittings on the Left and Right sides of the 19”...
  • Page 77 UNIVERGE SV8100 Issue 7.0 Figure 3-7 Install Wall Mount Brackets with Screws System Hardware Manual 3 - 7...
  • Page 78 Issue 7.0 UNIVERGE SV8100 Align the metal fitting with the upper wall mount bracket. The lower metal fitting rests against the lower wall mount bracket. Secure the metal fitting and upper wall mount bracket with a single screw (see Figure 3-8 Secure Metal Fitting to Upper Wall Mount Bracket with a Screw).
  • Page 79 UNIVERGE SV8100 Issue 7.0 Figure 3-9 Secure Metal Fitting to Lower Wall Mount Bracket with Screws Attach the supplied cable support bracket to either end of the lower wall mount bracket with a single screw (refer to Figure 3-10 Attach Cable Support Bracket with Screw on page 3-10).
  • Page 80 Issue 7.0 UNIVERGE SV8100 Figure 3-10 Attach Cable Support Bracket with Screw The cable support bracket can be installed any of the four corners of the 19” chassis (refer to Figure 3-11 Attach Cable Support Bracket with Screw on page 3-11).
  • Page 81 UNIVERGE SV8100 Issue 7.0 Figure 3-11 Attach Cable Support Bracket with Screw Connect the ground wire to all chassis. Refer to 2.7.5 Install 19” Chassis Grounding on page 3-52 for complete details on grounding the system. Refer to 2.7 Installing the 19” Chassis on page 3-39...
  • Page 82: Floor Mounting The 19" Chassis

    Issue 7.0 UNIVERGE SV8100 Floor Mounting the 19” Chassis The CHS2U controlling and expansion chassis can be mounted on the floor using the CHS BASE UNIT and the CHS2U JOINT BRACKET KIT. 2.2.1 CHS2U Chassis Installation Use the template shown in...
  • Page 83 UNIVERGE SV8100 Issue 7.0 Figure 3-13 Secure CHS BASE UNIT with Anchor Bolts Install the five rubber feet to the bottom of the chassis. Figure 3-14 Install Rubber Feet Position the chassis on top of the CHS BASE UNIT. Secure the chassis to the CHS BASE UNIT using eight screws supplied with the CHS2U JOINT BRACKET KIT.
  • Page 84: Multiple Chs2U Chassis Installation

    Issue 7.0 UNIVERGE SV8100 Figure 3-15 Install CHS2U JOINT BRACKET KIT Connect the ground wire to all chassis. Refer to 2.7.5 Install 19” Chassis Grounding on page 3-52 for complete details on grounding the system. Refer to 2.7 Installing the 19” Chassis on page 3-39...
  • Page 85 UNIVERGE SV8100 Issue 7.0 Install the five rubber feet to the bottom of each chassis. Figure 3-16 Install Rubber Feet Using supplied screws in the CHS2U JOINT BRACKET KIT, attach metal brackets to both ends of the 19” chassis and the CHS BASE UNIT.
  • Page 86: Stand Mounting The 19" Chassis

    Issue 7.0 UNIVERGE SV8100 Connect the ground wire to all chassis. Refer to 2.7.5 Install 19” Chassis Grounding on page 3-52 for complete details on grounding the system. Refer to 2.7 Installing the 19” Chassis on page 3-39 to continue...
  • Page 87 UNIVERGE SV8100 Issue 7.0 Expansion Plate Figure 3-19 Secure CHS2U Chassis to CHS2U STAND KIT with Screws Using supplied screws, secure the CHS2U STAND KIT to the floor (refer to Figure 3-20 Secure Stand Mount to Floor with Screws on page 3-18).
  • Page 88 Issue 7.0 UNIVERGE SV8100 Figure 3-20 Secure Stand Mount to Floor with Screws Connect the ground wire to all chassis. Refer to 2.7.5 Install 19” Chassis Grounding on page 3-52 for complete details on grounding the system. Refer to 2.7 Installing the 19” Chassis on page 3-39...
  • Page 89: Multiple Chs2U Chassis Installation

    UNIVERGE SV8100 Issue 7.0 2.3.2 Multiple CHS2U Chassis Installation Expansion chassis (maximum of three) can be added to the CHS2U STAND KIT and will require an additional CHS2U STAND KIT (EXT) per chassis. Install the five rubber feet to the bottom of each chassis.
  • Page 90 Issue 7.0 UNIVERGE SV8100 Expansion Plates Figure 3-22 Install Additional CHS2U STAND KIT (EXT) Metal brackets from the CHS2U JOINT BRACKET KITs will be required to secure the top end of the chassis with screws. See Figure 3-23 Install Additional CHS2U STAND KIT (EXT) on page 3-21.
  • Page 91 UNIVERGE SV8100 Issue 7.0 Metal Brackets Figure 3-23 Install Additional CHS2U STAND KIT (EXT) Using supplied screws, secure the CHS2U STAND KIT to the floor (refer to Figure 3-23 Install Additional CHS2U STAND KIT (EXT) on page 3-21). Connect the ground wire to all chassis. Refer to 2.7.5 Install...
  • Page 92: Rack Mounting The 19" Chassis

    Issue 7.0 UNIVERGE SV8100 Rack Mounting the 19” Chassis A single or multiple chassis can be rack mounted. Controlling and Expansion chassis can be racked mounted by stacking them horizontally. The 19” chassis requires two rack mount brackets per chassis for mounting.
  • Page 93 UNIVERGE SV8100 Issue 7.0 Repeat for additional chassis mounting. Figure 3-25 Rack Mount Bracket Installed 19” CHS2U Carefully slide the chassis into desired location in the rack. Make sure the hooks on the mounting bracket are inserted into the back of the chassis, securing it in place.
  • Page 94: Wall Mounting The 9.5" Chassis

    Issue 7.0 UNIVERGE SV8100 Connect the ground wire to all chassis. Refer to 2.7.5 Install 19” Chassis Grounding on page 3-52 for complete details on grounding the system. Refer to 2.7 Installing the 19” Chassis on page 3-39 to continue installation of the chassis or, Chapter 5 paragraph 2.2 Installing an...
  • Page 95: Option 1

    UNIVERGE SV8100 Issue 7.0 Figure 3-28 Wall Mount Spacing Guide (9.5” Chassis) 2.5.1 Option 1 Use the template shown in Figure 3-28 Wall Mount Spacing Guide (9.5” Chassis) on page 3-25 for required spacing before drilling. Plywood should first be installed on the wall where the chassis will be positioned.
  • Page 96 Issue 7.0 UNIVERGE SV8100 Figure 3-29 9.5” Mounting Brackets and Metal Expansion Fitting Secure the bracket halves to the expansion fitting using the four supplied screws (refer to Figure 3-29 9.5” Mounting Brackets and Metal Expansion Fitting on page 3-26).
  • Page 97 UNIVERGE SV8100 Issue 7.0 Brackets Secured in Mounting Position with Screws). Figure 3-30 Brackets Secured in Mounting Position with Screws Rotate the brackets into the mounting position. Using the same screws, secure the metal brackets to the bracket assembly (refer to...
  • Page 98 Issue 7.0 UNIVERGE SV8100 Figure 3-31 Remove End Brackets Using four screws, secure bracket assembly to the four pre-drilled holes in the wall. Fit the precut holes on the 9.5” chassis over the metal tabs (refer to Figure 3-32 Attach 9.5” Chassis to Wall Mounting Bracket on page 3-29).
  • Page 99 UNIVERGE SV8100 Issue 7.0 Figure 3-32 Attach 9.5” Chassis to Wall Mounting Bracket Using the screws removed earlier, install the end brackets to secure the 9.5” chassis to the mounted bracket assembly. Figure 3-33 Install End Brackets Connect grounding wire to chassis. Refer to 2.8 Installing the...
  • Page 100: Option 2

    Issue 7.0 UNIVERGE SV8100 Refer to 2.8 Installing the 9.5” Chassis on page 3-54 continue installation of the chassis or 2.2 Installing an Extension or Trunk Blade on page 4-4 for installation of blades. 2.5.2 Option 2 Use the template shown in Figure 3-28 Wall Mount Spacing Guide (9.5”...
  • Page 101 UNIVERGE SV8100 Issue 7.0 Figure 3-34 Install Screws (Option 2) System Hardware Manual 3 - 31...
  • Page 102 Issue 7.0 UNIVERGE SV8100 Align the bracket halves with the precut holes in the metal expansion fitting provided (refer to Figure 3-35 9.5” Mounting Brackets and Metal Expansion Fitting). Figure 3-35 9.5” Mounting Brackets and Metal Expansion Fitting Secure the bracket halves to the expansion fitting using the four supplied screws (refer to Figure 3-35 9.5”...
  • Page 103 UNIVERGE SV8100 Issue 7.0 two brackets in the shipped position (refer to Figure 3-36 Brackets Secured in Mounting Position with Screws). Figure 3-36 Brackets Secured in Mounting Position with Screws Rotate the brackets into the mounting position. Using the same...
  • Page 104 Issue 7.0 UNIVERGE SV8100 Figure 3-37 Remove End Brackets Fit the precut holes on the 9.5” chassis over the metal tabs (refer to Figure 3-38 Attach 9.5” Chassis to Wall Mounting Bracket on page 3-35). 3 - 34 Installing the SV8100 Chassis...
  • Page 105 UNIVERGE SV8100 Issue 7.0 Figure 3-38 Attach 9.5” Chassis to Wall Mounting Bracket Using the screws removed earlier, install the end brackets to secure the 9.5” chassis to the mounted bracket assembly. Figure 3-39 Install End Brackets System Hardware Manual...
  • Page 106: Stand Mounting The 9.5" Chassis

    Issue 7.0 UNIVERGE SV8100 Using the key-holes as a guide, slide the assembled unit over the screws previously installed in the wall (refer to Figure 3-34 Install Screws (Option 2) on page 3-31). Connect grounding wire to chassis. Refer to 2.8 Installing the...
  • Page 107 UNIVERGE SV8100 Issue 7.0 Figure 3-41 Attach 9.5” Stand Mount Bracket Figure 3-42 Attach Remaining 9.5” Stand Mount Bracket System Hardware Manual 3 - 37...
  • Page 108 Figure 3-44 Secure the 9.5” Stand Mounting with Screws on page 3-39). To prevent possible damage to the 9.5” chassis due to falling, NEC recommends the screws be installed in the stand mount brackets as soon as possible. 3 - 38 Installing the SV8100 Chassis...
  • Page 109: Installing The 19" Chassis

    UNIVERGE SV8100 Issue 7.0 Figure 3-44 Secure the 9.5” Stand Mounting with Screws Connect grounding wire to chassis. Refer to 2.8 Installing the 9.5” Chassis on page 3-54 for complete details on grounding the system. Refer to 2.8 Installing the 9.5” Chassis on page 3-54...
  • Page 110: Unpacking The Equipment

    Inspect the equipment for any physical damage. If you are not sure about the function of a component, review the associated information within this manual. Contact your authorized NEC Sales Representative if you have additional questions. Note that the chassis does not initially contain any blades.
  • Page 111: Installing The 19" Controlling Chassis

    UNIVERGE SV8100 Issue 7.0 2.7.3 Installing the 19” Controlling Chassis Ensure the chassis is powered down. Do not remove or install this blade with the power on. Align the CD-CP00 blade with the Slot 1 guides of the Controlling Chassis.
  • Page 112: Installing Expansion Blades In The 19" Chassis (Optional)

    The EXIFU cable connects the Controlling Chassis and its EXIFU-B1 interface to the second, third, and fourth EXIFU-E1 interface. Use only the CAT 5 cables provided by NEC to make the connections between the Controlling and Expansion Chassis. The PZ-BS10 provides:...
  • Page 113: Connector Pin-Out On The Pz-Bs10/Pz-Bs11

    UNIVERGE SV8100 Issue 7.0 2.7.4.1 Connector Pin-Out on the PZ-BS10/PZ-BS11 Table 3-1 PZ-BS10/PZ-BS11 Connector Pin-Out RJ-61 Cable Connector PZ-BS10 – CN2, CN3, CN 4 PZ-BS11 – CN3 Pin No. Connection HW_UP (+) HW_UP (-) HW_DWN (+) FS (+) FS (-)
  • Page 114 Issue 7.0 UNIVERGE SV8100 From the left side of the chassis, pull cover outward to expose the expansion bay. Figure 3-49 Open Base Chassis Cover Pull the cover toward you to remove. Cover must be removed prior to installation of PZ-BS10 blade.
  • Page 115 UNIVERGE SV8100 Issue 7.0 Figure 3-51 PZ-BS10 Components Slide the PZ-BS10 blade into the chassis until resistance (back plane) is felt. Figure 3-52 Installing PZ-BS10 Blade in Expansion Bay Gently push until the blade seats and install the supplied retaining screw.
  • Page 116: Install The Pz-Bs11 Expansion Blade In The Chs2U Expansion Chassis

    Issue 7.0 UNIVERGE SV8100 Align the door tabs with hinges and reattach the cover. Figure 3-53 PZ-BS10 Blade Installed Close the PZ-BS10 cover. Figure 3-54 PZ-BS10 Installed (Cover Closed) 2.7.4.3 Install the PZ-BS11 Expansion Blade in the CHS2U Expansion Chassis For the Expansion Chassis to function, the PZ-BS10 blade must be installed in Controlling Chassis.
  • Page 117 UNIVERGE SV8100 Issue 7.0 Locate the door positioned on the left end (expansion bay) of the Expansion Chassis. Expansion Bay Figure 3-55 PZ-BS11 Expansion Bay in Expansion Chassis From the left side of the chassis, pull cover outward to expose the expansion bay.
  • Page 118 Issue 7.0 UNIVERGE SV8100 Pull the cover toward you to remove. Cover must be removed to install PZ-BS11 blade. Align the PZ-BS11 blade with the guides located within the expansion bay. Figure 3-57 PZ-BS11 Blade Guides Slide the PZ-BS11 blade into the chassis until resistance (back plane) is felt.
  • Page 119 UNIVERGE SV8100 Issue 7.0 Align the door tabs with hinges and reattach the cover. Figure 3-59 PZ-BS11 Blade Installed Close the PZ-BS11 blade cover. Figure 3-60 PZ-BS11 Installed (Cover Closed) System Hardware Manual 3 - 49...
  • Page 120: Connect The Controlling And Expansion Chassis

    PZ-BS10 Figure 3-61 19” Expansion Chassis Interface Units Ensure Controlling and Expansion chassis are powered down. Using the NEC provided CAT5 straight-through cable(s), attach one end to each Expansion Chassis CN2 connector on the PZ-BS11 blade (see Figure 3-62 System Expansion Cabling on page 3-51.
  • Page 121 UNIVERGE SV8100 Issue 7.0 Install in Expansion Chassis Install in Expansion Chassis Install in Expansion Chassis Install in Controlling Chassis Figure 3-62 System Expansion Cabling Repeat for additional Expansion Chassis. System Hardware Manual 3 - 51...
  • Page 122: Install 19" Chassis Grounding

    Issue 7.0 UNIVERGE SV8100 2.7.5 Install 19” Chassis Grounding From the factory, the SG, ETH and PBXG grounds are located inside the chassis and are connected to the FG ground (frame ground) on the back of the chassis. Each chassis (CHS2U) in the system must be grounded separately using the procedure listed below.
  • Page 123: Install Ac Power Cords

    UNIVERGE SV8100 Issue 7.0 FG Lugs Electrical Service Ground Figure 3-64 19” Chassis Grounding Lug (Multiple-Chassis) 2.7.7 Install AC Power Cords Locate the supplied AC power cord and attach to the AC Inlet located on the back of the Controlling Chassis.
  • Page 124: Install Ac Power Cords On Multiple-Chassis (Optional)

    Issue 7.0 UNIVERGE SV8100 2.7.8 Install AC Power Cords on Multiple-Chassis (Optional) Locate the supplied AC power cords and attach to the AC Inlets located on the back of the Controlling and Expansion Chassis. AC Power Cords to AC Inlets Figure 3-66 Install 19”...
  • Page 125: Install Ac Power Cord 9.5" Chassis

    UNIVERGE SV8100 Issue 7.0 back side of the chassis to an electrical service ground (such as a cold water pipe). Figure 3-67 CHS2U GW Chassis (Rear View) 2.8.1 Install AC Power Cord 9.5” Chassis Locate the supplied AC power cord and attach to the AC Inlet located...
  • Page 126: Battery Connection

