Toshiba e-STUDIO6520C Service Handbook page 397

Error code Classification
CB82 Finisher related
service call
CB83
CB84
CB91
CB92
CB93
CB94
CB95
CBA0
CBB0
CBC0
CBE0
CC20
CC30
CC31
CC41
CC51
CC52
CC60
CC61
CC71
CC72
CC73
CC74
© 2008-2011 TOSHIBA TEC CORPORATION All rights reserved
Contents
Finisher - Main CPU program error
Saddle Stitch Finisher - Main CPU program error
Hole Punch Unit - Main CPU program error
Saddle Stitch Finisher flash ROM abnormality
Saddle Stitch Finisher RAM abnormality
Additional folding motor abnormality
Saddle transport motor abnormality
Stacker motor abnormality
Stitch motor (front) abnormality: Stitch motor (front)
is not rotating or rotary cam is not moving normally.
[MJ-1103/1104]
Stitch motor (rear) abnormality: Stitch motor (rear)
is not rotating or rotary cam is not moving normally.
[MJ-1103/1104]
Alignment motor abnormality: Alignment motor is
not rotating or aligning plate is not moving normally.
[MJ-1103/1104]
Paper folding motor abnormality: Paper folding
motor or paper folding roller is not rotating normally.
[MJ-1103/1104]
Communication error between finisher and saddle
stitcher: Communication error between finisher
controller PC board and saddle stitcher controller
board [MJ-1103/1104]
Stack transport motor abnormality: The stack
transport motor is not rotating or the stack transport
belt is not moving normally. [MJ-1103/1104]
Transport motor abnormality: The transport motor is
not rotating or the stack transport roller -1 and -2 is
not rotating normally. [MJ-1103/1104]
Paper holder cam home position abnormality: The
paper holder cam is not at the home position. [MJ-
1103/1104]
Sideways adjustment motor (M2) abnormality:
Sideways adjustment motor is not rotating or
puncher is not shifting normally. [MJ-1103/1104
(when MJ-6102 is installed)]
Skew adjustment motor (M1) abnormality: Skew
adjustment motor is not rotating or puncher is not
shifting normally. [MJ-1103/1104 (when MJ-6102 is
installed)]
Punch motor abnormality: Punch motor is not
rotating or puncher is not shifting normally. [MJ-
1103/1104 (when MJ-6102 is installed)]
Punch motor (M3) home position detection error:
Punch motor is not rotating or puncher is not
shifting normally. [MJ-1103/1104 (when MJ-6102 is
installed)]
Punch ROM checksum error: Abnormality of
checksum value on Hole punch controller PC board
is detected when the power is turned on. [MJ-1103/
1104 (when MJ-6102 is installed)]
Punch RAM read/write error: Abnormality of
checksum value on Hole punch controller PC board
is detected when the power is turned on. [MJ-1103/
1104 (when MJ-6102 is installed)]
Punching device power supply abnormality
Punch unit transport pulse abnormality
6 - 15
Troubleshooting
P. 6-98
P. 6-98
P. 6-98
P. 6-98
P. 6-98
P. 6-99
P. 6-99
P. 6-99
P. 6-100
P. 6-100
P. 6-100
P. 6-100
P. 6-100
P. 6-101
P. 6-101
P. 6-101
P. 6-102
P. 6-102
P. 6-103
P. 6-103
P. 6-103
P. 6-103
P. 6-103
P. 6-103
e-STUDIO5520C/6520C/6530C
ERROR CODE and TROUBLESHOOTING
6