Page 1 File No. SME160004A0 R160521P3001-TTEC Ver01_F 2017_09...
Page 2 , NetWare and NDS are trademarks of Novell, Inc. • e-STUDIO, e-BRIDGE, and TopAccess are trademarks of Toshiba Tec Corporation. • Other company names and product names in this manual are the trademarks of their respective companies. © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved Under the copyright laws, this manual cannot be reproduced in any form without prior written permission of TOSHIBA TEC CORPORATION.
Page 3 GENERAL PRECAUTIONS REGARDING THE SERVICE The installation and service shall be done by a qualified service technician. 1. Transportation/Installation - When transporting/installing the equipment, employ two or more persons and be sure to move it by the casters while lifting the stoppers. The equipment is quite heavy and weighs approximately Approx.
Page 4 If these parts are short-circuited and their functions become ineffective, they may result in fatal accidents such as explosion or burnout. Avoid short-circuiting and do not use parts not recommended by Toshiba TEC Corporation. 5. Cautionary Labels During servicing, be sure to check the rating plate and cautionary labels to see if there is any dirt on...
Page 5 6. Disposal of the Equipment, Supplies, Packing Materials, Used Batteries and IC-RAMs - Regarding the recovery and disposal of the equipment, supplies, packing materials, used batteries and IC-RAMs including lithium batteries, follow the relevant local regulations or rules. Caution: Dispose of used batteries and IC-RAMs including lithium batteries according to this manual. Attention: Se débarrasser de batteries et IC-RAMs usés y compris les batteries en lithium selon ce manuel.
Page 6 ALLGEMEINE SICHERHEITSMASSNAHMEN IN BEZUG AUF DIE WARTUNG Die Installation und die Wartung sind von einem qualifizierten Service- Techniker durchzuführen. 1. Transport/Installation - Zum Transportieren/Installieren des Gerätes werden 2 Personen benötigt. Bewegen Sie es mit den Rollen, während Sie die Absperrvorrichtungen heben. Das Gerät ist sehr schwer und wiegt etwa 213 kg; deshalb muss bei der Handhabung des Geräts besonders aufgepasst werden - Beim Transportieren des Geräts nicht an den beweglichen Teilen oder Einheiten (z.B.
Page 7 Wenn diese Teile kurzgeschlossen und funktionsunfähig werden, kann dies zu schwerwiegenden Schäden, wie einer Explosion oder einem Abbrand, führen. Kurzschlüsse sind zu vermeiden, und es sind ausschließlich Teile zu verwenden, die von der Toshiba TEC Corporation empfohlen sind. 5. Warnetiketten - Im Rahmen der Wartung unbedingt das Leistungsschild und die Etiketten mit Warnhinweisen überprüfen, um sicherzustellen, dass sie nicht verschmutzt sind und korrekt am Gerät angebracht...
Page 8 6. Entsorgung des Geräts, der Verbrauchs- und Verpackungsmaterialien, alter Akkus und IC-RAMs - In Bezug auf die Entsorgung und Wiederverwertung des Geräts, der Verbrauchs- und Verpackungsmaterialien, alter Akkus und IC-RAMs, einschließlich Lithiumakkus, sind die einschlägigen nationalen oder regionalen Vorschriften zu befolgen. Caution: Dispose of used batteries and IC-RAMs including lithium batteries according to this manual.
Page 9 Revision Record Ver00 <2013.04.25> Page Contents Initial release Ver01 <2017.09.29> Page Contents The mistake has been corrected. The mistake has been corrected. 1-11 to 1-14 The mistake has been corrected. 1-17 to 1-18 The mistake has been corrected. 1-21 The mistake has been corrected. 1-26 The mistake has been corrected.
Page 11 In addition, this manual is expected to facilitate the marketing of Toshiba MFPs to prospective customers that have a specific demand for image quality and the expansion of sales.
Page 12 Purpose of the Imaging Manual Icons The following icons used in this manual denote the following: : • Copy ——— An adjustment having an effect on copying in the Black mode (excluding the Image smoothing mode) • Printer ——– An adjustment having an effect on Black and White mode printing * The adjustment will be effective, if "Black and White"...