    Issue 7.0 UNIVERGE SV8100 ATTERY ONNECTION ECTION There are two types of battery connection to provide battery life in the event of a power failure, the internal battery and an external battery with CHS LARGE BATT BOX. Installing the Internal Batteries...
  • Page 127 UNIVERGE SV8100 Issue 7.0 Remove access panel containing the fan. Refer to Figure 3-69 Removing Access Panel Figure 3-70 Access Panel Removed. Figure 3-69 Removing Access Panel Figure 3-70 Access Panel Removed System Hardware Manual 3 - 57...
  • Page 128 Issue 7.0 UNIVERGE SV8100 Using tie wraps, secure CHS2U BATT CABLE INT in cable guide bracket (refer to Figure 3-71 Installing Cable Guide). Figure 3-71 Installing Cable Guide With supplied screw, install cable guide in chassis (refer to Figure 3-72 Installing Cable Guide).
  • Page 129 UNIVERGE SV8100 Issue 7.0 Install two 2.3 AH-12V batteries (locally procured) into the CHS2U BATT MTG KIT (refer to Figure 3-73 Installing Two Batteries). The first battery must be installed on the left side, then slid to the right due to an installation tab on the mounting kit.
  • Page 130 Issue 7.0 UNIVERGE SV8100 Connect the provided battery cables to the batteries (refer to Figure 3-74 Installing Battery Cable). Figure 3-74 Installing Battery Cable Connect CHS2U BATT CABLE INT to battery connector (refer to Figure 3-75 Connecting CHS2U BATT CABLE INT).
  • Page 131 UNIVERGE SV8100 Issue 7.0 Install CHS2U BATT MTG KIT into CHS2U chassis and tighten the retaining screws (see Figure 3-76 Installing Battery Tray into CHS2U Chassis). Figure 3-76 Installing Battery Tray into CHS2U Chassis Reinstall access panel containing the fan and secure with supplied screw...
  • Page 132: Installing The External Batteries

    Issue 7.0 UNIVERGE SV8100 Installing the External Batteries An optional (locally procured), external battery source can be used to provide power in the event of a power failure. CHS LARGE BATT BOX (Backup time = Three Hours for 30 Terminals)
  • Page 133 UNIVERGE SV8100 Issue 7.0 Figure 3-78 Floor Mount Spacing Guide Mark and drill the four holes required for installing the CHS BASE UNIT. Align bolt holes in CHS BASE UNIT (see Figure 3-78 Floor Mount Spacing Guide on page 3-63) with holes drilled in floor and secure using four anchor bolts.
  • Page 134: Battery Installation

    Issue 7.0 UNIVERGE SV8100 Figure 3-79 Installing the CHS LARGE BATT BOX using the CHS2U JOINT BRACKET KIT Secure the CHS LARGE BATT BOX to the CHS BASE UNIT using the CHS2U JOINT BRACKET KIT. Refer to Figure 3-79 Installing the CHS LARGE BATT BOX using the CHS2U JOINT BRACKET KIT on page 3-64.
  • Page 135 UNIVERGE SV8100 Issue 7.0 Remove two screws from front of Battery Tray Suppressor. Refer to Figure 3-81 Removing Battery Tray Suppressor. Figure 3-81 Removing Battery Tray Suppressor Slide Battery Tray Suppressor outward to remove. Slide Battery Tray(s) out of CHS LARGE BATT BOX.
  • Page 136 Issue 7.0 UNIVERGE SV8100 Remove two screws and remove the Battery Tray Bracket. Refer to Figure 3-83 Removing Battery Tray Bracket. Figure 3-83 Removing Battery Tray Bracket Refer to Figure 3-84 Connecting Battery Cables for connection of battery cable to battery terminals. Repeat for additional battery connection.
  • Page 137 UNIVERGE SV8100 Issue 7.0 Install batteries into Battery Tray. Refer to Figure 3-85 Connecting Battery Cables. Using two screws, install the Battery Tray Bracket. Refer to Figure 3-83 Removing Battery Tray Bracket on page 3-66. Figure 3-85 Connecting Battery Cables Insert Battery Connection Cable into cable guides.
  • Page 138: Chs Large Batt Box To Chs2U Connection

    Issue 7.0 UNIVERGE SV8100 Figure 3-86 Connecting Battery Cables Insert tabs on cover into holes on CHS LARGE BATT BOX. Slide the cover left until seated and tighten the screw. Refer to Figure 3-87 Installing Cover Battery. Figure 3-87 Installing Cover Battery 3.2.3...
  • Page 139 UNIVERGE SV8100 Issue 7.0 Remove fan access panel from rear of CHS2U chassis. Refer Figure 3-88 Removing Fan Access Panel. Figure 3-88 Removing Fan Access Panel Connect one end of Battery Connection Cable to Battery Connector on rear of Basic and Expansion chassis.
  • Page 140 Issue 7.0 UNIVERGE SV8100 Basic Expansion Figure 3-90 Single CHS LARGE BATT BOX Connection Basic Expansion Figure 3-91 Dual CHS LARGE BATT BOX Connection 3 - 70 Installing the SV8100 Chassis...
  • Page 141 UNIVERGE SV8100 Issue 7.0 Insert the access panel tab into the rear of the CHS1U-US chassis running the Battery Connection Cable through the cutout. Secure panel with the retaining screw. Refer to Figure 3-92 Install the Fan Access Panel. Figure 3-92 Install the Fan Access Panel Connect grounding and AC power cables.
  • Page 142: Installing The External Batteries 9.5" Chassis

    Issue 7.0 UNIVERGE SV8100 Installing the External Batteries 9.5” Chassis An optional, CHSGW SMALL BATT BOX can be installed to provide external battery power to the CHS2U GW chassis during a power failure. The short- term battery box will power the system for approximately 10 minutes.
  • Page 143 UNIVERGE SV8100 Issue 7.0 The metal bracket is placed on top of the batteries and able to hold them in place. Insert the metal tabs of the bracket into the slots on the side of the battery compartment and lower into place.
  • Page 144: Chsgw Small Batt Box To Chs2U Gw Connection

    Issue 7.0 UNIVERGE SV8100 Reattach the cover with the two screws previously removed. Figure 3-97 Reattaching the Top Cover Using Screws 3.3.2 CHSGW SMALL BATT BOX to CHS2U GW Connection Power down the CHS2U GW chassis. Ensure the CHS2U GW chassis is powered OFF.
  • Page 145: Chsgw Small Batt Box Fuse Replacement

    UNIVERGE SV8100 Issue 7.0 Secure the battery compartment to the chassis using the two screws provided and attach the battery cable to the 9.5” chassis. Figure 3-99 Attach to the CHS2U GW Chassis and Connect Battery Cable Reconnect AC power cable to rear of chassis.
  • Page 146 Issue 7.0 UNIVERGE SV8100 Unplug all the cable connectors from the battery box. Figure 3-100 Removing the CHSGW SMALL BATT BOX Loosen the two thumb screws on the battery box and remove the box by pulling on the two thumb screws.
  • Page 147: Remove And Install Cooling Fan

    CHS2U Chassis 4.1.1 Remove Cooling Fan To reduce the possibility of electrical shock or damage to equipment, NEC recommends powering Off the chassis and disconnecting the AC cable from the power source before removing the chassis cover. Ensure the chassis is powered down.
  • Page 148 Issue 7.0 UNIVERGE SV8100 Swing access panel outward and unplug fan power cable. See Figure 3-102 Opening Chassis Access Panel (19” Chassis). Fan Power Cable Plug Figure 3-102 Opening Chassis Access Panel (19” Chassis) Remove chassis access panel from rear of chassis.
  • Page 149 UNIVERGE SV8100 Issue 7.0 4.1.2 Install Cooling Fan Align replacement fan with holes and secure with two screws (refer to Figure 3-103 Chassis Access Panel Removed on page 3-78. Install cabling into retention clips (refer to Figure 3-103 Chassis Access Panel Removed on page 3-78 Insert access panel hinges into slots on rear of chassis.
  • Page 150 Issue 7.0 UNIVERGE SV8100 3 - 80 Installing the SV8100 Chassis...
  • Page 151: Chapter 4 Installing The Sv8100 Blades

    ENERAL NFORMATION ECTION This chapter contains information to help the technician install the blades for the UNIVERGE SV8100 system. The technician should be familiar with this section before installing any equipment. Chapter Slot Locations Each CHS2U has six slots. In the Controlling Chassis, the CD-CP00 must be installed in the first slot (slot 1).
  • Page 152 Issue 7.0 UNIVERGE SV8100 19” Controlling Chassis CPU Slot 19 “Expansion Chassis PZ-BS11 Slot 9.5 “ Chassis Figure 4-1 Chassis CPU and Expansion Slot Locations 4 - 2 Installing the SV8100 Blades...
  • Page 153: Installation

    UNIVERGE SV8100 Issue 7.0 ECTION NSTALLATION Pre-installation planning is essential. Advanced planning minimizes installation time, cost, and disruption of the customer business activities. Installation and Safety Precautions Observe the following precautions when installing the blades to avoid static electricity damage to hardware or exposure to hazardous voltages.
  • Page 154: Installing An Extension Or Trunk Blade

    Issue 7.0 UNIVERGE SV8100 Installing an Extension or Trunk Blade 2.2.1 Installing the Blades To install an extension/trunk blade with the system running: Insert the blade within the guide rail and push the blade securely into position. Tighten the thumb screws on either side of the blade.
  • Page 155 UNIVERGE SV8100 Issue 7.0 2.2.2 Order of Installing Extension Blades The order in which the station blades (CD-8DLCA, CD-16DLCA, PZ-8DLCB and CD-4LCA, CD-8LCA, PZ-8LCE) are physically inserted determines the numbering plan. To avoid unexpected extension/trunk numbering if the VoIP or Voice Mail daughter board registers...
  • Page 156: Order Of Installing Trunk Blades

    Issue 7.0 UNIVERGE SV8100 Table 4-2 Adding Daughter Board to Chassis Example Initial Blade Updated Blade Blade Extension Blade Extension Blade Blade Slot # Numbers Slot # Numbers CD-16DLCA 200~215 CD-16DLCA 200~215 CD-8DLCA 216~223 — — (no daughter board) CD-16DLCA...
  • Page 157 UNIVERGE SV8100 Issue 7.0 For example, if four blades are installed in the following order, the numbering plan below applies. Table 4-3 Trunk Blade Installation Order Example Order of Blade Slot Blade Line Circuits Installation Number CD-4COTA with PZ-4COTE CD-4COTA...
  • Page 158: Installing Cd-Prta (T1/Pri) Blades

    Issue 7.0 UNIVERGE SV8100 2.2.3.2 Installing CD-PRTA (T1/PRI) Blades The CD-PRTA (T1/PRI) Interface blade uses the first block of 24 consecutive trunks. For example, if an CD-4COTA and PZ-4COTE blade is installed for trunks 1~8, the CD-PRTA (T1/PRI) blade automatically uses trunks 9~32. If CD-4COTA and PZ-4COTE blades are installed for trunks 1~8 and 17~24, the CD-PRTA (T1/PRI) blade uses trunks 25~48.
  • Page 159: Blade Capacities

    UNIVERGE SV8100 Issue 7.0 Blade Capacities The universal architecture of the UNIVERGE SV8100 provides flexibility when installing blades. With the exception of the CD-CP00 and CC-CP00 blades, any blade can be installed in any slot. Table 2-4 Maximum System Capacities – Blades on page 2-9 (SV8100) provides a list of the blades and the maximum capacities with various chassis configurations.
  • Page 160: Performing A Hot Start

    Issue 7.0 UNIVERGE SV8100 2.6.2 Performing a Hot Start The section describes how to load system software from flash memory and customer data from RAM memory. IMPORTANT CONSIDERATIONS System software is loaded from flash memory and the customer data is loaded from RAM memory.
  • Page 161: Port Defaults

    UNIVERGE SV8100 Issue 7.0 2.6.3.2 Port Defaults With the default settings, the ports are assigned as follows: Table 4-4 Default Port Settings Port 1~99 : 200~298 Station Ports: Port 100~300 : 299~499 Port 301~512 : 500~5211 Port 1~99 : 201~299...
  • Page 162: Saving Your Configuration

    Issue 7.0 UNIVERGE SV8100 2.6.3.4 Saving Your Configuration When programming is completed, to exit out of the program option and save changes to the CD-CP00: 1. Press EXIT to exit the program options, if needed. 2. Press Speaker. Saving System Data is displayed if changes were made to system programming.
  • Page 163: Performing A Software Upgrade

    UNIVERGE SV8100 Issue 7.0 After reloading the customer data to the system, exit programming mode (this could take a minute or more to save the database), then reset the system by powering down and back up. If the system is not reset, not all the uploaded programming changes are in effect.
  • Page 164 Issue 7.0 UNIVERGE SV8100 IMPORTANT CONSIDERATIONS To save customer data prior to updating, a blank USB Memory is required. Insert the USB Memory into the USB Port on the CD-CP00 blade. Use Program 90-03 to save the software to the USB Memory. Note that a USB Memory can only hold one customer database.
  • Page 165 UNIVERGE SV8100 Issue 7.0 To perform a system software and firmware upgrade: Turn the system power off. Once the system has powered down, insert the USB Memory containing the software upgrade into the USB port on the CD-CP00. Push in and hold the Load button.
  • Page 166: Cd-Cp00 (Sv8100 Central Processing Unit)

    Issue 7.0 UNIVERGE SV8100 OMMON ONTROL LADES ECTION The blades described in this section control the common functions of the chassis. CD-CP00 (SV8100 Central Processing Unit) PZ-32IPLA PZ-64IPLA PZ-128IPLA Battery Fast Ethernet CN7 BGM/EXSP Control CN 10 USB CN5 Status LED1...
  • Page 167: Description

    UNIVERGE SV8100 Issue 7.0 PZ-32IPLA PZ-64IPLA Battery PZ-128IPLA CompactFlash PZ-VM21 PZ-ME50 Figure 4-4 CD-CP00 Blade with Daughter Boards Installed 3.1.1 Description The CD-CP00 controls all the functions and operations of the SV8100 system using the system software loaded into the CD-CP00 memory.
  • Page 168 Issue 7.0 UNIVERGE SV8100 PZ-BS10/PZ-BS11 Interface Circuit Main Processing 32-Bit CPU Circuit (MPC8248 @ 2 MHz) Time Switch, Optional Blade Control Circuit Backboard Interface Circuit The CD-CP00 provides: 200 trunk ports maximum 512 extension ports maximum – 512 ports digital/IP extensions maximum –...
  • Page 169 UNIVERGE SV8100 Issue 7.0 MF Signal Sender (Sends caller information to CO for E911) Call Progress Tone Detection C-Channel Control Conference: 64 Channels Caller ID Receiver; 32 Channels Caller ID Generator; 4 or 10 Channels for Analog Stations This can be expanded up to 20 by disabling 32 channels of the...
  • Page 170: Installation

    Issue 7.0 UNIVERGE SV8100 RTP Forwarding VoCoder Conversion 3.1.2 Installation Each SV8100 system must have the CD-CP00 installed in Slot 1 of the Controlling Chassis. IMPORTANT INSTALLATION NOTES The chassis power must be off when installing or removing the CD-CP00.
  • Page 171 UNIVERGE SV8100 Issue 7.0 Figure 4-5 CD-CP00 Battery Installation Refer to Figure 4-4 CD-CP00 Blade with Daughter Boards Installed on page 4-17 to Install the PZ-VM21, PZ-ME50 and/or PZ-32IPLA/PZ-64IPLA/PZ-128IPLA daughter board, if required. Ensure the power supply is OFF, then slide the CPU into the CCPU slot in the Controlling Chassis.
  • Page 172: Switch Settings

    Issue 7.0 UNIVERGE SV8100 Customer information is stored in the RAM memory and, in case of a power failure, will be restored. The lithium battery in the system saves the RAM memory when power is lost. 3.1.3 Switch Settings Refer to...
  • Page 173 UNIVERGE SV8100 Issue 7.0 RUN (LED 1) = The CPU is operating (green) LED 2, and 3 = Alarms (red) LED 4 = Flash access indication (red) LED 5 = The USB memory connection status (red) (LED off when no USB memory installed) Refer to Program 90-10: System Alarm Setup for details on assigning alarm LEDs.
  • Page 174: Connectors

    Issue 7.0 UNIVERGE SV8100 Table 4-7 CD-CP00 LED Indications (Continued) LED Indication Status RUN (LED1) LED2 LED3 LED4 LED5 Blinking On Steady When Flash memory booting error USB Memory is Installing Blinking On Steady When Flash memory data error USB Memory is...
  • Page 175 UNIVERGE SV8100 Issue 7.0 Table 4-9 CD-LTA RJ45 Cable Connector Pin-Outs USB Cable Connector – CN5 (Type A, Female) (USB 1.1/2.0 Standard) Pin No. Signal 1 2 3 4 Ethernet Cable Connector – CN7 (RJ-45) (10Base-T/100Base-TX Port) Pin No. Connection –...
  • Page 176 Issue 7.0 UNIVERGE SV8100 Table 4-9 CD-LTA RJ45 Cable Connector Pin-Outs (Continued) Pin No. Connection EXCNT2 EXCNT1 EXCNT1 EXCNT2 4 - 26 Installing the SV8100 Blades...
  • Page 177: Pz-Me50 (Memory Expansion Daughter Board)

