Mitsubishi Q00JCPU User Manual page 612

APPENDICES
ACPU Special Special
Special Relay after Relay for
Relay Conversion Modification
M9056 SM1056
M9057 SM1057
M9058 SM1058
M9059 SM1059
M9060 SM1060
M9061 SM1061
M9065 SM1065 SM711
M9066 SM1066 SM712
M9070 SM1070
M9081 SM1081 SM714
M9084 SM1084
M9091 SM1091
M9094 SM1094 SM251
M9100 SM1100 SM320
M9101 SM1101 SM321
M9102 SM1102 SM322
*: The A8UPU/A8PUJ is not available for the QCPU/QnACPU.
App
Appendix 1 Special Relay List
- 17
TableApp.11 Special relay
Name Meaning
OFF : Other than when P, I
Main side P, I set set being requested
request ON : P, I set being
requested
OFF : Other than when P, I
Sub side P, I set set being requested
request ON : P, I set being
requested
Main side P, I set Momentarily ON at P, I set
completion completion
Sub program P, I Momentarily ON at P, I set
set completion completion
OFF : Other than when P, I
Sub program 2 P, I set being requested
set request ON : P, I set being
requested
OFF : Other than when P, I
Sub program 3 P, I set being requested
set request ON : P, I set being
requested
OFF : Divided processing not
Divided processing
underway
execution
ON : During divided
detection
processing
Divided processing OFF : Batch processing
request flag ON : Divided processing
A8UPU/ OFF : Read time not
A8PUJrequired shortened
search time* ON : Read time shortened
OFF : Empty spaces in
communication
Communication request registration
request area
registration area ON : No empty spaces in
BUSY signal communication
request registration
area
OFF : Error check executed
Error check
ON : No error check
Instruction error OFF : No error
flag ON : Error
OFF : Replacement
I/O change flag
ON : No replacement
OFF : SFC programs not
Presence/absence
used
of SFC program
ON : SFC programs used
Start/stop SFC OFF : SFC programs stop
program ON : SFC programs start
SFC program start OFF : Initial Start
status ON : Continue
Details
• Provides P, I set request after transfer of the other
program (for example subprogram when main program is
being run) is complete during run. Automatically switched
off when P, I setting is complete.
• Turned ON once when the P, I set has been completed,
and then turned OFF again.
• Provides P, I set request after transfer of the other
program (for example subprogram when main program is
being run) is complete during run. Automatically switched
off when P, I setting is complete.
• Turned on when canvas screen transfer to AD57(S1)/
AD58 is done by divided processing, and turned off at
completion of divided processing
• Turned on when canvas screen transfer to AD57(S1)/
AD58 is done by divided processing.
• Turned ON to shorten the search time in the A8UPU/
A8PUJ.
(In this case, the scan time is extended by 10 %.)
• Indication of communication enable/disable to remote
terminal modules connected to the AJ71PT32-S3, A2C or
A52G.
It is set whether the error checks below are performed or not
when the END instruction is processed (to set the END
instruction processing time).
• Check for breakage of fuse.
• Check of battery
• Collation check of I/O module
• Turns ON when the detail factor of the operation error is
stored into SD1091.
• Remains ON if the condition is restored to normal
thereafter.
• The I/O module can be changed online (with power on)
when SM251 is turned ON after the head I/O number of
the I/O module is set to SD251. (One module only is
allowed to be changed by one setting.)
• To be switched on in the program or peripheral device test
mode to change the module during CPU RUN. To be
switched on in peripheral device test mode to change the
module during CPU STOP.
• RUN/STOP mode must not be changed until I/O module
change is complete.
• Turned on if the SFC program is registered.
• Turned off if it is not.
• The value in SM320 is set as the initial value.
(The relay automatically turns ON when the SFC program
is present.)
• When this relay turns from ON to OFF, execution of the
SFC program stops.
• When this relay turns from OFF to ON, execution of the
SFC program resumes.
• The SFC program start mode in the SFC setting of the
PLC parameter dialog box is set as the initial value.
At initial start: OFF
At continue start: ON
Corresponding CPU
QnA
Qn(H)
QnPH
QnA
QnA
Qn(H)
QnPH
QnA
QnA
Qn(H)
QnPH
QnA
QnA
Qn(H)
QnPH