Page 13: Table Of Contents
To Obtain Image in Even Density Level ............2-81 2.22 To Improve Reproducibility of Red Seal Color ..........2-83 2.23 To Reduce Streaks at Scanning with DF ............ 2-84 e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 14 3.25.4 To Print Using Custom RGB Profiles ............3-130 3.25.5 To Convert Colors with Specified Source ICC Profiles (Not Using Embedded ICC Profiles) ......................3-133 3.25.6 To Perform Further Adjustment After Using ICC Profiles ......3-137 e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 15 "Custom" selected) ................5-18 To Eliminate Shading around Scanned Images .......... 5-20 5.10 To Scan Yellow Clearly ................5-21 5.11 To Reduce Streaks in Scanning with DF ............ 5-23 e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 17: General Adjustments - Copying, Printing And E-Filing (Output From Box)
But "USER" can also be selected to allow the user to operate it. Refer to the MFP Management Guide for further information regarding how to select the "CALIBRATION DISPLAY LEVEL" option. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 1 - 1...
Page 18 After performing automatic calibration, print and check the image quality. If further image quality adjustments are necessary, go to step (2) to adjust the transfer (2nd transfer) roller bias output. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 1 - 2...
Page 19 (d) The message “Set Auto Calibration Yes or No.” appears. Press [Yes]. After performing simple calibration, print the image and check its quality. If further image quality adjustments are necessary, carry out the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 1 - 3...
Page 20 * "Front" refers to the printed side in the simplex mode or the side that is delivered facing upwards in the duplex mode. "Back" refers to the printed side that is delivered facing downwards in the duplex mode. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 1 - 4...
Page 21 (for codes 05-2934 to 2937) to the default (set value: 5) and then perform the adjustment again. • When replacing any consumable, refer to the relevant information in the Service Manual. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 1 - 5...
Page 22: To Adjust The Density On A Solid Colored Image
*When the value becomes larger than the present one, and the solid image becomes darker. When it becomes smaller, the image becomes lighter. The value must fall within a range of -50 and +50 from the default. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 1 - 6...
Page 23 * The table below shows you the acceptable paper weight for the paper type. Paper type Acceptable paper weight Plain/Recycled 60 to 80 g/m² Max. 60 lb. Cover Thick 81 to 105 g/m² Max. 110 lb. Index e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 1 - 7...
Page 24 • The effects of adjustment may vary, depending on the usage pattern of the consumables, such as the developer material and drum, and the installation environment of the MFP. • When replacing any consumables, refer to the relevant information in the Service Manual. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 1 - 8...
Page 25 Be sure to reset the counter. Otherwise, it may cause a loss in performance, including degradation in the image quality and a reduction in the life of the consumables. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 1 - 9...
Page 26 • The effect of the adjustment may vary, depending on the usage pattern of the consumables, such as the developer material and drum, and the installation environment of the MFP. • When replacing any consumable, refer to the relevant information in the Service Manual. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 1 - 10...
Page 27: To Achieve The Image Quality Most Suitable For The Paper Used (To Eliminate Blur And Graininess From An Image)
Set the value within a range of "2" to "8" to optimize the halftones. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 1 - 11...
Page 28 * "Front" refers to the printed side in the simplex mode or the side that is delivered facing downwards in the duplex mode. "Back" refers to the printed side that is delivered facing upwards in the duplex mode. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 1 - 12...
Page 29 After performing the adjustment, print and check the image quality. If further image quality adjustment is necessary, go to step (3). (2) If the image on the high-density area looks grained on plain paper other than the TOSHIBA-recommended one is used, select "recycled paper" as a paper type.
Page 30 After setting the value, print and check the image quality. If further image quality adjustment is necessary, go to step (3). e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 1 - 14...
Page 31 [2934] to [2937] (bias offset) and [5293] to [5294] (fusing temperature during printing) back to the default ones. Then perform the adjustment again. • When replacing any consumable, refer to the relevant information in the Service Manual. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 1 - 15...
Page 32: To Minimize Variations In The Image Quality Under The Operating Conditions (To Optimally Program Image Quality Control)
The image contrast varies, depending on the The image quality is constantly maintained. date and time when copying or printing is performed or the type of job. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 1 - 16...
Page 33 *1. The correction accuracy is high but it takes approx. 90 seconds (equal to the time taken by existing models). This control is performed with a simple calibration operated from the control panel. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 1 - 17...
Page 34 Then a copy or print job will be performed. Value for 08-2505 Difference in relative humidity 5%R.H. 10%R.H. (default) e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 1 - 18...
Page 35 120 minutes or longer 150 minutes or longer 180 minutes or longer 240 minutes or longer 300 minutes or longer 360 minutes or longer (default value) e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 1 - 19...