    UNIVERGE SV8100 Issue 7.0 PZ-ME50 (Memory Expansion Daughter Board) Figure 4-6 PZ-ME50 Daughter Board 3.2.1 Description The Memory Expansion daughter board (PZ-ME50) provides additional memory for the system for use with license control, expanded system networking, InMail e-mail notification, and software updates.
  • Page 178: Installation

    Issue 7.0 UNIVERGE SV8100 Table 4-11 PZ-ME50 Capacities provides the memory capacities for the PZ-ME50 blades. Table 4-11 PZ-ME50 Capacities Memory Description Equipped Memory Capacity SDRAM 128 MB 256 MB / 16 bit x 4 pcs Flash 32 MB 256 MB / 16 bit x 1 pc...
  • Page 179 UNIVERGE SV8100 Issue 7.0 For installation on the CD-CP00 blade refer to Figure 4-4 CD-CP00 Blade with Daughter Boards Installed on page 4-17. This daughter board does not have any switches which need to be set and does not require any hardware setting.
  • Page 180: Pz-Vm21 (Voice Mail Daughter Board Inc. V34 Modem)

    Issue 7.0 UNIVERGE SV8100 PZ-VM21 (Voice Mail Daughter Board inc. V34 modem) Figure 4-7 PZ-VM21 Daughter Board 3.3.1 Description The SV8100 voice mail is a fully integrated, “in-skin” voice mail with Automated Attendant. In addition to the voice mail function, the daughter board provides Voice Response System (VRS) and an optional modem ability for remote maintenance functions.
  • Page 181: Installation

    UNIVERGE SV8100 Issue 7.0 3.3.2 Installation To install a PZ-VM21 on the CD-CP00: Do not remove or install the CD-CP00 with the power on. Included with the PZ-VM21 are four plastic spacers. Install the plastic spacers onto the PZ-VM21. Make sure to attach the spacers so that they extend out on the side of the daughter board which has the CN1 connector.
  • Page 182 Issue 7.0 UNIVERGE SV8100 Figure 4-8 Installing the PZ-VM21 One PZ-VM21 daughter board providing InMail can be installed per system. Refer to the Univerge UNIVERGE SV8100 System InMail System Guide for complete set-up information. 4 - 32 Installing the SV8100 Blades...
  • Page 183: Switch Settings

    UNIVERGE SV8100 Issue 7.0 3.3.3 Switch Settings This daughter board does not have any switch that needs to be set and does not require any hardware setting. 3.3.4 Remote PC Programming access The VM21 card provides a V34 modem for PC Programming connection.
  • Page 184 Issue 7.0 UNIVERGE SV8100 Boards) Figure 4-9 PZ-32IPLA VoIPDB-32 Daughter Board Figure 4-10 PZ-64IPLA VoIPDB-64 Blade 4 - 34 Installing the SV8100 Blades...
  • Page 185: Description

    UNIVERGE SV8100 Issue 7.0 Figure 4-11 PZ-128IPLA VoIPDB-128 Blade 3.4.1 Description The PZ-32IPLA/PZ-64IPLA/PZ-128IPLA daughter boards are used for converting the RTP (Real Time Transfer Protocol) packets via the IP network and PCM highway. The daughter board is installed on the CD-CP00.
  • Page 186: Installation

    3-41 for more details. Connect the IPLA Daughter board to the CD-RTB or to an external switching hub using an ethernet cable. Refer to the Univerge SV8100 Programming Manual for detailed programming instructions. 3.4.3 Switch Settings These daughter boards do not have any switches that need to be set and do not require any hardware setting.
  • Page 187: Led Indications

    UNIVERGE SV8100 Issue 7.0 3.4.4 LED Indications LED indications for the PZ-32IPLA, PZ-64IPLA and PZ-128IPLA Daughter Boards are indicated in Table 4-17 IPLB Daughter Board Indications. Each LED is listed with its associated function and LED and Operational status. Refer to...
  • Page 188: Connectors

    Issue 7.0 UNIVERGE SV8100 3.4.5 Connectors Figure 4-14 VoIP Connections shows a typical connection layout. Figure 4-15 Connecting a IPLA Daughter Board to a Network/PC illustrates how to connect a VoIP Daughter Board to a Network or Figure 4-12 VoIP Connections...
  • Page 189: Pz-32Iplb/Pz-64Iplb/Pz-128Iplb (Voice Over Ip Daughter Boards)

    UNIVERGE SV8100 Issue 7.0 PZ-32IPLB/PZ-64IPLB/PZ-128IPLB (Voice over IP Daughter Boards) Figure 4-13 IPLB Daughter Blade 3.5.1 Description The current PZ-32/64/128 IPLA daughter board requires a maximum of eight DSP IP addresses. The new PZ-32/64/128 IPLB requires only one DSP IP address for all three daughter board types.
  • Page 190: Installation

    3-41 for more details. Connect the IPLB Daughter board to the CD-RTB or to an external switching hub using an ethernet cable. Refer to the Univerge SV8100 Programming Manual for detailed programming instructions. 3.5.3 Switch Settings These daughter boards do not have any switches that need to be set and do not require any hardware setting.
  • Page 191 UNIVERGE SV8100 Issue 7.0 The following table shows the LED indication when transmitting or receiving data on CN1. Table 4-18 VOIPDB LED CN1 Transmit/Receive Data Indications Link Up Auto Negotiation Mode Force Mode 100Mbps 10Mbps 100Mbps 10Mbps 1000 1000 M bps...
  • Page 192: Connectors

    Issue 7.0 UNIVERGE SV8100 3.5.5 Connectors Figure 4-14 VoIP Connections shows a typical connection layout. Figure 4-15 Connecting a IPLA Daughter Board to a Network/PC illustrates how to connect a VoIP Daughter Board to a Network or Figure 4-14 VoIP Connections...
  • Page 193 UNIVERGE SV8100 Issue 7.0 Figure 4-15 Connecting a IPLA Daughter Board to a Network/PC System Hardware Manual 4 - 43...
  • Page 194: Station Blades

    Issue 7.0 UNIVERGE SV8100 TATION LADES ECTION CD-8DLCA/CD-16DLCA (Digital Station Interface) Figure 4-16 CD-8DLCA Blade 4 - 44 Installing the SV8100 Blades...
  • Page 195: Description

    UNIVERGE SV8100 Issue 7.0 Figure 4-17 CD-16DLCA Blade 4.1.1 Description These blades provide: 8 (CD-8DLCA) OR 16 (CD-16DLCA) digital extension circuits (used for digital telephones, DSS consoles, SLT(1)-U( ) ADP, PGD(2)-U10 ADP adapters) These ports provide -48V feeding. Two blade status LEDs – One Live LED, One Busy/Idle LED...
  • Page 196: Installation

    Issue 7.0 UNIVERGE SV8100 Table 4-19 CD-8DLCA/CD-16DLCA Maximum Upgrade Capacities provides the maximum capacities for the ESIU blades when they are upgraded. Table 4-19 CD-8DLCA/CD-16DLCA Maximum Upgrade Capacities 19” 19” Chassis 19” Chassis Networked ESIU Chassis without CPU Chassis with CPU...
  • Page 197: Connectors

    UNIVERGE SV8100 Issue 7.0 Table 4-20 CD-8DLCA/CD-16DLCA LED Indications (Continued) LED Indication Operation Status Remarks Live LED Busy LED (Green) (Red) A Channel is busy (use – Flash Normal another from CH1 ~ CHx). (100ms) Operation All channels are idle.
  • Page 198 Issue 7.0 UNIVERGE SV8100 Table 4-21 CD-8DLCA/CD-16DLCA/ RJ-61 Cable Connector Pin-Outs RJ-61 Cable Connector CD-8DLCA – CN101 (ports 1~4), CN201 (ports 5~8) CD-16DLCA – CN101 (ports 1~4), CN201 (ports 5~8), CN301 (ports 9~12), CN401 (ports 13~16) Pin No. Connection T4 (Tip for port 4)
  • Page 199: Pz-8Dlcb (Digital Station Daughter Board)

    UNIVERGE SV8100 Issue 7.0 PZ-8DLCB (Digital Station Daughter Board) Figure 4-18 PZ-8DLCB Blade 4.2.1 Description The PZ-8DLCB daughter board provides eight digital extensions. This daughter board is installed on the CD-8DLCA and expands the port capacity for the combined blades to 16.
  • Page 200: Installation

    Issue 7.0 UNIVERGE SV8100 4.2.2 Installation The PZ-8DLCB is installed on the CD-8DLCA. To install: Connect the PZ-8DLCB to the CN2 connector on the CD-8DLCA blade. Refer to Figure 4-16 CD-8DLCA Blade on page 4-44 for the location of the connectors on the blade.
  • Page 201 UNIVERGE SV8100 Issue 7.0 Table 4-24 PZ-8DLCB CN401 Connection RJ-61 Cable Connector CN401 (ports 13~16) Pin No. Connection (T4) Tip for port 16 (T3) Tip for port 15 (T2) Tip for port 14 (R1) Ring for port 13 (T1) Tip for port 13...
  • Page 202: Cd-4Lca/ Cd-8Lca (4-Port/8-Port Single Line Interface)

    Issue 7.0 UNIVERGE SV8100 CD-4LCA/ CD-8LCA (4-Port/8-Port Single Line Interface) Figure 4-19 CD-4LCA Blade 4 - 52 Installing the SV8100 Blades...
  • Page 203: Description

    UNIVERGE SV8100 Issue 7.0 Figure 4-20 CD-8LCA Blade 4.3.1 Description The 4/8SLIU blade provides four (4SLIU) analog extension ports or eight (8SLIU) analog extension ports (used for on-premise analog telephones, fax machines, and analog modems). System Hardware Manual 4 - 53...
  • Page 204 Issue 7.0 UNIVERGE SV8100 The 4SLIU and 8SLIU are not rated for OPX use. A 4DIOPU blade should be used instead (it supports the analog DID and single line telephone interface functions, such as Off-Premise Extensions). One extension status LED...
  • Page 205: Installation

    UNIVERGE SV8100 Issue 7.0 4.3.2 Installation When connecting a fax machine or analog modem, make sure to set Program 15-03-03 to 1 (special terminal) to avoid communication problems. The SLIU and SLIDB are categorized as TNV2. With this designation, off-premise wiring is not acceptable.
  • Page 206 Issue 7.0 UNIVERGE SV8100 Table 4-26 CD-4LCA/CD-8LCA LED Indications (Continued) LED Indication Operation Status Remarks Live LED Busy LED (Green) (Red) A Channel is busy (use – Unit Busy another from CH1 ~ CHx). All channels are idle. – Flash (100ms Downloading firmware.
  • Page 207: Connectors

    UNIVERGE SV8100 Issue 7.0 4.3.4 Connectors Table 4-27 CD-4LCA/CD-8LCA RJ-61 Cable Connector Pin-Outs show the pin-outs for the RJ-61 connector. Refer to Figure 4-19 CD-4LCA Blade on page 4-52 Figure 4-20 CD-8LCA Blade on page 4-53 for illustrations showing the location of the connectors and...
  • Page 208: Pz-4Lca/Pz-8Lce (4-Port/8-Port Sli Daughter Boards)

    Issue 7.0 UNIVERGE SV8100 PZ-4LCA/PZ-8LCE (4-Port/8-Port SLI Daughter Boards) Figure 4-21 Installing the PZ-4LCA Daughter Board 4 - 58 Installing the SV8100 Blades...
  • Page 209 UNIVERGE SV8100 Issue 7.0 Figure 4-22 Installing the PZ-8LCE Daughter Board System Hardware Manual 4 - 59...
  • Page 210: Description

    Issue 7.0 UNIVERGE SV8100 4.4.1 Description The PZ-4LCA and PZ-8LCE daughter boards are mounted on the CD-4LCA/CD-8LCA. These boards provide: 4-Port Single Line and 8-Port Single Line analog extension ports (used for on-premise analog telephones, fax machines, and analog modems).
  • Page 211: Installation

    UNIVERGE SV8100 Issue 7.0 4.4.2 Installation When connecting a fax machine or analog modem, make sure to set Program 15-03-03 to 1 (special terminal) to avoid communication problems. The SLIU and SLIDB are categorized as TNV2. With this designation, off-premise wiring is not acceptable.
  • Page 212: Connectors

    Issue 7.0 UNIVERGE SV8100 4.4.3 Connectors Table 4-29 PZ-4LCA/PZ-8LCE/ RJ-61 Cable Connector Pin-Outs show the pin-outs for the RJ-61 connector. Refer to Figure 4-21 Installing the PZ-4LCA Daughter Board on page 4-58 Figure 4-22 Installing the PZ-8LCE Daughter Board on page 4-59 illustrations showing the location of the connectors on the SLIDB blades.
  • Page 213: Installation

    UNIVERGE SV8100 Issue 7.0 DC Voltage (On hook) (-28Vdc) Feeding Polarity Reverse Ability Ring Generator (75Vrms, 16Hz/20Hz/25Hz selectable by CM82-04-02) Caller ID Sending Ability Message Wait Lamping Ability (110V DC) Cable length = 600ohms (including the SLT). Approximately 1Km The CD-16LCAH consumes sixteen ports ranging between ports 001~256.
  • Page 214 Issue 7.0 UNIVERGE SV8100 Table 4-31 CD-16LCAH LED Indications LED Indication Operation Status Remarks Live LED Busy LED (Green) (Red) System Initializing – When you exceed the system capacity. Flash (1s) The assignment of the unit is refused. When the main software version is not matched.
  • Page 215: Connectors

    UNIVERGE SV8100 Issue 7.0 4.5.4 Connectors Table 4-32 CD-16LCAH RJ-61 Cable Connector Pin-Outs show the pin-outs for the RJ-61 connector. Table 4-32 CD-16LCAH RJ-61 Cable Connector Pin-Outs RJ-61 Cable Connector 8SLIU – CN2 (ports 1~4) 8SLIU – CN2 (ports 1~4), CN3 (ports 5~8) Pin No.
  • Page 216: Cd-Lta (D Term /Slt Combination)

    Issue 7.0 UNIVERGE SV8100 term CD-LTA (D /SLT Combination) Figure 4-23 CD-LTA Blade 4.6.1 Description The Digital Station/SLT Combination blade provides eight Digital Station ports and two analog ports. This blade allows for either a PZ-4COTE analog trunk daughter board or PZ-2BRIA daughter board to be installed.
  • Page 217: Installation

    UNIVERGE SV8100 Issue 7.0 Eight Digital Station ports Two analog extension ports Two status LEDs Table 4-33 CD-LTA Maximum Upgrade Capacities provides the maximum capacities for the CD-LTA blades when they are upgraded. Table 4-33 CD-LTA Maximum Upgrade Capacities CCPU...
  • Page 218: Led Indications

    Issue 7.0 UNIVERGE SV8100 4.6.3 LED Indications LED indications for the CD-LTA are indicated in Table 4-34 CD-LTA Indications. Each LED is listed with its associated function and LED and Operational status. Refer to Figure 4-23 CD-LTA Blade on page 4-66 for the location of the LEDs on the blade.
  • Page 219: Connectors

    UNIVERGE SV8100 Issue 7.0 4.6.4 Connectors Table 4-35 CD-LTA RJ61 Cable Connector Pin-Outs on page 4-69 shows the pin-outs for the RJ-61 connector. Refer to Figure 4-23 CD-LTA Blade on page 4-66 for an illustration showing the location of the connectors on the CD-LTA blade.
  • Page 220: Cd-8Ltch ( D Term /Slt/Loop Start Analogue Trunk Combination)

    Issue 7.0 UNIVERGE SV8100 term CD-8LTCH (D /SLT/Loop Start Analogue Trunk Combination) 4.7.1 Description The Digital Station/SLT/Loop Start Analogue Trunk Combination blade provides eight Digital Station ports, two analog ports and four loop start analogue trunk ports. This blade displays the same characteristics as a CD-LTA blade fitted with a PZ-4COTE analogue trunk daughter board installed with the exception being that they cannot be seperated.
  • Page 221: Led Indications

