Page 1
SERVICE HANDBOOK MULTIFUNCTIONAL DIGITAL COLOR SYSTEMS e-STUDIO5520C/6520C/6530C Model: FC-5520C/6520C/6530C Publish Date: August 2008 File No. SHE070005J0 R070921E4900-TTEC Ver10_2011_11...
Page 3
GENERAL PRECAUTIONS REGARDING THE SERVICE FOR e-STUDIO5520C/6520C/6530C The installation and service should be done by a qualified service technician. 1. Transportation/Installation When transporting/installing the equipment, employ four persons and be sure to move it by the casters while lifting the stoppers. The equipment is quite heavy and weighs approximately 245 kg (540.12 lb) or 246 kg (542.33 lb), therefore pay full attention when handling it.
Page 4
Be sure to handle/install them properly. If these parts are short-circuited and their functions become ineffective, they may result in fatal accidents such as burnout. Do not allow a short-circuit or do not use the parts not recommended by Toshiba TEC Corporation.
Page 5
4. Cautionary Labels During servicing, be sure to check the rating plate and cautionary labels such as “Unplug the power cable during service”, “CAUTION. HOT”, “CAUTION. HIGH VOLTAGE”, “CAUTION. LASER BEAM”, etc. to see if there is any dirt on their surface and if they are properly stuck to the equipment.
Page 6
5. Disposal of the Equipment, Supplies, Packing Materials, Used Batteries and IC-RAMs Regarding the recovery and disposal of the equipment, supplies, packing materials, used batter- ies and IC-RAMs including lithium batteries, follow the relevant local regulations or rules. 6. When the option has been installed: When the EFI printer board has been installed, be sure to unplug the power cable before performing maintenance and inspection, otherwise troubles such as a communication error may occur.
Precautions for Transporting Equipment Once Unpacked 1 General Description It is recommended to follow the procedure below when you transport equipment that has already been unpacked but has not been packed again. Note that the following procedure cannot guarantee the operation of the transported equipment. Item Content Gasket in Reversing Automatic...
Page 8
2 Precautions and Procedures for Transporting Equipment Checking gaskets in the RADF The installation of gaskets to the RADF, which is described in the Unpacking Instructions, must not be performed when the equipment is unpacked but must be when it is reinstalled at a user’s office. Do not install the gaskets in the equipment before transporting it because if it is transported with the gaskets installed, the screws fixing the scanner may contact with the gaskets and thus damage them.
Page 9
Notes: • The installation of materials for covering the holes of the scanner fixing screws (e.g. rubber cap, blind seal), which is described in the Unpacking Instructions, must not be performed when the equipment is unpacked but must be when it is reinstalled at a user's office. •...
Page 10
Installing a drum protection sheet 1. Pull out the EPU tray. 2. Install a drum protection sheet on the K drum. 3. Push the EPU tray in, and then reassemble the equipment in the procedure reverse to disas- sembly. Notes: •...
Page 11
Installing the sealing material in toner supply opening 1. Open the front cover and then take off the toner cartridges (Y, M, C and K). Note: The toner cartridges must not be installed while the equipment is being transported. Pack them separately from the equipment.
Page 13
ALLEGEMEINE SICHERHEITSMASSNAHMEN IN BEZUG AUF DIE WARTUNG FÜR e-STUDIO5520C/6520C/6530C Die Installation und die Wartung sind von einem qualifizierten Service- Techniker durchzuführen. 1. Transport/Installation Zum Transportieren/Installieren des Gerätes werden 4 Personen benötigt. Bewegen Sie es mit den Rollen, während Sie die Absperrvorrichtungen heben. Das Gerät ist sehr schwer und wiegt etwa 245 kg oder 246 kg;...
Page 14
Sie müssen unbedingt korrekt gehandhabt und installiert werden. Wenn diese Teile kurzgeschlossen und funktionsunfähig werden, kann dies zu schwerwiegenden Schäden, wie einem Abbrand, führen. Kurzschlüsse sind zu vermeiden, und es sind ausschließlich Teile zu verwenden, die von der Toshiba TEC Corporation empfohlen sind.
Page 15
4. Warnetiketten Im Rahmen der Wartung unbedingt das Leistungsschild und die Etiketten mit Warnhinweisen überprüfen, um sicherzustellen, dass sie nicht verschmutzt sind und korrekt am Gerät angebracht sind. 1) Erkennungsetikett 2) Erklärungsetikett 3) Klassifizierungsetikett 4) Warnung für Erdungskabel 5) Warnung für Bereiche mit höhen Temperaturen (Duplexeinheit / Fixiereinheit) 6) Warnung für Bereiche mit höhen Temperaturen (Fixiereinheit) 7) Warnung für Bereiche mit höhen Temperaturen (Brückeneinheit) 5.
Page 16
Caution: Dispose of used batteries and IC-RAMs including lithium batteries according to this manual. Attention: Se débarrasser de batteries et IC-RAMs usés y compris les batteries en lithium selon ce manuel. Vorsicht: Entsorgung der gebrauchten Batterien und IC-RAMs (inclusive der Lithium-Batterie) nach diesem Handbuch.
Page 17
• Laseremissionseinheit Diese Einheit besteht aus der Laserdiode, dem Fokussierungsobjektiv, der Blende und dem Zylinderobjektiv. Laserdiode Diese Laserdiode zeichnet sich durch eine geringe Regeldifferenz, eine kleine Laservariation und einen niedrigen Schwellenstrom aus. Die Blende der Laseremissionseinheit ist unter dem Fokussierobjektiv angeordnet, um die Form der Laserstrahlen in der primären und sekundären Scanrichtung festzulegen.
2. The value in the “Replacement” field of the table below indicates the replacement number of output pages in either the black or the full color mode. If they differ according to the model, they are indicated in the order of the e-STUDIO5520C, e-STUDIO6520C and e- STUDIO65300C.