Page 37 ・Changing this setting improves the stability of the image quality. However, a long application of this change affects the life of consumables. It is recommended to make only a minimal change and then return to the default value immediately. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 1 - 21...
Page 38 * After replacing any consumable, remember to reset the counter corresponding to it to “0.” Otherwise, it may cause a loss in MFP performance, including degradation in the image quality and a reduction in the life of the consumables. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 1 - 22...
Page 39 Otherwise, it may cause a loss in MFP performance, including slowdown in the copying or printing speed. • When replacing any consumable, refer to the relevant information in the Service Manual. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 1 - 23...
Page 40: To Correct Out-Of-Registration Colors
(2) Load the thick papers in the drawer. (Paper weight: 106 to 256 g/m² / 29 to 80 lbs (Cover) / 90 to 140 lbs (Index)) (3) Select the paper type of the thick paper loaded in the drawer. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 1 - 24...
Page 41 Paper feeding speed faster than transfer belt Page number rotating speed Paper feeding direction Black belt at the leading edge in the paper feeding direction e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 1 - 25...
Page 42 (b) Select code [104], and then press [TEST PRINT]. Check all the patches on the second page of the printed test print pattern to check whether the misaligned colors have been improved. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 1 - 26...
Page 43 • Out-of-registration colors cannot always be perfectly corrected; this depends on the type of text or lines to print. • Also, refer to the relevant information in the Service Manual for further information regarding color registration control procedures. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 1 - 27...
Page 44: To Adjust Printing Positions On Front And Back Sides In The Duplex Mode
[F] Secondary scanning data writing start 52 ± 0.5 mm 4.2 ± 0.5 mm position at duplexing * Use this chart to adjust the void width match. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 1 - 28...
Page 45 (4) Press [OK] to store the value. → The equipment goes back to the ready state. (5) Check the chart. If the image is not in the desired reproduction ratio, repeat steps (2) to (4). e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 1 - 29...
Page 47: Copier-Specific Adjustments
* The procedure to use varies, depending on whether to adjust the copy image quality in the Black mode, Full color mode. Refer to the procedure corresponding to the particular user’s request. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 48: To Adjust The Copy Image Quality In The Black Mode
After increasing the sharpness intensity, copy and check the copy image quality. With the sharpness intensity set to the maximum, if further image quality adjustments are still necessary, the service technician must use the following procedures. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 49 "-3" to "-4". After selecting the Text mode, copy and check the copy image quality. If further image quality adjustments are still necessary, use the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 50 But it will not affect the light text or graphic images. Therefore, never change the value for the low- density area. Subcode Area where the density is adjusted Medium-density area High-density area e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 51 K toner used compared with that for the other colors, or it may create a difference in the reproducibility of halftones. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 52: To Adjust The Copy Image Quality In The Full Color Mode
One step in the indicator corresponds to “20” of the setting value in [05] code. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 53 [05] code is “103” (-25 from the default value), the limit of the steps in the soft side of the indicator is “-3”. If the step is set at “-4”, the image quality will not be changed. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 54 * For the User custom mode, refer to “2.18 To Program Frequently Used Copy Settings (To Use Custom Mode)”. * The setting content of the default value “0” is the same as that for the value “5”. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 55 After changing the value, make a copy and check the image quality. If further image quality adjustments are necessary, reset all the values changed in steps (1) to (6) above to the default one and then follow the next step. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 57: To Closely Match The Color Balance Of The Original
Then use other procedures. * Both the service technician and the user can use procedures (1) to (3). * Only the service technician must use procedure (4) and (5). e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-11...
Page 58 Black and White mode simultaneously. After performing automatic calibration, copy and check the copy image quality. If further image quality adjustments are still necessary, use the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-12...
Page 59 (d) Press [ENTER]. After adjusting the tint of the colors, copy and check the copy image quality. If further image quality adjustments are still necessary, use the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-13...
Page 60 Setting a larger value: The tint of Magenta becomes closer to For adjusting the tint of that of R (Red). Magenta Setting a smaller value The tint of Magenta becomes closer to that of B (Blue). e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-14...
Page 61 Enter a value within the recommended value range mentioned in the procedures. Otherwise, it may cause a loss in MFP performance, including degradation in the image quality and a reduction in the life of the consumables. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-15...
