Toshiba e-STUDIO6520C Service Handbook page 220

[E-3] Adjustment for medium-sized paper (Length: 220 mm to 329 mm)
While pressing [0] and [5] simultaneously, turn the power ON. → (Adjustment Mode)
(1)
Press [3] → [FAX]. (A grid pattern with 10 mm squares is printed out. Use A4-R/LT-R from the 1st
(2)
drawer.)
(3) Check the grid pattern on the test print and measure the distance E from the left edge of the
paper to the 6th line of the grid pattern.
(4) Check if the distance E is within 52±0.5 mm.
(5) If not, use the following procedure to change values and measure the distance E again.
<Procedure>
(Adjustment Mode) → (Key in the code [498]) → [START] → [2] → [START]
→ (Key in a value (acceptable values: 0 to 255))
→ [ENTER] or [INTERRUPT] (Stored in memory)
→ "100% A" is displayed
→ Press [3] → [FAX] → (A grid pattern is printed out.)
* The larger the adjustment value is, the longer the distance E becomes (approx. 0.04 mm/
step).
Note:
When the laser writing start position (05-498-0) for long-sized paper is changed, the one for
medium-sized paper is also altered. (However, the value of 05-498-2 is not changed.)
If 05-498-0 is changed, check it with A4-R/LT-R paper and adjust the value of 05-498-2 again as
required.
<Adjustment procedure summarization for A to E>
[0] [5] [Power ON] → [98] ([3] (05-445, 498) for duplexing) → [FAX]
A: 05-4772 (2nd drawer, A3/LD)
B: 05-411 (2nd drawer, A3/LD)
05-497-0 (1st drawer, A4/LT)
05-497-1 (2nd drawer, A3/LD)
05-497-2 (3rd drawer, A4/LT)
05-497-3 (4th drawer, A4/LT)
05-497-4 (2nd drawer, A4/LT)
05-497-5 (Bypass feed, A4/LT)
05-497-6 (2nd drawer, A4/LT)
C: 05-487-0 to 11 (2nd drawer, A3/LD)
D: 05-408 (2nd drawer, A3/LD)
05-440 (1st drawer, A4/LT)
05-441 (2nd drawer, A3/LD)
05-444 (3rd drawer, A4/LT)
05-428 (4th drawer, A4/LT)
05-442 (Bypass feed, A4/LT)
05-445 (Duplex feeding, A3/LD)
05-429 (2nd drawer, A4/LT)
05-443 (2nd drawer, A4/LT)
E: 05-498-0 (2nd drawer, A3/LD),
05-498-1 (1st drawer, A4/LT)
05-498-2 (A4-R/LT-R)
e-STUDIO5520C/6520C/6530C
ADJUSTMENT
→ 200±0.5 mm (0.1 mm/step)
→ 52±0.5 mm (0.04 mm/step)
→ 200±0.5 mm (0.1 mm/step)
→ 52±0.5 mm (0.10 mm/step)
→ 52±0.5 mm (0.10 mm/step)
→ 52±0.5 mm (0.10 mm/step)
→ 52±0.5 mm (0.04 mm/step)
© 2008-2011 TOSHIBA TEC CORPORATION All rights reserved
3 - 22