Mitsubishi Q00JCPU User Manual page 613

APPENDICES
ACPU Special Special
Special Relay after Relay for
Relay Conversion Modification
M9103 SM1103 SM323
M9104 SM1104 SM324
M9108 SM1108 SM90
M9109 SM1109 SM91
M9110 SM1110 SM92
M9111 SM1111 SM93
M9112 SM1112 SM94
M9113 SM1113 SM95
M9114 SM1114 SM96
M9180 SM1180 SM825
M9181 SM1181 SM822
M9182 SM1182 SM821
M9196 SM1196 SM325
M9197 SM1197
M9198 SM1198
M9199 SM1199
TableApp.11 Special relay
Name Meaning
OFF : Continuous transition
Presence/absence
not effective
of continuous
ON : Continuous transition
transition
effective
Continuous OFF : When transition is
transition completed
suspension flag ON : When no transition
Step transition
watchdog timer
start (equivalent of
SD90)
Step transition
watchdog timer
start (equivalent of
SD91)
Step transition
watchdog timer
start (equivalent of
SD92)
Step transition
OFF : Watchdog timer reset
watchdog timer
ON : Watchdog timer reset
start (equivalent of
start
SD93)
Step transition
watchdog timer
start (equivalent of
SD94)
Step transition
watchdog timer
start (equivalent of
SD95)
Step transition
watchdog timer
start (equivalent of
SD96)
Active step
OFF : Trace started
sampling trace
ON : Trace completed
completion flag
OFF : Trace not being
Active step
executed
sampling trace
ON : Trace execution under
execution flag
way
Active step
OFF : Trace disable/suspend
sampling trace
ON : Trace enable
permission
Operation output OFF : Coil output OFF
at block stop ON : Coil output ON
I/O numbers
SM SM
to be
1197 1198
displayed
OFF OFF X/Y0 to 7F0
Switch between
blown fuse and I/O X/Y800 to
ON OFF
verification error
display
X/Y1000 to
OFF ON
17F0
X/Y1800 to
ON ON
1FF0
Data recovery of
OFF : Data recovery disabled
online sampling
ON : Data recovery enabled
trace/status latch
Details
• Set whether continuous transition will be performed for the
block where the "continuous transition bit" of the SFC
information device is not set.
• OFF during operation in the continuous transition mode or
during continuous transition, and ON when continuous
transition is not executed.
• Always ON during operation in the no continuous
transition mode.
• Turns ON when the measurement of the step transition
watchdog timer is started.
Turning this relay OFF resets the step transition watchdog
timer.
• Set when sampling trace of all specified blocks is
completed. Reset when sampling trace is started.
• Set when sampling trace is being executed.Reset when
sampling trace is completed or suspended
• Selects sampling trace execution enable/disable.
ON : Sampling trace execution is enabled.
OFF : Sampling trace execution is disabled. If turned off
during sampling traceexecution,trace is
suspended.
• Selects the operation output when block stop is executed.
ON : Retains the ON/OFF status of the coil being used
by using operation output of the step being
executed at block stop.
OFF : All coil outputs are turned off. (Operation output
by the SET instruction is retained regardless of
the ON/OFF status of M9196.)
Switches I/O numbers in the fuse blow module storage
registers (SD1100 to SD1107) and I/O module verify error
FF0 storage registers (SD1116 to SD1123) according to the
combination of ON/OFF of the SM1197 and SM1198.
• Recovers the setting data stored in the CPU module at
restart when sampling trace/status latch is executed.
• SM1199 should be ON to execute again. (Unnecessary
when writing the data again from peripheral devices.)
Appendix 1 Special Relay List
9
Corresponding CPU
10
11
QnA
Qn(H)
QnPH
QnA
QnA
Qn(H)
QnPH
App
- 18