Page 62: To Improve The Reproducibility Of Gray
[CALIBRATION DISPLAY LEVEL] option. After performing automatic calibration, copy and check the copy image quality. If further image quality adjustments are still necessary, use the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-16...
Page 63 * The subcode varies according to the area where the density is adjusted. Refer to the table below and set the subcode for the area to be adjusted. Subcode Area where the density is adjusted Low-density area Medium-density area High-density area e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-17...
Page 64 Enter a value within the recommended value range mentioned in the procedures. Otherwise, it may cause a loss in MFP performance, including degradation in the image quality and a reduction in the life of the consumables. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-18...
Page 65: To Copy In Vivid Colors
* Only the service technician must use procedure (4) and (5). * Only if the vividness of R (Red) is still insufficient even after procedures (1) to (4) have been used, the service technician must use procedure (6). e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-19...
Page 66 * The sub code varies according to the area where the hue is adjusted. Set the sub code for the area to be adjusted by referring to the following below. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-20...
Page 67 * The value for the code corresponding to the original mode (Text/Photo, Text, or Printed image) will affect the copy image quality in the Full color mode and the Auto color mode. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-21...
Page 68 Therefore, perform the adjustment, being aware that the image quality of all future printouts will be changed, when printing out originals other than the one that is used for the adjustment. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-22...
Page 69 Enter a value within the recommended value range mentioned in the procedures. Otherwise, it may cause a loss in MFP performance, including degradation in the image quality and a reduction in the life of the consumables. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-23...
Page 70: To Make The Pale Area Of The Original Look Darker And Sharper (To Improve The Highlight Reproducibility)
After increasing the background density, copy and check the copy image quality. With the background density set to the maximum, if further image quality adjustments are still necessary, the service technician must use the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-24...
Page 71 [7690] to change the reproduction level of the background. * For the User custom mode, refer to the procedures in “2.18.2 To Adjust Custom Mode Settings in Full Color Mode”. [05] Code Setting value 05-7690 e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-25...
Page 72 Setting “2” for subcode allows you to adjust the high-density area. But it will not affect the highlighted area. Therefore, never change the value for the high-density area. Subcode Area where the density is adjusted Low-density area Medium-density area e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-26...
Page 73 Enter a value within the recommended value range mentioned in the procedures. Otherwise, it may cause a loss in MFP performance, including degradation in the image quality and a reduction in the life of the consumables. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-27...
Page 74: To Eliminate The Background Color
* The procedure to use varies, depending on whether to adjust the copy image quality in the Black mode or the Full color mode. Refer to the procedure corresponding to the user’s particular request. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-28...
Page 75: To Adjust The Copy Image Quality In The Black Mode
* The subcode varies according to the area where the density is adjusted. Refer to the table below and set the subcode for the area to be adjusted. The background density will vary, if the low- or medium-density area e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-29...
Page 76  Remarks Enter a value within the recommended value range mentioned in the procedures. Otherwise, it may cause a loss in MFP performance, including degradation in the image quality. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-30...
Page 77: To Adjust The Copy Image Quality In The Full Color Mode
After adjusting the background density, copy and check the copy image quality. If further image quality adjustments are still necessary, or background elimination is necessary according to color, use the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-31...
Page 78 Low-density area Medium-density area After adjusting the background density, copy and check the copy image quality. If further image quality adjustments are still necessary, use the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-32...
Page 79  Remarks Enter a value within the recommended value range mentioned in the procedures. Otherwise, it may cause a loss in MFP performance, including degradation in the image quality. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-33...
Page 80: To Avoid Copying The Image Seen Through The Back Of A Page Printed On Thin Paper
* The procedure to use varies, depending on whether to adjust the copy image quality in the Black mode or the Full color mode. Refer to the procedure corresponding to the user’s particular request. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-34...
Page 81: To Adjust The Copy Image Quality In The Black Mode
"25" for the [05] code corresponds to one step in the background adjustment on the control panel. After adjusting the background density, copy and check the copy image quality. If further image quality adjustments are still necessary, use the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-35...
Page 82 Enter a value within the recommended value range mentioned in the procedures. Otherwise, it may cause a loss in MFP performance, including degradation in the image quality and a reduction in the life of the consumables. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-36...
Page 83: To Adjust The Copy Image Quality In The Full Color Mode
If the density of the background color is decreased, the highlighted area may become less visible. After adjusting the background density, copy and check the copy image quality. If further image quality adjustments are still necessary, use the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-37...