    UNIVERGE SV8100 Issue 7.0 4.7.3 LED Indications LED indications for the CD-8LTCH are indicated in Table 4-37 CD- 8LTCH LED Indications. Each LED is listed with its associated function and LED and Operational status. Table 4-37 CD-8LTCH LED Indications LED Indication...
  • Page 222: Connectors

    Issue 7.0 UNIVERGE SV8100 4.7.4 Connectors Table 4-38 CD-8LTCH RJ61 Cable Connector Pin-Outs on page 4-72 shows the pin-outs for the RJ-61 connector. Table 4-38 CD-8LTCH RJ61 Cable Connector Pin-Outs RJ61 Cable Connector Digital: CN1 (ports 1~4) Digital: CN2 (ports 5~8) Pin No.
  • Page 223 UNIVERGE SV8100 Issue 7.0 Table 4-38 CD-8LTCH RJ61 Cable Connector Pin-Outs (Continued) Pin No. Connection Circuit 4 – Tip Circuit 3 – Tip Circuit 2 – Tip Circuit 1 – Ring Circuit 1 – Tip Circuit 2 – Ring Circuit 3 – Ring Circuit 4 –...
  • Page 224: Trunk Blades

    Issue 7.0 UNIVERGE SV8100 RUNK LADES ECTION CD-4COTA (4 Loop Start Interface) Figure 4-24 CD-4COTA Blade 5.1.1 Description The COIU blade provides: CD-4COTA: Four analog loop start trunk circuits One trunk status LED 4 - 74 Installing the SV8100 Blades...
  • Page 225 UNIVERGE SV8100 Issue 7.0 One Blade status LED Four Caller ID Circuits Two Power Failure Transfer Circuits Connection for COIDB Daughter Board The 4COIU blade consumes four trunk ports ranging between ports 001~200. The CN2 connector provides connection to four analog trunk ports, which are polarity sensitive (tip-to-tip, ring-to-ring).
  • Page 226: Installation

    Issue 7.0 UNIVERGE SV8100 5.1.2 Installation Install the COIU blade into an available slot in the chassis. (Refer to Figure 4-24 CD-4COTA Blade on page 4-74 for a layout of the blade.) If the PZ-4COTE is to be used, install this prior to inserting the CD-4COTA blade into the chassis.
  • Page 227: Connectors

    UNIVERGE SV8100 Issue 7.0 5.1.4 Connectors Table 4-41 CD-4COTA RJ-61 Cable Connector Pin-Outs on page 4-77 shows the pin-outs for the RJ-61 connector. Refer to Figure 4-24 CD-4COTA Blade on page 4-74 for an illustration showing the location of the connectors on the 4COIU blades.
  • Page 228: Pz-4Cote (4 Loop Start Interface Daughter Board)

    Issue 7.0 UNIVERGE SV8100 PZ-4COTE (4 Loop Start Interface Daughter Board) Figure 4-25 Installing the PZ-4COTE Daughter Board 5.2.1 Description The PZ-4COTE blade provides: PZ-4COTE: Four analog loop start trunk circuits Four Caller ID Circuits Connector for COIU Blade Connector for CD-LTA...
  • Page 229 UNIVERGE SV8100 Issue 7.0 The PZ-4COTE consumes four trunk ports ranging between ports 001~200. The CN2 connector provides connection to four analog trunk ports, which are polarity sensitive (tip-to-tip, ring-to-ring). The power failure circuits (CN3), however, are not polarity sensitive.
  • Page 230: Installation

    Issue 7.0 UNIVERGE SV8100 5.2.2 Installation To install the PZ-4COTE Four plastic spacers are included with the COIDB. Install the plastic spacers on the CD-4COTA or CD-LTA blade. Make sure to attach the spacers so that they extend out on the side of the daughter board which has the CN1 connector.
  • Page 231: Cd-8Cotah (8 Port Analogue Trunk Card)

    UNIVERGE SV8100 Issue 7.0 Table 4-43 PZ-4COTE RJ-61 Cable Connector Pin-Outs (Continued) RJ-61 Cable Connector CN2, Trunks – Connecting to CD-LTB/CD-LTA Blade The CN2 connector is polarity sensitive (tip-to-tip, ring-to-ring). Pin No. Connection Circuit 4 – Tip Circuit 3 – Tip Circuit 2 –...
  • Page 232 Issue 7.0 UNIVERGE SV8100 The connectors provides connection to four analog trunk ports, which are polarity sensitive (tip-to-tip, ring-to-ring). The power failure circuits (CN3), however, are not polarity sensitive. The trunk ports are polarity sensitive. Be careful when wiring the trunks.
  • Page 233: Installation

    UNIVERGE SV8100 Issue 7.0 5.3.2 Installation Install the CD-8COTAH blade into an available slot in the chassis. 5.3.3 LED Indications LED indications for the CD-4COTA are listed in Table 4-45 CD- 8COTAH LED Indications. Each LED is listed with its associated function and LED and Operational status.
  • Page 234: Shows The Pin-Outs For The Rj-61 Connector

    Issue 7.0 UNIVERGE SV8100 4-84 shows the pin-outs for the RJ-61 connector. Table 4-46 CD-8COTAH RJ-61 Cable Connector Pin-Outs RJ-61 Cable Connector – CN2, Trunks The CN2 connector is polarity sensitive (tip-to-tip, ring-to-ring). Pin No. Connection Circuit 4 – Tip Circuit 3 –...
  • Page 235 UNIVERGE SV8100 Issue 7.0 Table 4-46 CD-8COTAH RJ-61 Cable Connector Pin-Outs (Continued) RJ-61 Cable Connector CN2, Trunks The CN2 connector is polarity sensitive (tip-to-tip, ring-to-ring). Pin No. Connection Circuit 8 – Tip Circuit 7 – Tip Circuit 6 – Tip Circuit 5 –...
  • Page 236: Cd-2Bria (2 Basic Rate Interface)

    Issue 7.0 UNIVERGE SV8100 CD-2BRIA (2 Basic Rate Interface) Figure 4-26 CD-2BRIA Blade 5.4.1 Description This unit is an interface unit that accommodates an ISDN (Basic Rate) circuit. The BRI blade provides: Two (CD-2BRIA) 2-Channel Circuits (2B + D) configured as T-Bus...
  • Page 237: Installation

    UNIVERGE SV8100 Issue 7.0 64 Kb/s Clear B-Channel and 16 Kb/s D-Channel Two Status LEDs Connector for PZ-2BRIA These trunk circuits can be connected to either ISDN trunks or ISDN telephones, depending on the switch setting within system programming. All ISDN telephone circuits (#1-2 and #3-4 with the BRI daughter board) are supplied DC power from the system.
  • Page 238: Led Indications

    Issue 7.0 UNIVERGE SV8100 With normal operation, the status LED flashes fast. If trouble was found during the self diagnostics routine, the status LED flashes slow. Once connected, the PKG LED will not be indicated for the status of Layer 1 Link.
  • Page 239: Connectors

    UNIVERGE SV8100 Issue 7.0 5.4.4 Connectors Table 4-49 CD-2BRIA RJ-45 T-Bus Cable Connector Pin-Outs show the pin-outs for the RJ-45 cable connector for S-Bus and T-Bus connections. Refer to Figure 4-26 CD-2BRIA Blade on page 4-86 an illustration showing the location of the connectors on the CD-2BRIA blade.
  • Page 240 Issue 7.0 UNIVERGE SV8100 The switches 6 and 7 define if the terminators are active. These should be set to ON, if the bus has no termination. If the bus is already terminated they may be set to OFF. Every ISDN-Bus must be terminated with a set of 100Ohm resistors at its ends.
  • Page 241: Pz-2Bria (2 Basic Rate Interface Daughter Board)

    UNIVERGE SV8100 Issue 7.0 PZ-2BRIA (2 Basic Rate Interface Daughter Board) Figure 4-27 Installing the PZ-2BRIA Daughter Board System Hardware Manual 4 - 91...
  • Page 242: Description

    Issue 7.0 UNIVERGE SV8100 5.5.1 Description This daughter board provides two BRI circuits and is installed on the CD-2BRIA blade. This board provides: Two (CD-2BRIA) 2-Channel Circuits (2B + D) configured as T-Bus or S-Bus 64 Kb/s Clear B-Channel and 16 Kb/s D-Channel...
  • Page 243: Connectors

    UNIVERGE SV8100 Issue 7.0 Before proceeding to Step 3, wait to verify that the STATUS LED starts to flash. With normal operation, the status LED flashes fast. If trouble was found during the self diagnostics routine, the status LED flashes slow.
  • Page 244: Termination Switch Settings

    Issue 7.0 UNIVERGE SV8100 Table 4-51 PZ-2BRIA RJ-45 T-Bus Cable Connector Pin-Outs RJ-45 Cable Connector – CN7, CN8 T-Bus connection Pin No. Connection — — — — 5.5.4 Termination Switch Settings When the card is installed it may be necessary to change the termination switch settings.
  • Page 245: Cd-4Diopb (Did/Opx Interface)

    UNIVERGE SV8100 Issue 7.0 CD-4DIOPB (DID/OPX Interface) Figure 4-28 CD-4DIOPB Blade 5.6.1 Description The CD-4DIOPB supports the analog DID and single line telephone interface functions (such as Off-Premise Extension). The function type is assigned in programming for each port. The circuit types, however, should be grouped together.
  • Page 246: Installation

    Issue 7.0 UNIVERGE SV8100 Four (4DIOPU) DID trunk circuits or four OPX circuits Two Blade status LEDs Table 4-52 CD-4DIOPB Maximum Upgrade Capacities provides the maximum capacities for the CD-4DIOPB blades when they are upgraded. Table 4-52 CD-4DIOPB Maximum Upgrade Capacities 19”...
  • Page 247: Connectors

    UNIVERGE SV8100 Issue 7.0 5.6.4 Connectors The CN2 connector provides connection to four analog DID trunk ports, which are polarity sensitive (tip-to-tip, ring-to-ring). The OPX circuits, however, are not polarity sensitive. The DIOPU requires one universal slot. (Refer to Figure 4-28 CD-4DIOPB Blade on page 4-95.) If Program 10-03-01 has OPX defined, note that the...
  • Page 248: Cd-Prta (Pri Interface)

    Issue 7.0 UNIVERGE SV8100 CD-PRTA (PRI Interface) Figure 4-29 CD-PRTA Blade (Front and Side View) 5.7.1 Description The CD-PRTA PRI blade provides an interface for ISDN Primary Rate Interface (PRI) applications. This blade has a single 30-channel 64Kb per second digital signal circuit configured for PRI. Each blade connects to the network via an NTI Network Termination.
  • Page 249: Installation

    UNIVERGE SV8100 Issue 7.0 Basic PRI Call Control (BCC) Display of incoming caller’s name and number (when allowed by the telco) Speech and 3.1 KHz audio When installed, CD-PRTA uses the first block of 32 consecutive trunk ports. For example, if a COIU blade is installed for trunks 1~8, the CD-PRTA automatically uses trunks 9~40.
  • Page 250 Issue 7.0 UNIVERGE SV8100 Layout for NT-1 Network on page 4-100 for a cabling diagram.) The CSU connects to the network through an 8-pin RJ-45/RJ48C connector. Use either the RJ48C plug-to-RJ48C plug, which ships with the CSU or an RJ-45/...
  • Page 251: Led Indications

    UNIVERGE SV8100 Issue 7.0 5.7.3 LED Indications LED indications for the CD-PRTA are listed in Table 4-56 CD-PRTA Indications. Each LED is listed with its associated function and LED and Operational status. Refer to Figure 4-31 CD-PRTA LED Indication Pattern of Layer 1 on T1 Unit on page 4-102 for LED pattern information.
  • Page 252 Issue 7.0 UNIVERGE SV8100 Figure 4-31 CD-PRTA LED Indication Pattern of Layer 1 on T1 Unit Table 4-57 ISDN LED Indications Alarm Details of the Alarm LED Indication Pattern Loss of Signal (Red alarm) Following an alarm blink (red, No Signam (Analogue...
  • Page 253: Connectors

    UNIVERGE SV8100 Issue 7.0 Table 4-57 ISDN LED Indications Alarm Details of the Alarm LED Indication Pattern Note: The order of priority is set up to alarm in the order LOS>AIS>OOF>RAI. 5.7.4 Connectors Table 4-58 CD-PRTA RJ-45 Cable Connector Pin-Outs shows the pin-outs for the RJ-45 connector.
  • Page 254 Issue 7.0 UNIVERGE SV8100 Table 4-59 CD-PRTA RJ48C Connector Pin-outs shows the pin-outs for the 8-pin RJ48C connector for the network and terminal interfaces. Table 4-59 CD-PRTA RJ48C Connector Pin-outs Network Interface Terminal Interface Pinout for the 8-Pin Pinout for the 8-Pin...
  • Page 255: Cd-4Odtb (4-Port Tie Line Interface Blade)

    UNIVERGE SV8100 Issue 7.0 CD-4ODTB (4-Port Tie Line Interface Blade) Figure 4-32 CD-4ODTB Blade 5.8.1 Description The CD-4ODTB Tie Line blade is an out band dial type analog tie line interface blade. This blade supports system connections to either 2- wire (four lead, tip/ring) or 4-wire (eight lead, tip/ring/tip 1/ring 1) E&M signalling tie lines (determined in Program 10-13 ).
  • Page 256: Installation

    Issue 7.0 UNIVERGE SV8100 Two Blade status LEDs Two straps and one switch per circuit to determine the circuit type Limitation depends on the connecting Router, Multiplexer or Exchange. If the UNIVERGE SV8100 is connected to another UNIVERGE SV8100 directly, there is up to 1,500 ohms loop resistance (including system).
  • Page 257: Led Indications

    UNIVERGE SV8100 Issue 7.0 5.8.3 LED Indications LED indications for the CD-4ODTB are listed in Table 4-61 CD-4ODTB LED Indications. Each LED is listed with its associated function and LED and Operational status. Refer to Figure 4-32 CD-4ODTB Blade on page 4-105 for the location of the LEDs on the blade.
  • Page 258 Issue 7.0 UNIVERGE SV8100 Table 4-62 CD-4ODTB RJ-61 Cable Connector Pin-Outs RJ-61 Cable Connector – 2-Wire E&M, CN1A~CN1D Pin No. Connection Description — Not Used Control signal to trunk — Not Used Voice signal both ways Voice signal both ways —...
  • Page 259: Connections

    UNIVERGE SV8100 Issue 7.0 5.8.5 Connections Figure 4-33 Voice Signal Connection for Type I And V on page 4-109 Figure 4-34 Control Signal Connection on page 4-110 show the signaling methods for circuit types. Figure 4-33 Voice Signal Connection for Type I And V...
  • Page 260 Issue 7.0 UNIVERGE SV8100 Figure 4-34 Control Signal Connection 4 - 110 Installing the SV8100 Blades...
  • Page 261: Optional Blades

    UNIVERGE SV8100 Issue 7.0 PTIONAL LADES ECTION CD-PVAA (Conference Bridge) (Future Enhancement) Figure 4-35 CD-PVAA Blade 6.1.1 Description The Packet Voice Application, CD-PVAA blade is an optional interface that supports Application Packages (Univerge Multimedia Conference Bridge, and Interactive Voice Response Application).
  • Page 262: Cd-Pvaa (Conference Bridge) (Future Enhancement)

    Issue 7.0 UNIVERGE SV8100 A digital signal processor/voice processing section handles the following functions: DTMF detection DTMF generation General tone detection Automatic Gain Control (AGC) Basic Support Package Each blade installed with the CNF or IVR package accounts for up to 16 Extension Ports of the Total Port capacity (One Conference or One IVR blade maximum).
  • Page 263: Connectors

    UNIVERGE SV8100 Issue 7.0 Fast Flash: Board is in sync with the chassis and operating normally Busy LED – Red On: Application problem CompactFlash Card Activity LED – Red CompactFlash Card Activity LED is controlled by the IDE controller and indicates read/write activity on the CompactFlash card.
  • Page 264: Cd-Rtb (4-Port )

    Issue 7.0 UNIVERGE SV8100 CD-RTB (4-Port ) Figure 4-36 CD-RTB Blade 6.2.1 Description The Router blade is a 4-port switching hub which complies with the ethernet specification for both 100Base-TX and 10Base-T. This blade is compatible in LAN applications using 10Mbps and 100Mbps.
  • Page 265 Maximum 100m Transmission Distance by CAT-5 Cable 2 Status LEDs The VoIPDB, which is required for IP telephones to communicate with non-VoIP UNIVERGE SV8100 telephones, and place or receive outside calls, must be connected to either an external switching hub or to the Router blade.
  • Page 266: Installation

