Toshiba e-STUDIO6520C Service Handbook page 427

[E030] Power-ON jam
1. Open the cover of the unit/area whose picture is flashing on the control panel and remove if there
is any paper on the transport path. (Refer to the table below.)
2. Is the sensor in the jamming area working? (Perform the input check: Refer to the following
table.)
3. Check if the connector on the PFC board is disconnected from the corresponding sensor in the
jamming area or the harnesses are open circuited. Correct if any.
4. Replace the sensor.
5. Replace the PFC board.
Relation between the jamming area and the corresponding sensors/covers.
(If a jam is occurring in the ADU or LCF check the board in each unit.)
Jamming area
Paper path section Duplexing unit
Fuser Duplexing unit
ADU Duplexing unit
Cover
Bypass unit Duplexing unit
Feeding area Paper feed cover
(equipment)
LCF LCF side cover
Bridge unit Front cover
Upper exit section -
Lower exit section -
Reverse section Reverse path
cover
Finisher Finisher door
[E061]Incorrect paper size setting for 1st drawer
[E062]Incorrect paper size setting for 2nd drawer
[E063]Incorrect paper size setting for 3rd drawer
[E064]Incorrect paper size setting for 4th drawer
[E065]Incorrect paper size setting for bypass tray
If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer
setting and the one in the drawer.
* Paper size detection is performed at the first sheet of paper when the drawer is opened or
closed, or when the power of the equipment is turned ON.
© 2008-2011 TOSHIBA TEC CORPORATION All rights reserved
Cover Sensor
Registration sensor
Transfer belt paper clinging
detection sensor
2nd transfer side paper clinging
detection sensor
1st drawer transport sensor
Fuser transport sensor
Reverse path sensor
Duplexing unit path exit sensor
Duplexing unit path entrance
sensor
Bypass feed sensor
4th drawer transport sensor
3rd drawer/tandem LCF transport
sensor
2nd drawer transport sensor
Option LCF feed sensor
Bridge unit path exit sensor
Bridge unit path entrance sensor
Reverse sensor
Reverse section stationary jam
detection sensor
Upper paper exit sensor
Lower paper exit sensor
Reverse section paper transport
detection sensor
Sensors in the finisher
6 - 45
Test Mode/Input check
03-[ALL]OFF/[4]/[B]
03-[COPY]ON/[5]/[H]
03-[ALL]OFF/[9]/[C]
03-[ALL]OFF/[9]/[D]
03-[SCAN]ON/[1]/[D]
03-[ALL]OFF/[2]/[C]
03-[COPY]ON/[5]/[F]
03-[ALL]OFF/[1]/[C]
03-[SCAN]ON/[3]/[E]
03-[SCAN]ON/[3]/[G]
03-[SCAN]ON/[3]/[H]
03-[SCAN]ON/[3]/[A]
03-[SCAN]ON/[1]/[A]
03-[SCAN]ON/[1]/[B]
03-[SCAN]ON/[1]/[C]
03-[SCAN]ON/[5]/[E]
03-[ALL]OFF/[1]/[A]
03-[SCAN]ON/[3]/[C]
03-[ALL]OFF/[1]/[B]
03-[SCAN]ON/[3]/[D]
03-[SCAN]ON/[3]/[F]
03-[SCAN]ON/[4]/[A]
03-[ALL]OFF/[1]/[E]
03-[COPY]ON/[7]/[A]
03-[ALL]OFF/[4]/[C]
03-[COPY]ON/[5]/[G]
03-[COPY]ON/[8]/[F]
-
e-STUDIO5520C/6520C/6530C
ERROR CODE and TROUBLESHOOTING
6