Page 84  Remarks Enter a value within the recommended value range mentioned in the procedures. Otherwise, it may cause a loss in MFP performance, including degradation in the image quality. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-38...
Page 85: To Eliminate Moiré
Then use other procedures. * Both the service technician and the user can use procedures (1) and (2). * Only the service technician must use procedure (3). e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-39...
Page 86 Chapter 2.18. After changing the default original mode option, copy and check the copy image quality. If further image quality adjustments are still necessary, use the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-40...
Page 87 [05] code is “103” (-25 from the default value), the limit of the steps in the soft side of the indicator is “-3”. If the step is set at “-4”, the image quality will not be changed. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-41...
Page 88 • Enter a value within the recommended value range mentioned in the procedures. Otherwise, it may cause a loss in MFP performance, including degradation in the image quality. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-42...
Page 89: To Copy Sharply (To Enhance Sharpness)
Press [SHARP] to increase the sharpness intensity. After increasing the sharpness intensity, copy and check the copy image quality. If further image quality adjustment is necessary, go to the next step. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-43...
Page 90 Setting value "153": +100 +100 Since "+25" is assigned to the center, the image quality remains the same even if the indicator is changed from "+3" to "+4". e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-44...
Page 91 • Enter a value within the recommended value range mentioned in the procedures. Otherwise, it may cause a loss in copier performance, including degradation in the image quality. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-45...
Page 92: To Make Photo Edges Look Softer
Then use other procedures. * Both the service technician and the user can use procedures (1) and (2). * Only the service technician must use procedures (3) to (5). e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-46...
Page 93 05-7797 Printed image 05-7798 Set a value smaller Full color Photo 05-7799 than 128. 0 to 255 (28 to 127) 05-7800 User custom 05-7795 Red seal color 05-7794 e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-47...
Page 94 After decreasing the sharpness intensity, copy and check the copy image quality. If further image quality adjustments are still necessary, use the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-48...
Page 95 * Remember that if a value larger than “5” is set, the edges of the image are enhanced (attaching importance to the reproducibility of text). The table below shows you the correlation between the value and image quality. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-49...
Page 96  Remarks Enter a value within the recommended value range mentioned in the procedures. Otherwise, it may cause a loss in MFP performance, including degradation in the image quality. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-50...
Page 97: To Make Solid Filled Bold Text (Logo) Highly Colored
* The procedure to use varies, depending on whether to adjust the copy image quality of a black or colored logo. Refer to the procedure corresponding to the user’s particular request. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-51...
Page 98: To Adjust The Copy Image Quality Of A Black Logo
After adjusting the tint of black, copy and check the copy image quality. If further image quality adjustment is necessary even after the tint of black was set to the maximum, the service technician must perform the next step. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-52...
Page 99 The adjustment may possibly cause the highly or deeply colored area, such as in a photo, to become blurred on the copy. Also, it may also cause offset failure, grained images and degradation in gradation. Therefore, carefully perform the adjustment, while checking the copy image. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-53...
Page 100: To Adjust The Copy Image Quality Of A Colored Logo
After selecting the Text or Map mode, copy and check the copy image quality. If further image quality adjustments are still necessary, the service technician must use the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-54...
Page 101 The adjustment may possibly cause a dark-colored area, such as in a photo, to become blurred on the copy. Also, it may also cause offset failure, grained images and degradation in gradation. Therefore, carefully perform the adjustment, while checking the copy image. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-55...
Page 102: To Sharply Contrast The Hues Of Highlighters On The Copy
To reproduce the hues of similar highlighters, such as yellow and green, while producing sharp contrasts on the copy, perform color adjustment (color balance adjustment or RGB adjustment). e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-56...
Page 103 R (Red). Then the tint of the red will be closely matched with that of M (Magenta). After adjusting the hue, copy and check the copy image quality. If further image quality adjustments are still necessary, use the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-57...
Page 104 * The subcode varies according to the area where the density is adjusted. Refer to the table below and set the subcode for the area to be adjusted. Subcode Area where the density is adjusted Low-density area Medium-density area High-density area e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-58...
Page 105  Remarks Enter a value within the recommended value range mentioned in the procedures. Otherwise, it may cause a loss in MFP performance, including degradation in the image quality. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-59...
Page 106: To Obtain A Good Color Balance On Thick Paper
Then use other procedures. * Only the service technician must use procedures (1), (2) and (4). * Both the service technician and the user can use procedure (3). e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-60...