    IP telephone and it allows for centralized power backup. 6.2.2 Installation To install the CD-RTB: Plug the CD-RTB blade into any universal slot. Refer to the Univerge SV8100 Programming Manual for required programming. 6.2.3 LED Indications LED indications for the CD-RTB are indicated in Table 4-64 CD-RTB Indications.
  • Page 267: Cd-Etia (Gigabit Poe Switch)

    UNIVERGE SV8100 Issue 7.0 CD-ETIA (Gigabit PoE Switch) Figure 4-37 CD-ETIA Blade 6.3.1 Description The CD-ETIA blade is a managed 8-port gigabit ethernet PoE switch. Ports 1 and 8 are the default uplink ports. All the user management and stacking is based on this setup. This blade provides:...
  • Page 268: Installation

    Issue 7.0 UNIVERGE SV8100 802.1p Priority Queuing Port Mirroring 802.3x Flow Control Independent VLAN Learning Support TCP/IP Networking Stack Multi-Unit Stacking (multiple blades in a system are managed from the same user interface) Dynamic PoE Control (allows setting the proper PoE classifications for...
  • Page 269: Cd-Cp00Ip Address Assignment

    UNIVERGE SV8100 Issue 7.0 6.3.2.2 CD-CP00IP Address Assignment The GSWU Main board will be provided with an IP address from the back plane CPU during the initialization sequence. The provision of an IP address from the back plane will identify the Main board. If during initialization, the IP address is set to 0 by the CPU, the blade is then determined to be an Add-on.
  • Page 270: Unmanaged Switch Functions

    The grouping of the three GSWU units to form a 20 port switch is restricted to reside in a single system location. The grouping is not allowed where the GSWU units are placed as part of the NetLink feature in the Univerge SV8100 system. 6.3.2.5...
  • Page 271 UNIVERGE SV8100 Issue 7.0 - - NOTES - - System Hardware Manual 4 - 121...
  • Page 272 Issue 7.0 UNIVERGE SV8100 4 - 122 Installing the SV8100 Blades...
  • Page 273: Chapter 5 Installing Dt300/Dt700 Series (Dtl/Itl) Digital And Ip

    Installing DT300/DT700 Series (DTL/ITL) Digital and IP Multiline Terminals ENERAL ESCRIPTION ECTION This chapter provides information about the DT300/DT700 Series digital Chapter and IP terminals in addition to the single line telephones, cordless telephones and wireless telephones. Table 5-1 Terminal Category Reference Chart DT300/DT700 Series Terminals Category Equipment ID...
  • Page 274 Issue 7.0 UNIVERGE SV8100 Table 5-1 Terminal Category Reference Chart DT300/DT700 Series Terminals Category Equipment ID Product Name (idea) Note Wireless C124 SIP DECT Handset G955 SIP DECT The DT300/DT700 Series offers a line up of modular telephones. This modular design allows the telephones to be upgraded and customized.
  • Page 275 UNIVERGE SV8100 Issue 7.0 Table 5-2 Terminal and Adapter Compatibility (Continued) Adapter Unit Terminal ADA-L APR-L ILPA PSA-L BCH-L BHA-L GBA-L ITL-320C-1 (BK) TEL –— –— –— Digital Terminals: DTL-2E-1 (BK) TEL –— –— –— –— –— –— –— DTL-6DE-1 (BK) TEL –—...
  • Page 276 Issue 7.0 UNIVERGE SV8100 Table 5-3 Terminal and Line Key/LCD Compatibility (Continued) Line Key/LCD Terminal 8 LK-L 8LKD(LD)-L 8LKI(LD)-L 12LK-L LCD (BL-L DCL-60 ITL-12DG-3 (BK) TEL –— –— –— ITL-12PA-1 (BK) TEL –— ITL-24D-1 (BK)/(WH) TEL –— –— ITL-32D-1 (BK)/(WH) TEL –—...
  • Page 277 UNIVERGE SV8100 Issue 7.0 Table 5-4 Terminal and Tenkey Kit Compatibility Tenkey Kit Terminal BS(F)-L BS(S)-L BS(ACD)-L BS(Braille)-L BS(Retro)-l IP Terminals: ITL-2E-1 (BK) TEL –— –— –— –— ITL-6DE-1 (BK) TEL –— –— –— –— ITL-8LDE-1 (BK) TEL –— –—...
  • Page 278 Issue 7.0 UNIVERGE SV8100 Table 5-5 Terminal and Optional Equipment Compatibility Equipment Terminal PSA-L PANEL-L WM-L IP Terminals: ITL-2E-1 (BK) TEL –— ITL-6DE-1 (BK) TEL –— ITL-8LDE-1 (BK) TEL –— ITL-8LD-1 (BK)/(WH) TEL ITL-12D-1 (BK)/(WH) TEL ITL-12CG-3 (BK) TEL ITL-12DG-3 (BK) TEL ITL-12PA-1 (BK) TEL –—...
  • Page 279: Dt300 Series Digital Multiline Terminals

    UNIVERGE SV8100 Issue 7.0 Table 5-5 Terminal and Optional Equipment Compatibility (Continued) Equipment Terminal PSA-L PANEL-L WM-L –— = Option Not Available = Optional Available * The WM-L is required if the ADA-L UNIT or APR-L UNIT are installed on the telephone.
  • Page 280 Issue 7.0 UNIVERGE SV8100 Figure 5-1 DTL-2E-1 TEL 5 - 8 Installing DT300/DT700 Series (DTL/ITL) Digital and IP Multiline Terminals...
  • Page 281: Dtl-6De-1 (Bk) Tel

    UNIVERGE SV8100 Issue 7.0 2.1.2 DTL-6DE-1 (BK) TEL This digital economy Multiline Terminal has six line keys with display and is available in black only. The terminal features: Non-modular design Four step adjustable base Half-duplex speaker phone Six line keys (Red, Green)
  • Page 282: Dtl-12Bt-1 (Bk) Tel

    Issue 7.0 UNIVERGE SV8100 Backlit 10-key dial pad for easy viewing Full-duplex handsfree operation Figure 5-3 DTL-8LD-1 TEL 2.1.4 DTL-12BT-1 (BK) TEL This digital value Multiline Terminal has 12 line keys and is available in black only. The terminal features:...
  • Page 283: Dtl-12D-1 (Bk) Tel/Dtl-12D-1 (Wh) Tel

    UNIVERGE SV8100 Issue 7.0 Figure 5-4 DTL-12BT-1 TEL 2.1.5 DTL-12D-1 (BK) TEL/DTL-12D-1 (WH) TEL This digital value Multiline Terminal has 12 line keys and is available in both black and white. The terminal features: Modular design Four step adjustable base...
  • Page 284: Dtl-12Pa-1 (Bk) Tel

    Issue 7.0 UNIVERGE SV8100 Figure 5-5 DTL-12D-1 TEL 2.1.6 DTL-12PA-1 (BK) TEL This digital value multiline terminal with Analog Power Failure adapter has 12 line keys and is available in black only. The terminal features: Modular design Four step adjustable base...
  • Page 285: Dtl-24D-1 (Bk) Tel/Dtl-24D-1 (Wh) Tel

    UNIVERGE SV8100 Issue 7.0 Figure 5-6 DTL-12PA-1 TEL 2.1.7 DTL-24D-1 (BK) TEL/DTL-24D-1 (WH) TEL This digital value Multiline Terminal has 24 line keys and is available in both black and white. The terminal features: Modular design Four step adjustable base...
  • Page 286: Dtl-32D-1 (Bk) Tel/Dtl-32D-1 (Wh) Tel

    Issue 7.0 UNIVERGE SV8100 Figure 5-7 DTL-24D-1 TEL 2.1.8 DTL-32D-1 (BK) TEL/DTL-32D-1 (WH) TEL This digital value Multiline Terminal has 32 line keys (24 line keys plus eight line key LK Unit) and is available in both black and white.
  • Page 287 UNIVERGE SV8100 Issue 7.0 Figure 5-8 DTL-32D-1 TEL System Hardware Manual 5 - 15...
  • Page 288: Dt700 Series Ip Multiline Terminals

    Issue 7.0 UNIVERGE SV8100 DT700 S IP M ERIES ULTILINE ERMINALS ECTION The DT700 Series offers a new exciting line up of IP telephones. These telephones (except economy), have a modular design that allows the telephones to be upgraded and customized. Optional LCD panels, dial pads, feature key kits, handset cradles, face plates and colored side panels can easily be snapped on and off to upgrade and customize as the customer desires.
  • Page 289: Itl-6De-1 (Bk) Tel

    UNIVERGE SV8100 Issue 7.0 3.1.2 ITL-6DE-1 (BK) TEL This IP economy Multiline Terminal has six line keys with display and is available in black only. The terminal features: Non-modular design Four step adjustable base Remote login and maintenance Full-duplex speaker phone...
  • Page 290: Itl-8Ld-1 (Bk) Tel/Itl-8Ld-1 (Wh) Tel

    Issue 7.0 UNIVERGE SV8100 224 x 96 dot matrix gray scale backlit LCD IEEE 802.3af compliant XML open interface (limited) 10 Base-T/100 Base-TX network interface Wide Band Handset Figure 5-11 ITL-8LDE-1 TEL 3.1.4 ITL-8LD-1 (BK) TEL/ITL-8LD-1 (WH) TEL This IP value Multiline Terminal has eight line keys with display and is available in both black and white.
  • Page 291: Itl-12D-1 (Bk) Tel/Itl-12D-1 (Wh) Tel

    UNIVERGE SV8100 Issue 7.0 Backlit LCD Figure 5-12 ITL-8LD-1 TEL 3.1.5 ITL-12D-1 (BK) TEL/ITL-12D-1 (WH) TEL This IP value Multiline Terminal has 12 line keys and is available in both black and white. The terminal features: Modular design Four step adjustable base...
  • Page 292: Itl-12Cg-3 (Bk) Tel

    Issue 7.0 UNIVERGE SV8100 Backlit LCD Figure 5-13 ITL-12D-1 TEL 3.1.6 ITL-12CG-3 (BK) TEL This IP value multiline terminal has 12 line keys and is available in black only. The terminal features: USB Connection (USB 2.0, 5V/500mA supply) Modular design...
  • Page 293: Itl-12Dg-3 (Bk) Tel

    UNIVERGE SV8100 Issue 7.0 Figure 5-14 ITL-12CG-3 TEL 3.1.7 ITL-12DG-3 (BK) TEL This IP value multiline terminal has 12 line keys and is available in black only. The terminal features: USB Connection (USB 2.0, 5V/500mA supply) Modular design Four-step adjustable base...
  • Page 294: Itl-12Pa-1 (Bk) Tel

    Issue 7.0 UNIVERGE SV8100 10 Base-T/100 Base-TX/1000 BASE-T network interface Figure 5-15 ITL-12DG-3 TEL 3.1.8 ITL-12PA-1 (BK) TEL This IP value Multiline Terminal with Analog Power Failure adapter has 12 line keys and is available in black only. The terminal features:...
  • Page 295: Itl-24D-1 (Bk) Tel/Itl-24D-1 (Wh) Tel

    UNIVERGE SV8100 Issue 7.0 Backlit LCD PSA Adapter for Power Failure Figure 5-16 ITL-12PA-1 TEL 3.1.9 ITL-24D-1 (BK) TEL/ITL-24D-1 (WH) TEL This IP value Multiline Terminal has 24 line keys and is available in both black and white. The terminal features:...
  • Page 296: Itl-32D-1 (Bk) Tel/Itl-32D-1 (Wh) Tel

    Issue 7.0 UNIVERGE SV8100 Figure 5-17 ITL-24D-1 TEL 3.1.10 ITL-32D-1 (BK) TEL/ITL-32D-1 (WH) TEL This IP value Multiline Terminal has 32 line keys (24 line keys plus an eight line key LK Unit) and is available in both black and white. The...
  • Page 297: Itl-320C-1 (Bk) Tel

    UNIVERGE SV8100 Issue 7.0 Figure 5-18 ITL-32D-1 TEL 3.1.11 ITL-320C-1 (BK) TEL This IP Multiline Terminal features a large color touch panel LCD and is available in black only. The terminal features: Modular design Four step adjustable base Full-duplex speaker phone...
  • Page 298 Issue 7.0 UNIVERGE SV8100 Figure 5-19 ITL-320C-1 TEL 5 - 26 Installing DT300/DT700 Series (DTL/ITL) Digital and IP Multiline Terminals...
  • Page 299: Install Multiline Terminals

    UNIVERGE SV8100 Issue 7.0 NSTALL ULTILINE ERMINALS ECTION Connecting the DT300 Series Multiline Terminal to the System This instruction applies to all DT300 Series Multiline Terminals. Plug the telephone cord into the modular jack on the bottom side of the Multiline Terminal.
  • Page 300: Applying Power To The Dt700 Multiline Terminals

    Issue 7.0 UNIVERGE SV8100 Lead the Line and Handset cables through the applicable grooves. Groove for Line and Handset Cables Figure 5-21 Leading Line Cords on a Multiline Terminal Applying Power to the DT700 Multiline Terminals The DT700 terminals support two different methods to power the terminal:...
  • Page 301: Connecting The Ip Multiline Terminal To The Network And Pc

    UNIVERGE SV8100 Issue 7.0 Connecting the IP Multiline Terminal to the Network and PC These instructions for connecting an IP Multiline Terminal to the Network and PC apply to DT700 Multiline Terminals. Refer to Figure 5-22 IP Terminal Connector Locations.
  • Page 302: Adjusting The Lcd On The Multiline Terminal

    Issue 7.0 UNIVERGE SV8100 Figure 5-23 Typical Network IP Connection Adjusting the LCD on the Multiline Terminal DT300/DT700 Series display Multiline Terminals have an adjustable Liquid Crystal Display (LCD). The LCD can be adjusted by pulling up or pushing down as desired.
  • Page 303: Installing Line Key Kit (12Lk-L Kit)

    UNIVERGE SV8100 Issue 7.0 Installing Line Key Kit (12LK-L KIT The 12LK-L KIT Provides twelve additional buttons to ITL or DTL multiline terminals. The 12LK-L KIT kit: Mounts directly to top side of terminal Supports Red and Green LED colors Figure 5-25 12LK-L Kit 4.5.1...
  • Page 304 Issue 7.0 UNIVERGE SV8100 Line Key Panel Figure 5-26 Removing the Line Key Panel Lift and remove the DESI sheet. DESI Sheet Figure 5-27 Removing the DESI Sheet Press the right end of the Line Key placeholder and lift to...
  • Page 305 UNIVERGE SV8100 Issue 7.0 Press here then Lift Figure 5-28 Removing the Line Key Placeholder Install the 12LK-L KIT and press down until click is heard. 12LK-L KIT Figure 5-29 Installing the 12LK-L KIT System Hardware Manual 5 - 33...
  • Page 306 Issue 7.0 UNIVERGE SV8100 If desired, print and install the new DESI sheet. Figure 5-30 Installing the DESI Sheet Install the supplied Line Key Panel (refer to Figure 5-31 Installing the Line Key Panel). Line Key Panel Figure 5-31 Installing the Line Key Panel Install the side panel.
  • Page 307: Configuring The Digital Telephone For The Correct Number Of Line Keys

    UNIVERGE SV8100 Issue 7.0 4.5.2 Configuring the Digital Telephone for the Correct Number of Line Keys With the telephone not plugged in and the handset on-hook, press the 4 and 6 buttons on the numbered keypad and connect the telephone cable.
  • Page 308 Issue 7.0 UNIVERGE SV8100 Press Soft Key 2 for Key Kit Type. Select the type of keypad kit being used by pressing the Up/ Down key. Table 5-7 Keypad Kit Type Keypad Kit Entry Description Kit1 Type A – Japan with cursor key Kit2 Type A –...
  • Page 309: Installing The Directory Card On The Multiline Terminal

    UNIVERGE SV8100 Issue 7.0 Continue pressing Soft Key 4 to exit (Exit-Exit-Save). The terminal will reset automatically. Installing the Directory Card on the Multiline Terminal A directory card can be attached to DT300/DT700 Series Multiline Terminals. The directory card can be used to record often dialed numbers or other important information.
  • Page 310: Installing A Numbered Keypad On The Multiline Terminal

    IPK II and IPS terminals. Standard Numbered Keypad The standard keypad (in black or white), is commonly delivered with the UNIVERGE SV8100 terminal (refer to Figure 5-34 Standard Numbered Keypad on page 5-39).
  • Page 311 UNIVERGE SV8100 Issue 7.0 Figure 5-34 Standard Numbered Keypad BS (Retro)-L KIT The optional Retro keypad (in black or white), is compatible with the term Series i telephone, allowing the terminal to be used with the IPK II, IPC 500 and IPS multiline terminals.
  • Page 312: Installing The Numbered Keypad On A Multiline Terminal

    Issue 7.0 UNIVERGE SV8100 4.7.1 Installing the Numbered Keypad on a Multiline Terminal To prevent possible damage to the Numbered Keypad or the DTL/ITL multiline terminal during installation or removal, disconnect the line cord/ LAN cable and the AC/DC adapter from the DTL/ ITL multiline terminal.
  • Page 313 UNIVERGE SV8100 Issue 7.0 Slide the replacement numbered keypad into the grooves located on the inside of the telephone, then press down on the keypad to snap it into place. See Figure 5-38 Install New Numbered Keypad into DT300/DT700 Series Terminal.
  • Page 314: Configuring The Digital Telephone For The Numbered Keypad

    Issue 7.0 UNIVERGE SV8100 4.7.2 Configuring the Digital Telephone for the Numbered Keypad With the telephone not plugged in and the handset on-hook, press the 4 and 6 buttons on the numbered keypad and connect the telephone cable. This places the telephone into Service Class R/W mode. The MW LED should be lit.
  • Page 315 UNIVERGE SV8100 Issue 7.0 At the Login screen, enter the user name (default = ADMIN) and password (default = 6633222) and press the OK Soft Key. Press Soft Key 3 for Maintenance Setting. Press Soft Key 4 for Adjust. Press Soft Key 2 for Key Kit Type.
  • Page 316: Adjusting The Height On The Multiline Terminal

    Issue 7.0 UNIVERGE SV8100 Table 5-11 Line Key Kit Type (Continued) Line Key Kit Entry Description Kit6 Value 6-Button Kit2 Value 2-Button Kit0 IP-CTS Press Soft Key 4 for OK to complete. Continue pressing Soft Key 4 to exit (Exit-Exit-Save). The terminal will reset automatically.
  • Page 317: Removing Or Installing The Tilt Legs On The Multiline Terminal

    UNIVERGE SV8100 Issue 7.0 Removing or Installing the Tilt Legs on the Multiline Terminal The Tilt Legs can be removed or installed on the DT300/DT700 Series multiline terminal. 4.9.1 Remove Tilt Legs Place the telephone on a flat surface (button side down).
  • Page 318: Install Tilt Legs

    Issue 7.0 UNIVERGE SV8100 Lift and remove the Tilt Legs. 4.9.2 Install Tilt Legs Place the telephone on a flat surface (button side down). Lay the adjustable Tilt legs on top of the telephone. See Figure 5-43 Attach Tilt Legs to DT300/DT700 Series Terminal.
  • Page 319 UNIVERGE SV8100 Issue 7.0 Figure 5-44 Connecting the Tilt Legs Snap legs together and adjust to desired height. See Figure 5-45 Adjust Height of DT300/DT700 Series Terminal). Figure 5-45 Adjust Height of DT300/DT700 Series Terminal System Hardware Manual 5 - 47...
  • Page 320: Wall Mounting The Multiline Terminal

    Issue 7.0 UNIVERGE SV8100 4.10 Wall Mounting the Multiline Terminal You can wall mount a DT300/DT700 Series connection Multiline Terminal using the base cover or an optional wall mount unit. A wall mount unit must be used if adapters are installed on the Multiline Terminal.
  • Page 321: Wall Mounting The Multiline Terminal

    UNIVERGE SV8100 Issue 7.0 4.10.1.2 Wall Mounting the Multiline Terminal Plug line cord in the wall receptacle. Leave about eight inches of cord and bundle the rest as shown in Figure 5-48 Bundling the Line Cord. Figure 5-48 Bundling the Line Cord Ensure the Tilt Legs are in the flat (unused position).
  • Page 322: Removing The Multiline Terminal From The Wall Mounted Base Plate

    Issue 7.0 UNIVERGE SV8100 Figure 5-50 Mount Multiline Terminal Wall on Wall Plate Push spare line cord behind the Multiline Terminal. 4.10.1.3 Removing the Multiline Terminal from the Wall Mounted Base Plate. To remove the Multiline Terminal, push up on the telephone until it comes loose.
  • Page 323: Wall Mounting The Base On A Switch Box

    UNIVERGE SV8100 Issue 7.0 4.10.1.4 Wall Mounting the Base on a Switch Box Locate the screw holes on the base and hang the cover over the screws on the switch box as illustrated in Figure 5-52 Wall Mounting Base on Switch Box.
  • Page 324: Dt300/Dt700 Series Terminal Options

    Issue 7.0 UNIVERGE SV8100 ULTILINE ERMINALS PTIONAL QUIPMENT ECTION DT300/DT700 Series Terminal Options The following chart provides a quick overview of the options available with the DT300/DT700 Series telephones. Table 5-12 Connectivity of Options IP Terminals Digital Terminals Value Value...
  • Page 325: Dt300/Dt700 Series Optional Terminal Equipment

    UNIVERGE SV8100 Issue 7.0 DT300/DT700 Series Optional Terminal Equipment 5.2.1 8LK-L (BK) UNIT/8LK-L (WH) UNIT Provides eight additional line keys to ITL or DTL terminals (except Economy). The unit features: Mounts directly to right side of terminal Supports Red and Green LED colors Figure 5-54 8LK-L UNIT 5.2.1.1...
  • Page 326 Issue 7.0 UNIVERGE SV8100 Pry the side panel from the multiline terminal. Side Panel Figure 5-55 Remove Side Panel from Multiline Terminal Return the multiline terminal to the buttons side up position. Fit the projections on the side of the 8LK-L UNIT into the guide holes on the side of the multiline terminal.
  • Page 327: 8Lkd (Ld)-L (Bk) Unit/8Lkd (Ld)-L (Wh) Unit

    UNIVERGE SV8100 Issue 7.0 Open the small door covering the side option connectors by pulling the cover handle to the front. Telephone Side Option Connection Cable Connector Cover Figure 5-57 Install the 8LK-L UNIT Cable Connect the cable from the 8LK-L UNIT to the side...
  • Page 328: Installing The 8Lkd (Ld)-L Unit

    Issue 7.0 UNIVERGE SV8100 Figure 5-58 8LKD (LD)-L UNIT 5.2.2.1 Installing the 8LKD (LD)-L UNIT To prevent possible damage to the 8LKD (LD)-L UNIT or the DTL multiline terminal during installation or removal, disconnect the line cord/LAN cable and the AC/DC adapter from the DTL multiline terminal.
  • Page 329 UNIVERGE SV8100 Issue 7.0 Remove the screw (refer to Figure 5-59 Remove Side Panel from Multiline Terminal on page 5-56). Carefully, return the multiline terminal to the buttons side up position. Remove the soft keys and line key kit from the telephone.
  • Page 330 Issue 7.0 UNIVERGE SV8100 Guide Projection Guide (One Each Side) Figure 5-61 Ribbon Cable Installed Align the projections on the bottom of the 8LKD (LD)-L UNIT into the guide holes on top of the multiline terminal. Slide the 8LKD (LD)-L UNIT toward the keypad...
  • Page 331: 8Lki (Ld)-L (Bk) Unit/8Lki (Ld)-L (Wh) Unit

    UNIVERGE SV8100 Issue 7.0 Holding the LCD in place, turn the multiline terminal button side down. Install the screw (refer to Figure 5-63 Install Screw). Screw Side Panel Figure 5-63 Install Screw Attach the side panel to the side of the 8LKD (LD)-L...
  • Page 332: Installing The 8Lki (Ld)-L Unit

    Issue 7.0 UNIVERGE SV8100 Figure 5-64 8LKI (LD)-L UNIT 5.2.3.1 Installing the 8LKI (LD)-L UNIT To prevent possible damage to the 8LKI (LD)-L UNIT or the ITL multiline terminal during installation or removal, disconnect the line cord/LAN cable and the AC/DC adapter from the ITL multiline terminal.
  • Page 333 UNIVERGE SV8100 Issue 7.0 Remove the screw (refer to Figure 5-65 Remove Side Panel from Multiline Terminal on page 5-60). Carefully, return the multiline terminal to the buttons side up position. Remove the soft keys and line key kit from the telephone.
  • Page 334 Issue 7.0 UNIVERGE SV8100 Guide Projection Guide (One Each Side) Figure 5-67 Ribbon Cable Installed Align the projections on the bottom of the 8LKI (LD)-L UNIT into the guide holes on top of the multiline terminal (refer to Figure 5-67 Ribbon Cable Installed).
  • Page 335: Dcl-60-1 (Bk) Console/Dcl-60-1 (Wh) Console

    UNIVERGE SV8100 Issue 7.0 Holding the LCD in place, turn the multiline terminal button side down. Install screw (refer to Figure 5-69 Install Screw). Screw Side Panel Figure 5-69 Install Screw Attach the side panel to the side of the 8LKI (LD)-L...
  • Page 336: Installing The Dcl-60-1 Console

    Issue 7.0 UNIVERGE SV8100 Keep the following in mind when installing DSS Consoles: A 60-Button DSS Console requires a separate digital station port when pairing with a digital keyset. For IP terminals, the first console is connected to the side option slot using a special cable.
  • Page 337 UNIVERGE SV8100 Issue 7.0 Pry the side panel from the multiline terminal. Side Panel Figure 5-71 Remove Side Panel from Multiline Terminal Turn the multiline terminal button side up. Fit the projections of the supplied bracket into the side of the multiline terminal.
  • Page 338 Issue 7.0 UNIVERGE SV8100 Carefully push the Serial cable into the Serial Cable Groove (ITL, DT700 only). Figure 5-73 Press Serial Cable into Groove Using the guides, slide the DCL-60-1 onto the installed bracket (refer to Figure 5-73 Press Serial Cable into Groove).
  • Page 339 UNIVERGE SV8100 Issue 7.0 Open the small door covering the side option connectors by pulling the cover latch toward you (refer to Figure 5-75 Serial Cable Installed, ITL, DT700 only). Connect the cable from the DCL-60-1 CONSOLE to the Side Option Connector on the multiline terminal and close the cover (ITL, DT700 only).
  • Page 340: Lcd (Bl)-L (Bk) Unit/Lcd (Bl)-L (Wh) Unit

    Issue 7.0 UNIVERGE SV8100 Figure 5-76 Connect AC Adapter Cable Complete the installation by reattaching both plastic panels to the front of the multiline terminal. Figure 5-77 DCL-60-1 CONSOLE Installed 5.2.5 LCD (BL)-L (BK) UNIT/LCD (BL)-L (WH) UNIT The LCD (BL)-L UNIT is an optional LCD unit for modular terminals and supports the backlit LCD feature (DT300 Series only).
  • Page 341: Panel( )-L Unit

    UNIVERGE SV8100 Issue 7.0 Figure 5-78 LCD (BL)-L UNIT 5.2.6 PANEL( )-L UNIT Optional plastic color side panels that allow users to customize the ITL/DTL terminals. The following colors are available for the Base (all), VLCD (Value LCD) and SLCD (Sophi LCD) terminals:...
  • Page 342 Issue 7.0 UNIVERGE SV8100 Attach the WM-L UNIT to the wall using four screws (refer to Figure 5-80 Attach the WM-L UNIT to Wall). Screws Screws Figure 5-80 Attach the WM-L UNIT to Wall Align the four cutouts with the four tabs on the WM-L UNIT...
  • Page 343: Release The Wm-L Unit

    UNIVERGE SV8100 Issue 7.0 Push down on telephone until the WM-L UNIT snaps into place (refer to Figure 5-82 WM-L UNIT Installed). Figure 5-82 WM-L UNIT Installed 5.2.8 Release the WM-L UNIT To release the telephone from the WM-L UNIT, press the...
  • Page 344: Wm-L Unit Attached To Wall Plate

    Issue 7.0 UNIVERGE SV8100 5.2.9 WM-L UNIT Attached to Wall Plate The WM-L UNIT (Wall Mount Unit) is used to attach any DT300/ DT700 Series multiline terminal to the wall plate This unit connects to the back side of the telephone.
  • Page 345 UNIVERGE SV8100 Issue 7.0 Cutouts Cutouts Figure 5-85 Cutouts for WM-L UNIT Push up on the WM-L UNIT until it snaps into place (refer to Figure 5-86 WM-L UNIT Installed). Figure 5-86 WM-L UNIT Installed System Hardware Manual 5 - 73...
  • Page 346: Removing The Multiline Terminal From The Wall Mounted Plate

    Issue 7.0 UNIVERGE SV8100 Align the two holes on the back of the WM-L UNIT with the two screws on the wall plate and slide downward (refer to Figure 5-87 Mount Multiline Terminal Wall on Wall Plate). Figure 5-87 Mount Multiline Terminal Wall on Wall Plate Because of strength variation in switch boxes, this method is not recommended.
  • Page 347: Optional Handsets

    Using the PTM handset on an NEC digital or IP terminal prevents eavesdropping and eliminates the worry that privileged information could be transmitted without user authority. These handsets are also an ideal solution to filter unwanted audio transmissions from environments with ambient background noise.
  • Page 348: Utr-1-1 Usb Handset

    UNIVERGE SV8100 UTR-1-1 USB Handset The NEC USB telephone can be plugged directly into a PC USB port, enabling the high quality voice input and output capabilities of a standard desktop telephone. By connecting it to the USB port of a computer, calls can immediately be made and received using a SoftPhone without installation of additional software drivers.
  • Page 349: Wall Mounting

    UNIVERGE SV8100 Issue 7.0 6.3.3 Wall Mounting The UTR-1-1 USB handset can be mounted on the wall using a wall plate or two screws. Align the two holes on the back of the UTR-1-1 and slide down onto the wall plate or screws.
  • Page 350: Bluetooth Cordless Handset

    Issue 7.0 UNIVERGE SV8100 LUETOOTH ORDLESS ANDSET ECTION Bluetooth Cordless Handset (BCH) Interface This optional interface allows the multiline terminal user to use Bluetooth technology to provide a cordless handset. This handset provides: Keyset-like Handset Eight Line Buttons Function Button...
  • Page 351: Selecting A Location

    UNIVERGE SV8100 Issue 7.0 Selecting a Location Before choosing a location for your new telephone, consider these important guidelines: If multiple cordless terminals are installed, keep their Bluetooth cradles at least 3.3 feet (1meter) apart from one another. If the Bluetooth cradle is installed near a metal, concrete wall or any other structure that could affect radio transmission, a communication failure might occur.
  • Page 352: Controls And Indicators

    Issue 7.0 UNIVERGE SV8100 Controls and Indicators Controls and indicators can be found in Figure 5-94 Bluetooth Cradle Controls and Indicators Figure 5-95 Bluetooth Handset Controls and Indicators on page 5-81. Figure 5-94 Bluetooth Cradle Controls and Indicators 5 - 80...
  • Page 353 UNIVERGE SV8100 Issue 7.0 Figure 5-95 Bluetooth Handset Controls and Indicators System Hardware Manual 5 - 81...
  • Page 354: Installing The Bluetooth Cordless Handset

    Issue 7.0 UNIVERGE SV8100 Installing the Bluetooth Cordless Handset The BCH-L (BK) UNIT is an optional device that transforms the standard multifunctional telephone into a cordless terminal. This section explains how to transform the standard hand-set into a BCH-L (BK) UNIT. The BCH-L (BK) UNIT cannot be connected to the DTL-2E-1 or DTL-6DE-1 telephones.
  • Page 355 UNIVERGE SV8100 Issue 7.0 Figure 5-97 Remove Legs From Multiline Terminal Remove the side panel. Disconnect serial connection cord from terminal body. Leave cord connected to the cradle unit. Push the latch to the right to unlock the cradle unit. Then push...
  • Page 356 Issue 7.0 UNIVERGE SV8100 Insert the cradle connecting cable of the Bluetooth Cradle (BTC) into the unit connector. Figure 5-99 Attach Bluetooth Cradle to the Multiline Terminal Fit the projections on the side of the Bluetooth Cradle into the guide holes on the side of the terminal and pull toward you...
  • Page 357 UNIVERGE SV8100 Issue 7.0 Remove the connector cover (rubber) from the bottom of the multiline terminal. Figure 5-101 Removing the Connector Cover Insert the lower claws of the Bottom Unit (see Figure 5-102 Installing the Bottom Unit) into precut holes on the multiline terminal.
  • Page 358 Issue 7.0 UNIVERGE SV8100 Push the latch to release the cover (see Figure 5-103 Stowing the Bottom Unit Cable). Stow the extra bottom unit connecting cable and close the cover. Figure 5-103 Stowing the Bottom Unit Cable Cut or trim the supplied coupled device for the tilt legs handset option.
  • Page 359 UNIVERGE SV8100 Issue 7.0 Reinstall the legs, pushing upwards until both locks snap into place. Set tilt legs to desired position. Return the multiline terminal to the numbered keypad in the up position. Connect the Line cord and the AC adapter.
  • Page 360: Wall Mounting The Bluetooth Cradle