Page 107 * Although the larger the value, the darker the density becomes, offsetting may occur if the value is too large. Adjust the value while checking the copy image carefully. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-61...
Page 108 Red seal color 05-7986 0/1/2 Text/Photo 05-7975 0/1/2 Text 05-7976 0/1/2 Printed image 05-7977 0/1/2 Photo 05-7978 0/1/2 (Black) 05-7979 0/1/2 User custom 05-7983 0/1/2 Red seal color 05-7987 0/1/2 e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-62...
Page 109 MFP performance, including degradation in the image quality and a reduction in the life of the consumables • If the adjustment causes a toner fixing problem, decrease the values for codes 05-7905 to 7911. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-63...
Page 110: To Obtain Smooth Gray-Scale Photo Images
* To have “IMAGE SMOOTHING” selected from among the original mode options by default, refer to 2.18 To Program Frequently Used Copy Settings (To Use Custom Mode).  Caution after the adjustment Nothing in particular. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-64...
Page 111: To Change The Threshold In Auto Color Mode (To Change The Threshold Between The Full Color Mode And The Black Mode To Meet The User's Needs)
Then it will be copied in the Full color mode or the Black mode. But adjust the threshold value, in order to change the threshold between the Black mode and the Full color mode and suit the preferences of the user. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-65...
Page 112 After specifying the original size and copy size, copy and check the copy image quality. If further image quality adjustments are still necessary, the service technician must use the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-66...
Page 113 Therefore, carefully perform the adjustment, while checking whether any type of original is correctly detected. • Note that changing the judgment threshold for originals influences the Auto color in network scanning. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-67...
Page 114: To Adjust The Twin-Color Copy Image Quality
Red and black mode, or the boundary between black and colors other than black. Refer to the procedure corresponding to the user’s particular request. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-68...
Page 115: To Adjust The Tint Of Colors Other Than Black
* Press [DETAIL]. The tint of the color can be adjusted according to the density area (low-, medium- or high-density area).  Caution after the adjustment Nothing in particular. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-69...
Page 116: To Adjust The Boundary Between Black And Colors Other Than Black
Subcode Area where the density is adjusted High-density area Medium-density area Low-density area  Caution after the adjustment Nothing in particular. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-70...
Page 117: To Adjust The Tint Of Specified Colors For Twin-Color Or Single-Color Copying
Magenta 7644 0 to 255 Yellow 7645 0 to 255 Yellow green 7646 0 to 255 Cyan 7647 0 to 255 Pink 7648 0 to 255 e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-71...
Page 118 2. Copier-specific Adjustments 7649 0 to 255 Orange 7650 0 to 255 Green 7651 0 to 255 Blue 7652 0 to 255 Purple 7653 0 to 255 e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-72...
Page 119: To Adjust The Image Quality Scanned From The Df
*Correctly adjusting the installation heights of the MFP and the DF is a prerequisite to perform this adjustment. Therefore, perform all the necessary adjustments. Only if further adjustment is still desired for the reproducibility of background, should this adjustment be performed. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-73...
Page 120 Darker background is reproduced than the one obtained when “3” is Dark set. After setting the value, copy and check the image quality. If further image quality adjustment is necessary, go to the next step. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-74...
Page 121 Correctly adjusting the installation heights of the MFP and the DF is a prerequisite to perform this adjustment. Therefore, perform all the necessary adjustments. Only if further adjustment is still desired for the reproducibility of background, should this adjustment be performed. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-75...
Page 122: To Program Frequently Used Copy Settings (To Use Custom Mode)
Custom mode for black mode Unused Used (Text/Photo base) Used (Text base) After the setting, perform the adjustment accordingly referring to the corresponding chapters.  Cautions after the adjustment Nothing in particular e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-76...
Page 123: To Adjust Custom Mode Settings In Full Color Mode
* The default adjustment value for the custom mode is preset at the one that reproduces the image quality equivalent to that of Text/Photo in the full color mode at the time of shipment. After the setting, perform the adjustment accordingly referring to the corresponding chapters. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-77...
Page 124: To Copy While Erasing Shadow Outside Of Image
Also the area to be erased may change depending on the orientation of the original. Therefore adjust it carefully while checking the copy image. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-78...
Page 125: To Avoid Copying Blank Page Of Original Scanned With Df
After the setting, copy and check the image. If there is any page other than colored pages that cannot be omitted, the service technician must perform the procedure below. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-79...
Page 126 • Originals with a small portion of small letters may be judged as a blank page. Therefore adjust the value carefully while checking the copy image. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-80...
Page 127: To Obtain Image In Even Density Level
] to lower the copy density manually. After the adjustment is complete, make a copy and confirm the image quality. If uneven image density still persists, have the service technicians perform the following procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-81...
Page 128 * Description of the setting value Value Range correction Fixed Flexible After the adjustment is complete, make a copy and confirm the image quality.  Caution after the adjustment Nothing in particular e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-82...
Page 129: To Improve Reproducibility Of Red Seal Color
(2) Press [BASIC] on the control panel in the normal mode. Select “RED SEAL COLOR” among the original modes. After selecting “RED SEAL COLOR”, make a copy and check its image quality. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-83...
Page 130: To Reduce Streaks At Scanning With Df
The noise reduction level is high. After changing the setting value, perform printing and check its image quality. If an additional image quality adjustment is necessary, perform the following steps. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-84...
Page 131: When Adjusting The Image Quality Of The Full Color Mode
The noise reduction level is medium. High The noise reduction level is high. After changing the setting value, perform printing and check its image quality.  Caution after the adjustment Nothing in particular e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-85...
Page 132: To Change Gray Tone
 Caution after the adjustment Nothing in particular  Remarks The setting content of the values “2” and “4” is the same as that for the default (“0”). e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-86...
Page 133: The Color Reproduction Of The Back Side Differs From That For The Front Side At Dsdf Scanning
If you want to return the color reproduction of the back side at the DSDF scanning to the original one after the adjustment has been performed with this procedure, carry out the code [7002] in [08 SETTING MODE]. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-87...
Page 134: To Improve The Gradation Reproduction Of Dark Portions In Photos
* For the User custom mode, refer to “2.18 To Program Frequently Used Copy Settings (To Use Custom Mode)”. * The setting content of the default value “0” is the same as that for the setting value of each original mode as below. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-88...
Page 135 This adjustment will affect to that for set at (3) in “2.11.1 To Adjust the Copy Image Quality of a Black Logo”. When performing this adjustment, pay attention to the balance against the reproduction level of the black color logos, too. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 2-89...
Page 137: Restrictions On Use Of Printer Functions
> 3.14 To Clearly Print Light-Colored Thin Lines or Text * 600 dpi is recommended for images such as photographs or design drawings that require emphasis on colors or gradations. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 138: To Maintain A Steady Color Balance
Automatic calibration is the basic adjustment to accurately reproduce colors on the printouts. When you would like to accurately reproduce the desired hue or when you have replaced the consumables and changed the installation environment, perform automatic calibration to ensure the color reproducibility. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 139 (h) Place the printed test chart on the original glass. (i) Press the [START] button to perform calibration. When the calibration comes to an end, the message “Scanning and calibrating” will disappear. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 140: To Maintain A Steady Color Balance On Thick Paper Or Special Paper
* Perform the adjustment in accordance with the procedures below. * Only the service technician must use procedure (1). * Both the service technician and the user can use procedure (2). e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 141 * When you press [CALIBRATION], a chart is printed out and the calibration guide illustration is displayed on the control panel. Proceed to the next step. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 142 * If the chart is not properly placed, the message “Set chart correctly” is displayed on the control panel. In this case, return to step (j) and realign the chart. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 143: To Obtain The Desired Color Balance
* Perform the adjustment in accordance with the procedures below. * Both the service technician and the user can use procedures (1) and (2). * Only the service technician must use procedure (3). e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 144 * This adjustment will have an effect only on Auto or Color mode printing. Open the property page of the printer driver. Change the “Image Quality Type” option in the “Image Quality” tab. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 145 Windows (PS3) is performed (but not on Macintosh) or if a file created on the above applications is printed. However, the color balance may be changed, and also the image quality may be diminished, depending on the type of file. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 146 After changing the option on the printer driver, print and check the print image quality. If further image quality adjustments are still necessary, use the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-10...
Page 147 * Initially, change the value by 4 steps, while checking the printouts until the optimum value is obtained. • “Color Balance” tab: Change the “All Colors” or “Each Color” option • “Image Attribute” tab: Change the “Brightness” or “Saturation” option. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-11...
Page 148 After changing the option on the printer driver, print and check the print image quality. If further image quality adjustments are still necessary, the service technician must use the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-12...