    7.4.2 Wall Mounting the Bluetooth Cradle To prevent possible damage to the BCH-L (BK) UNIT due to falling, NEC recommends installing the unit in a firm position so it will not fall due to its own weight. Clearances required for installing the Bluetooth cradle are shown below.
  • Page 361 UNIVERGE SV8100 Issue 7.0 Figure 5-107 Installing Wood Screws Remove the Bluetooth hanger from the cradle. With a screwdriver, pry from the bottom, and lift the handset hanger from the cradle. Rotate the hanger top to bottom. Slide it downward in the hollow until it clicks into position.
  • Page 362 Issue 7.0 UNIVERGE SV8100 Turn multiline terminal upside down. Lower the tilt leg to the first position (refer to Figure 5-96 Separate Tilt Leg from Leg Support). Stoppers Tilt Leg Figure 5-109 Separate Tilt Leg from Leg Support Hook the wall mount holes (C and D) on the back of the terminal on wood screws (c and d) installed.
  • Page 363: Remove And Replace Handset Battery

    UNIVERGE SV8100 Issue 7.0 7.4.3 Remove and Replace Handset Battery The battery loaded in the Bluetooth handset has a useful life of about two years, depending on how the handset is used. If the battery voltage diminishes quickly after the battery has been charged for a long time, replace with a new Li-ion battery.
  • Page 364: Bluetooth Hub Adapter

    Issue 7.0 UNIVERGE SV8100 LUETOOTH DAPTER ECTION Bluetooth Hub Adapter (BHA) Features The BHA-L UNIT adapter connects a Bluetooth device to a multiline terminal. The BHA-L UNIT cannot be connected to the DTL-2E-1 or DTL-6DE-1 telephone. 8.1.1 Installing the BHA-L UNIT...
  • Page 365 UNIVERGE SV8100 Issue 7.0 Figure 5-114 Removing the Connector Cover Insert the lower claws of the Bottom Unit (see Figure 5-115 Installing the BHA-L UNIT) into precut holes on the multiline terminal. Figure 5-115 Installing the BHA-L UNIT Align connector on inside of BHA-L UNIT and push down until unit snaps into place.
  • Page 366: Pairing A Bluetooth Device And Multiline Terminal (Bluetooth Installed)

    Issue 7.0 UNIVERGE SV8100 8.1.2 Pairing a Bluetooth Device and Multiline Terminal (Bluetooth Installed) Access the Bluetooth screen from a multiline terminal menu and register the Bluetooth headset with the BHA-L UNIT. 8.1.2.1 Accessing the Bluetooth Device Setup Screen From the multiline terminal, access the setup screen...
  • Page 367: Connecting The Paired Device

    UNIVERGE SV8100 Issue 7.0 8.1.2.4 Connecting the Paired Device Enable the Bluetooth device. Select [2. Enable] in the connection screen. After pairing a Bluetooth device, be sure to configure its connection to enable it. If settings are not completed, the Bluetooth device that does the pairing cannot be used.
  • Page 368: Bt Information

    Issue 7.0 UNIVERGE SV8100 8.1.2.7 BT Information You can view the following kinds of information about the BHA-L UNIT: Firmware and hardware versions. Bluetooth module information and standard. Installed profile versions. Device address and name. Figure 5-121 Setting Bluetooth Information...
  • Page 369: Single Line Telephone

    UNIVERGE SV8100 Issue 7.0 INGLE ELEPHONE ECTION Installing the SLT Adapter The Single Line Telephone adapter provides an interface for Single Line Telephones and other similar devices from an ESI channel. This adapter can be connected to any ESI port.
  • Page 370: Wall-Mounting The Slt Adapter

    Issue 7.0 UNIVERGE SV8100 Modular Terminal Modular Terminal SLTII(1)-U( ) ADP To ESIU Base Base CD-8DLCA or Cord Cord ESI Port ESI Port CD-16DLCA Modular Terminal Connections Modular Terminal Connections ESIU Port ESIU Single Line Telephone Connections Figure 5-123 Connecting the SLT Adapter Wall-Mounting the SLT Adapter Unplug the two line cords from the SLT Adapter.
  • Page 371 UNIVERGE SV8100 Issue 7.0 Using the two screws provided with the SLT Adapter, attach the back cover to the desired location. Figure 5-125 Attaching the Unit Replace the front cover and the two screws removed in Step 2. Plug the two modular line cords back into the SLT Adapter which were removed in Step 1.
  • Page 372: Section 10 D Term ® Cordless Dect (Dtl-8R-1)

    UNIVERGE SV8100 DECT (DTL-8R-1) term ® ORDLESS ECTION DTL-8R-1 is a cordless telephone that is adapted for digital NEC PBX (Private Branch Exchange. It is designed for use in the office environment. term ® Figure 5-126 Cordless DECT (DTL-8R-1) A Handset and wired phone cannot be used at the same time.
  • Page 373: Specifications

    UNIVERGE SV8100 Issue 7.0 Figure 5-127 System Overview 10.1 Specifications The UNIVERGE SV8100 complies with FCC and IC part 15. General RoHs Frequency 1.9G (1880 ~ 1900 MHz) Audio Process Digital (ADPCM) Operating Temperature 0⋅ ~ +50⋅ C (+32⋅ F to +122⋅ F)
  • Page 374: Battery Safety

    Issue 7.0 UNIVERGE SV8100 Power Requirements 10 Vdc from supplied AC adapter Size 58mm (H) x 215mm (D) x 130mm (W) Weight 410g Handset Receive/Transmit Frequency 1880 ~ 1900 MHz Power Requirements Nickel-Metal Hydride battery pack Size 163mm (H) x 31mm (D) x 55mm (W)
  • Page 375: Important Safety Instructions

    UNIVERGE SV8100 Issue 7.0 Charge the battery pack provided with or identified for use with this product only in accordance with the instructions and limitations specified in the instruction manual provided for this product. Observe proper polarity orientation between the battery pack and battery charger.
  • Page 376: Important Electrical Considerations

    Issue 7.0 UNIVERGE SV8100 risks. Incorrect reassembly can cause electric shock when the appliance is subsequently used. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: When the power supply cord is damaged or frayed.
  • Page 377 UNIVERGE SV8100 Issue 7.0 Changes or modifications to this product not expressly approved by NEC Unified Solutions, or operation of this product in any way other than as detailed by this manual, could void your authority to operate this product.
  • Page 378 Issue 7.0 UNIVERGE SV8100 Range Nominal values of the DECT system are: 164 feet (50 meters) – Indoor 984 feet (300 meters) – Outdoor The telephone is designed to achieve a maximum range of up to 350 feet (107 metres) (depending upon the environment). This phone has been rated to operate at a maximum distance with the qualification that the range depends upon the environment in which the telephone is used.
  • Page 379: Selecting A Location

    UNIVERGE SV8100 Issue 7.0 The DTL-8R-1 is limited to five RF channels. The RF channel is changed automatically to find the best channel. Depending on your environment, the maximum number of cordless devices used without interference varies. Multiple base and handset units should not be closer than 20 feet at any time.
  • Page 380 Connect the cord from the telephone jack to the Line In on the D Cordless DECT. Figure 5-128 Connecting Telephone Cords to the Telephone Jack term Connect a qualified NEC digital multiline terminal to the D Cordless DECT. Line "OUT"...
  • Page 381: Applying Power To The Charging Unit

    UNIVERGE SV8100 Issue 7.0 10.8 Applying Power to the Charging Unit The unique design of the telephone allows the user to place the handset in the charging unit with or without the belt clip attached. The charging unit can charge a second battery with or without the handset being charged. The battery packs can automatically be recharged either in or out of the handset.
  • Page 382: Mounting The Base To A Standard Wall Plate

    Issue 7.0 UNIVERGE SV8100 Figure 5-131 Polarized Plug 10.9 Mounting the Base to a Standard Wall Plate The base unit is designed to be mounted on standard wall plate. To attach the wall mount stand to the base unit: Slide the wall mount stand into the notches at the top of the base unit.
  • Page 383 Figure 5-133 Placing the AC Adapter Cord Inside the Wall Mount Stand Plug one end of the short telephone cord (locally supplied) in the LINE jack on the base unit. Plug one end of the NEC digital multiline terminal into the PHONE jack. Place the telephone cords inside the molded channels on the bottom of the wall mount stand.
  • Page 384 Issue 7.0 UNIVERGE SV8100 Plug the other end of the short telephone cord into the modular wall jack in the center of the wall plate. Place the base unit on the posts of the wall plate and push down until it is firmly seated.
  • Page 385: 10.10 Mounting The Base Directly To The Wall

    Plug the AC adapter into the base unit. Plug one end of the short telephone cord into the LINE jack on the base unit. Then plug one end of an NEC multiline terminal into the PHONE jack. Place the telephone cords inside the molded channels on the bottom of the wall mount stand.
  • Page 386 Issue 7.0 UNIVERGE SV8100 Figure 5-137 Placing the Telephone Cords Inside the Wall Mount Stand Place the base unit on the posts of the wall screws and push down until it is firmly seated. Figure 5-138 Attaching the Wall Mount Unit to the Wall Plug the other end of the short telephone cord into a telephone wall jack.
  • Page 387: 10.11 Wall Mounting The Charging Unit

    UNIVERGE SV8100 Issue 7.0 10.11 Wall Mounting the Charging Unit The charging unit is also designed to be wall mounted. Before mounting the charging unit, consider the following: Select a location away from electrical cables, pipes, or other items behind the mounting location that could cause a hazard when inserting screws into the wall.
  • Page 388: 10.12 Attaching And Removing The Belt Clip

    Issue 7.0 UNIVERGE SV8100 Place the charging unit on the posts of the wall screws and push down until it is firmly seated. Figure 5-141 Placing the Charging Unit on the Wall Plug the AC adapter into a standard 230 Vac wall outlet. Refer to...
  • Page 389: 10.13 Installing The Handset Battery Pack

    UNIVERGE SV8100 Issue 7.0 To remove the clip, press the retaining clip in toward the belt clip blade and slide the clip up at the same time. Figure 5-143 Removing the Belt Clip 10.13 Installing the Handset Battery Pack term ®...
  • Page 390: 10.14 Charging Batteries

    Issue 7.0 UNIVERGE SV8100 Slide the battery pack down into the handset. It may be necessary to remove the old battery at this time. Figure 5-145 Replacing the Battery Pack Replace the cover and slide it up until it latches onto the handset.
  • Page 391: Section 11 Ml440/Ap300 Cordless Handset

    UNIVERGE SV8100 Issue 7.0 ML440/AP300 C ORDLESS HANDSET ECTION The ML440/AP300 chapter outlines the steps for connecting and mounting the base station, charging the battery and powering on the handset. 11.1 Connecting the Base Station If your network connection does not provide Power Over Ethernet, you will need to order a base station AC adapter and a standard Ethernet-to-PoE adapter.
  • Page 392 Issue 7.0 UNIVERGE SV8100 Route the cable through the channel. Figure 5-148 Install AP300 Base Station Connect the other end of the cable to your TCP/IP network. When the base station powers on, the STATUS LED on the front briefly lights yellow and then turns off while it initializes and connects to the network.
  • Page 393: Base Station Wall Mounting Installation

    UNIVERGE SV8100 Issue 7.0 LED Status State Meaning RED Steady On Power but FPGA starting up RED Flashing Trying to connect to the network Lower LED, Network status display and showing network red/Green Green Flashing activity. AP300 operational 11.2 Base Station Wall Mounting Installation Ensure the wall can support the weight of the base station.
  • Page 394: Handset And Charger

    Issue 7.0 UNIVERGE SV8100 11.3 Handset and Charger Figure 5-150 ML440 Handset - Front View on page 5-122 provides a front view of the handset. Figure 5-151 ML440 - Handset Charger on page 5-123 provides a to view of the charger.
  • Page 395: Charging The Battery

    UNIVERGE SV8100 Issue 7.0 Figure 5-151 ML440 - Handset Charger 11.4 Charging the Battery Install the handset battery as shown. Remove the battery cover Insert the bottom of the battery into Replace the battery cover from the back of the handset.
  • Page 396: Powering On The Handset

    Issue 7.0 UNIVERGE SV8100 Use the charger AC adapter to connect the charger’s AC jack to a standard electrical outlet. Place the handset in th echarger with the display facing forward. the HANDSET STATUS LED should turn on; if it doesn’t, reseat the handset or try plugging the AC adapter into a different outlet.
  • Page 397: Chapter 6 Installing Sv8100 Optional Equipment

    Installing SV8100 Optional Equipment ENERAL NFORMATION ECTION This chapter provides information for installing optional equipment, such as term PGD(2)-U10 ADPs, background music, door boxes, DSS consoles, D VSR, external paging as well as other handsets, recording devices and Chapter adapters on the SV8100 digital and IP telephones. PGD(2)-U10 ADP ECTION Using a PGD(2)-U10 ADP...
  • Page 398: Led Indications

    Issue 7.0 UNIVERGE SV8100 The PGD(2)-U10 ADP connects to any available digital extension port. The terminal connections made within the PGD(2)-U10 ADP and the jumper settings determine what features are used for each circuit. Channel 2 Channel 1 Status LED...
  • Page 399 UNIVERGE SV8100 Issue 7.0 Remove the screw from the front of the PGD(2)-U10 ADP. Figure 6-2 Remove Cover from PGD(2)-U10 ADP Using a screwdriver, break out the plastic piece covering the cable hole. Figure 6-3 Remove Plastic Cover from Cable Hole Set the S3 –...
  • Page 400 Issue 7.0 UNIVERGE SV8100 Table 6-2 PGD(2)-U10 ADP S3 – S6 Jumper Settings Function LED Indication Open Open Door Box On when in use. Open Short External Paging Speaker On when in use. Channel 1 Short Open External Ringer On when in use.
  • Page 401 UNIVERGE SV8100 Issue 7.0 Strip one end of the cable to be connected to the control relay or door box so that approximately 1/4” (8 mm) of bare wire is exposed. Insert the cable into the proper CN4 or CN5 location while holding down the lock button (holding down this lock button is easiest with a flat-head screwdriver).
  • Page 402 Issue 7.0 UNIVERGE SV8100 Figure 6-5 PGD(2)-U10 ADP Connection Diagram 6 - 6 Installing SV8100 Optional Equipment...
  • Page 403 UNIVERGE SV8100 Issue 7.0 Flat-head screwdriver Cable Press down CN4, CN5 Figure 6-6 Connecting Cable to the PGD(2)-U10 ADP Repeat Steps 4 and 5 for any additional connections required. Replace the cover and tighten the screw to hold the cover in place.
  • Page 404 Issue 7.0 UNIVERGE SV8100 Figure 6-7 PGD(2)-U10 ADP Connections Install a modular jack for each PGD(2)-U10 ADP. For each module, run one-pair 24 AWG station cable from the cross-connect block to a modular jack. Ground the unused pair. Terminate the extension leads to GRN/RED of the modular jack.
  • Page 405 UNIVERGE SV8100 Issue 7.0 fits best for your location. Figure 6-8 Installing the Screws The back of the PGD(2)-U10 ADP has two key-hole type openings. Place the PGD(2)-U10 ADP over the two screws and slide it down or over (depending on the positioning) to lock it in place.
  • Page 406: Background Music

    Issue 7.0 UNIVERGE SV8100 ACKGROUND USIC ECTION Installing Background Music Background Music (BGM) sends music from a customer-provided music source to speakers in keysets. If an extension user activates it, BGM plays whenever the user’s extension is idle. Connecting to the CD-CP00: Connect an RCA line from the CN8 or CN9 connector on the CD-CP00 to the appropriate location on the extension cross-connect block.
  • Page 407: Door Box

    UNIVERGE SV8100 Issue 7.0 ECTION Installing a Door Box A PGD(2)-U10 ADP is required for this option. The Door Box is a self-contained, water-resistant, Intercom unit typically used to monitor an entrance door. A visitor at the door can press the Door Box call button (like a door bell).
  • Page 408 Issue 7.0 UNIVERGE SV8100 Remove the back half of the Door Box and attach this mounting bracket to the wall with the two screws provided. Connect the two-conductor station cable from the CN4 connectors within the PGD(2)-U10 ADP to the Door Box terminals. These wires must be routed through the opening in the bottom of the Door Box mounting bracket.
  • Page 409 UNIVERGE SV8100 Issue 7.0 Figure 6-11 Setting the PGD(2)-U10 ADP for a Door Box System Hardware Manual 6 - 13...
  • Page 410 Issue 7.0 UNIVERGE SV8100 Figure 6-12 Installing a Door Box 6 - 14 Installing SV8100 Optional Equipment...
  • Page 411: External Paging

    UNIVERGE SV8100 Issue 7.0 XTERNAL AGING ECTION External Page Two external page zone/door box circuits are provided by each PGD(2)-U10 ADP installed. Each Door Box/external page circuit provides a dry relay contact. The CD-CP00 also provides a connection for external paging and a relay.
  • Page 412 Issue 7.0 UNIVERGE SV8100 Terminate the extension leads to GRN/RED of the modular jack. Terminate the unused leads to the jack. Install bridging clips as required. Plug a modular line cord from the mod jack to the CN1 connector on the PGD(2)-U10 ADP.
  • Page 413: External Paging And Door Box

    UNIVERGE SV8100 Issue 7.0 The PGD(2)-U10 ADP provides amplifiers for each page output port (for a maximum of +8 dBM, 600 ohms at 1KHz). No additional page amplification is provided by the PGD(2)-U10 ADP but, if required, an external page amplifier can be used for additional amplification.
  • Page 414: Door Box /External Page Relay Contacts

    Issue 7.0 UNIVERGE SV8100 Door Box /External Page Relay Contacts 6.2.1 Connecting a Contact Relay Device to a Door Box/External Page Relay To connect a dry contact relay device to a Door Box/External Page Relay: To connect to the CD-CP00:...
  • Page 415: External Recording System/External Ringer

    UNIVERGE SV8100 Issue 7.0 The relay closes when the Door Box/external page zone is called. The maximum applied voltage is 24vDC at .5A for each contact. Figure 6-14 CD-CP00 Page Connections XTERNAL ECORDING YSTEM XTERNAL INGER ECTION External Recording System or External Ringer The PGD(2)-U10 ADP allows the connection of an external recording system or external ringer.
  • Page 416: Installing An External Recording System Or External Ringer

    Issue 7.0 UNIVERGE SV8100 Installing an External Recording System or External Ringer To connect to the PGD(2)-U10 ADP: Make sure the jumper in the PGD(2)-U10 ADP for the channel is set correctly. (Refer to Figure 6-4 PGD(2)-U10 ADP Jumper Settings page 6-4).
  • Page 417: Programming

    UNIVERGE SV8100 Issue 7.0 Figure 6-15 PGD(2)-U10 ADP Cable Connection Programming 10-03-01 : ETU Setup – Terminal Type (Circuit 1) 10-03-06 : ETU Setup – Terminal Type (Circuit 2) Confirm that the PGD(2)-U10 ADP has defined the circuit type as either type 7 for External Ringer or 9 for ACIs.
  • Page 418 Issue 7.0 UNIVERGE SV8100 11-08-01 : ACI Group Pilot Number Assign pilot numbers to ACI groups. When a user dials the pilot number, they reach an available ACI software port within the group. Aspire S: ACI Groups 1-4 Aspire: ACI Groups 1-16...
  • Page 419 UNIVERGE SV8100 Issue 7.0 15-12-01 : Conversation Recording Destination for Extensions - ACI Recording Destination Extension Number Use this option to assign the ACI Call Recording destination on a per extension basis. The destination can be an ACI port’s extension number (assigned in Program 11-06) or an ACI Department Group pilot number (assigned in Program 11-08).
  • Page 420: Music Sources

    Issue 7.0 UNIVERGE SV8100 USIC OURCES ECTION Music on Hold The system can provide Music on Hold from either an internally synthesized source on the CD-CP00 or from an external source. The external MOH can be a tuner, tape deck, CD player, etc. The settings in Program 10-04-01 and 14-08-01 determine whether the source for MOH is internal or external.
  • Page 421 UNIVERGE SV8100 Issue 7.0 Install a modular jack for each PGD(2)-U10 ADP. For each module, run one-pair 24 AWG station cable from the cross-connect block to a modular jack. Ground the unused pair. Terminate the extension leads to GRN/RED of the modular jack.
  • Page 422 Issue 7.0 UNIVERGE SV8100 Figure 6-17 PGD(2)-U10 ADP Connections 6 - 26 Installing SV8100 Optional Equipment...
  • Page 423: Night Mode Selection

    UNIVERGE SV8100 Issue 7.0 IGHT ELECTION ECTION Night Mode Selector Switch The Night Mode Switch relay closes when the system detects either an open or closure on the MISC block NIGHT SW terminals. Maximum 48v DC is output to the switch when open, and 7mA DC when shorted.
  • Page 424: Removing The Faceplate

    Issue 7.0 UNIVERGE SV8100 10.1.1 Removing the Faceplate Use the small notch at the lower right corner of the telephone, to lift the faceplate up. Each corner has a plastic locking pin which releases as the faceplate is lifted up.
  • Page 425: Section 11 Telephone Adapters

    The ILPA does the negotiation and detection with the switch and then relays the power to the IP terminal device. This provides an additional way to power the NEC IP terminals. With this adapter, the IP terminals on the UNIVERGE SV8100 system can be powered using:...
  • Page 426: Conditions

    Issue 7.0 UNIVERGE SV8100 NEC power supply PoE-managed switch (BlueFire 200/24) (in-line and spare pair detection) Router Blade (spare pair detection) Cisco Data Switch – CDP supported (in-line and spare pair detection) In-Line Power Adapter Figure 6-20 In-Line Power Adapter 11.2.1...
  • Page 427: Installation

    SW1 Setting IEEE802.3af STD System Cisco Discovery Protocol System NEC BlueFire 200/24 Switch Set the switch setting on the NEC IPhone or IP adapter to the correct position. IPhone (SW2) or IP Adapter (SW1) SW Setting NEC Power Patch Panel...
  • Page 428 Issue 7.0 UNIVERGE SV8100 Connect the NEC VoIP telephone to the TEL connector on the ILPA-R adapter with the LAN cable provided with the adapter. If a customer-provided cable is used, the total length from the switch to the telephone should be less than 328 feet.
  • Page 429: Ada-L Unit

    UNIVERGE SV8100 Issue 7.0 11.3 ADA-L UNIT Using the ADA-L UNIT (Ancillary Device Adapter) provides a recording jack connection from a telephone to an external tape recorder, speaker or PC. Both sides of the conversation are recorded. The adapter output is a 1/8” audio (mono) jack which you can connect directly to an AUX level input on a recorder or page amplifier.
  • Page 430: Ada-L Unit Switch Settings

    Issue 7.0 UNIVERGE SV8100 11.3.1 ADA-L UNIT Switch Settings Figure 6-23 ADA-L UNIT shows the location of the switches. The dip switches (DSW) allow a technician to configure the unit for specific settings. Due to location, set switches prior to installation of ADA-L on DTL/ITL multiline terminal.
  • Page 431: Installing The Ada-L Unit

    UNIVERGE SV8100 Issue 7.0 Table 6-3 ADA-L Unit Switch Settings (Continued) Switch Description/Settings Output Hook Signal to External Device DSW 1 On = Output Off = No Output (Default) Record Confirmation Tone Switches DSW 2 On = Tone On (DSW)
  • Page 432 Issue 7.0 UNIVERGE SV8100 Push the two stopper tabs through the slots to separate the tilt leg from the leg support. Lay the tilt leg and the leg support flat to expose ADA-L UNIT compartment. Carefully pry loose the knockout covering the bottom option...
  • Page 433: Ada-L Unit Connection

    UNIVERGE SV8100 Issue 7.0 11.3.3 ADA-L UNIT Connection The mini-plug connection cord should not use an attenuator and have a monaural (single ring) mini-plug connection for normal recording. 11.3.3.1 ADA-L UNIT Connection for Recording Only Set the ADA-L UNIT DSW switches (Refer to...
  • Page 434: Ada-L Unit Connection For Sending Recorded Calls To The Telephone

    Issue 7.0 UNIVERGE SV8100 11.3.3.2 ADA-L UNIT Connection for Sending Recorded Calls to the Telephone Set the ADA-L UNIT DSW switches (see Figure 6-23 ADA-L UNIT on page 6-34). Set DSW 6 to ON. When sending recorded calls to the telephone, set DSW switch 1 to ON.
  • Page 435: Apr-L Unit Switch Settings

    UNIVERGE SV8100 Issue 7.0 When installing or removing the adapters, the telephone should be unplugged from the system. If it is the intention to use the APR-L UNIT to connect to a fax machine, it should be noted that the APR-L UNIT provides 24v and some fax machines require 48v to operate correctly.
  • Page 436: Installing The Apr-L Unit

    Issue 7.0 UNIVERGE SV8100 impedance (factory setting is 1). 11.4.2 Installing the APR-L UNIT Perform the following to connect the APR-L UNIT to the Bottom Option Interface located underneath the DTL multiline terminal. Only one APR-L UNIT can be installed.
  • Page 437 UNIVERGE SV8100 Issue 7.0 Bottom Option Knockout Interface Figure 6-31 Bottom Option Interface Knockout Using the exposed Bottom Option Interface as a guide, install the APR-L UNIT in the bottom of the DTL multiline terminal. Push down until left and right tabs are seated (Refer to...
  • Page 438 Issue 7.0 UNIVERGE SV8100 Figure 6-33 Ferrite Bead with APR Adapter Plug the end of the line cord for the analog device which has the ferrite bead closest to it into the jack on the adapter. Connect the opposite end to the analog device.
  • Page 439: Psa-L (Bk) Unit / Psa-L (Wh) Unit

    UNIVERGE SV8100 Issue 7.0 11.5 PSA-L (BK) UNIT PSA-L (WH) UNIT The PSA-L UNIT (Power Save Adapter), an optional adapter for the ITL/DTL Terminals, is used with IP telephones to make or receive a call using the Public Switched Telephone Network (PSTN) when a call cannot be made or received using the Local Area Network (LAN).
  • Page 440: Installing The Psa-L Adapter

    Issue 7.0 UNIVERGE SV8100 PSTN DTMF/DP Figure 6-35 PSA-L UNIT Connections 11.5.1 Installing the PSA-L Adapter Before installing or removing the PSA-L adapter, remove the line cord, LAN cable, and then AC adapter from the outlet. Turn multiline terminal upside down.
  • Page 441 UNIVERGE SV8100 Issue 7.0 Stoppers Tilt Leg Figure 6-36 Separate Tilt Leg from Leg Support Push the two stopper tabs through the slots to separate the tilt leg from the leg support. Lay the tilt leg and the leg support flat.
  • Page 442 Issue 7.0 UNIVERGE SV8100 Push latch to right to unlock the cradle unit. Then push the cradle unit forward to separate from the terminal body. Latch Figure 6-38 Bottom of Multiline Terminal (Legs Removed) Fit the projections on the side of the PSA-L UNIT into the guide holes on the side of the terminal and pull toward you until the PSA-L UNIT snaps into place.
  • Page 443 UNIVERGE SV8100 Issue 7.0 Gently press the serial cable into the grooved cutout for the cable. Cable Groove Figure 6-40 Grooved Cutout for Serial Cable Connect the serial connection cord (refer to Figure 6-39 Attach PSA-L Unit to the Multiline Terminal on page 6-46) from the PSA-L UNIT to the terminal body.
  • Page 444 Issue 7.0 UNIVERGE SV8100 For the Handset, set the connector in place. Figure 6-42 Insert Connector for Handset Use Attach the analog trunk cable and the handset cable. Refer to Figure 6-35 PSA-L UNIT Connections on page 6-44. Reinstall the legs, pushing upwards until both locks snap into place.
  • Page 445 UNIVERGE SV8100 Issue 7.0 Pull tab down and lift out the numbered keypad panel. Figure 6-44 Remove Numbered Keypad Install the new keypad panel supplied with the PSA-L UNIT. Figure 6-45 Install Numbered Keypad Reinstall both plastic panels to the front of the multiline terminal...
  • Page 446: Using The Psa-L Adapter

    Issue 7.0 UNIVERGE SV8100 Figure 6-46 Install Plastic Panels Connect the line cord to the adapter. Connect the user system (KTS or PBX) cable. If required, remove the side panel from the original cradle unit. 11.5.2 Using the PSA-L Adapter...
  • Page 447: Gigabit Adapter (Gba-L Unit)

    UNIVERGE SV8100 Issue 7.0 Answering Calls: If you receive a call via PSTN during a conversation via LAN, answer the call by completing the LAN call and placing the handset back into the cradle. Change the LAN/PSTN Change Switch to PSTN and then lift the handset to answer the call.
  • Page 448: Installing The Gba-L Unit

    Issue 7.0 UNIVERGE SV8100 Figure 6-47 GBA-L UNIT 11.6.1 Installing the GBA-L UNIT Before installing or removing the GBA-L UNIT, remove the line cord, LAN cable, and then AC adapter from the outlet. Turn multiline terminal upside down. Unplug the line cord and handset cord from the multiline terminal.
  • Page 449 UNIVERGE SV8100 Issue 7.0 Stoppers Tilt Leg Figure 6-48 Separate Tilt Leg from Leg Support Push the two stopper tabs through the slots to separate the tilt leg from the leg support. Lay the tilt leg and the leg support flat.
  • Page 450 Issue 7.0 UNIVERGE SV8100 Plug in the LAN cable and gently press the cable into the grooved cutout (refer to Figure 6-50 Attach the LAN Cable). Figure 6-50 Attach the LAN Cable Plug in the DC power cable and gently press the cable into the...
  • Page 451 UNIVERGE SV8100 Issue 7.0 Assemble the legs and bracket then align with tab holes (refer Figure 6-52 Align Bracket with Terminal). Figure 6-52 Align Bracket with Terminal Pass the LAN and DC power cables through the bracket (refer Figure 6-53 Pass Cabling Through Bracket).
  • Page 452 Issue 7.0 UNIVERGE SV8100 Slide the supporting bracket forward until a click is heard (refer Figure 6-54 Secure Bracket to Terminal). Figure 6-54 Secure Bracket to Terminal Secure base of GBA-L UNIT to bracket assembly (refer to Figure 6-55 Secure GBA-L UNIT Base to Bracket Assembly).
  • Page 453 UNIVERGE SV8100 Issue 7.0 Install the NEC provided Cat 5 Ethernet cable (refer to Figure 6-56 IP Phone(X) Connection). Figure 6-56 IP Phone(X) Connection Install the NEC provided Cat 5 Ethernet cable (refer to Figure 6-57 PC(X) Connection). Figure 6-57 PC(X) Connection...
  • Page 454 Issue 7.0 UNIVERGE SV8100 Install the NEC provided power cable (refer to Figure 6-58 DC Power Connection). Figure 6-58 DC Power Connection Connect the Core then plug in the Network connection cable (refer to Figure 6-59 LAN(=) Connection). Figure 6-59 LAN(=) Connection...
  • Page 455 UNIVERGE SV8100 Issue 7.0 Install the cable from the optional external AC adapter (refer to Figure 6-60 AC to DC In Connection). Figure 6-60 AC to DC In Connection The AC Adapter (AC-L UNIT) must be ordered separately. Cable installation for the GBA-L UNIT complete (refer to...
  • Page 456: Gba-L Unit Connection

    Issue 7.0 UNIVERGE SV8100 11.6.2 GBA-L UNIT Connection The following chart outlines the connectivity available to the GBA-L UNIT: Figure 6-62 GBA-L UNIT Connectivity Chart 11.6.3 LED Display The following provides a list of each LED and associated operation and status indications. Refer to...
  • Page 457: Power Failure

    UNIVERGE SV8100 Issue 7.0 When 1000Mbps is When 100Mbps is When 10Mbps is LED Name Connected Connected Connected SPEED Display Green Lighting Red Lighting Turning Off LED Name At LINK (At the Data Communication) LINK/ACT Display Green Lighting Green Blinking...
  • Page 458: Section 12 Power Failure Telephones

    Issue 7.0 UNIVERGE SV8100 When connecting the RJ-61 cables to the COIU Blade, note the position of the Power Failure connector. Do not confuse connector CN3 as the CN2 trunk connector. 12.2 Connector Pin-Outs on COIU Blade for Power Failure Circuits...
  • Page 459 UNIVERGE SV8100 Issue 7.0 Figure 6-64 Power Failure Connector (CN3) Shown on CD-4COTA Blade System Hardware Manual 6 - 63...
  • Page 460 Issue 7.0 UNIVERGE SV8100 6 - 64 Installing SV8100 Optional Equipment...
  • Page 461 THIS PAGE IS INTENTIONALLY LEFT BLANK...
  • Page 462 NEC reserves the right to change the specifications, functions, or features at any time without notice. NEC has prepared this document for use by its employees and customers. The information contained herein is the property of NEC and shall not be reproduced without prior written approval of NEC .

Table of Contents