Page 149 Detail 05-8275 0/1/2 Smooth 05-8045 0/1/2 Detail 05-8049 0/1/2 * Set the value in increments of approximately 20, while checking the printouts until the optimum value is obtained. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-13...
Page 151: To Closely Match The Color Balance On The Monitor
On commercially available monitors, sRGB is not selected as a color space by default. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-15...
Page 152 * This adjustment will have an effect only on Auto or Color mode printing. Open the property page of the printer driver. Select “Photograph” from among the “Image Quality Type” options. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-16...
Page 153 • In general, it is impossible to reproduce color saturation closely matching the true colors, as viewed on the monitor, because the range of colors reproducible in toner colors is narrower than the one on the monitor. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-17...
Page 154: To Maintain A Uniform Gray Hue (To Maintain Consistency In Gray Among Text, Photos And Graphics)
JPEG and TIFF. This provides a deeper gray on the printouts. Change the option on the printer driver, in order to maintain consistency in the gray hue between the drawing data and the image data. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-18...
Page 155 * This adjustment will have an effect only on Auto or Color mode printing. Open the property page of the printer driver. Click [Setting] in the “Image Quality” tab. Unmark the “Pure Gray” checkbox in the “Basic” tab. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-19...
Page 156 The adjustment allows gray areas always to be reproduced using all color toners (C, M, Y and K). As a result, undesired colors may look blended, depending on the print image. Therefore, carefully perform the adjustment, while checking the printouts. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-20...
Page 157: To Use Only The Black Toner To Reproduce Gray Areas (To Use Only The Black Toner To Reproduce Black-And-White Photos Or Gradational Images)
* Perform the adjustment in accordance with the procedure below. * Both the service technicians and the users can perform step (1). * Only the service technicians can perform step (2). e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-21...
Page 158 * The above table shows the sample combinations of when the Image Quality Type is “General”. When “Auto” is selected, the areas to be applied are automatically selected according to the Image Quality Type. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-22...
Page 159 The adjustment allows gray areas to always be reproduced using only the K toner. As a result, color photos may look more grained. Therefore, carefully perform the adjustment, while checking the printouts. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-23...
Page 161: To Easily Adjust The Overall Brightness
A darker print image is obtained. A brighter print image is obtained.  Explanation The brightness of the print image can be easily adjusted by changing the “Brightness” setting on the printer driver. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-25...
Page 162 • Select the desired value for brightness on a scale of -4 (Darkest) to 4 (Lightest). For Windows PCL6 Open the property page of the printer driver. Click [Setting] in the “Image Quality” tab. Change the “Brightness” option in the “Image Attribute” tab. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-26...
Page 163  Caution after the adjustment Nothing in particular.  Remarks The brightness adjustment does not affect black text (CMY = 100%, K = 100% or RGB = 0%). e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-27...
Page 164: To Adjust The Overall Saturation
The saturation is decreased. The saturation is increased.  Explanation The saturation of the print image can be easily adjusted by changing the “Saturation” option on the printer driver. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-28...
Page 165 (1) Change the “Saturation” option on the printer driver. For Windows PCL6 Open the property page of the printer driver. Click [Setting] in the “Image Quality” tab. Change the “Saturation” option in the “Image Attribute” tab. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-29...
Page 166 After changing the option on the printer driver, print and check the print image quality. Only if the saturation of R (Red) is still insufficient even after all the above procedures have been used, must the service technician use the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-30...
Page 167  Caution after the adjustment Nothing in particular.  Remarks The saturation adjustment does not affect black or gray areas on the printout. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-31...
Page 168: To Easily Adjust The Overall Contrast
The contrast is decreased. The contrast is increased.  Explanation The contrast of the print image can be easily adjusted by changing the “Contrast” option on the printer driver. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-32...
Page 169 • Select the desired value for contrast on a scale of -4 (Lowest) to 4 (Highest). For Windows PCL6 Open the property page of the printer driver. Click [Setting] in the “Image Quality” tab. Change the “Contrast” option in the “Image Attribute” tab. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-33...
Page 170 * This adjustment will have an effect only on full-color printing. Open the print dialog box. Change the "Color Settings 2" - “Contrast” option.  Caution after the adjustment Nothing in particular. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-34...
Page 171: To Obtain A Sharper Print Image
Increase the sharpness intensity under the menu on the printer driver, in order to obtain a sharper print image. * The sharpness adjustment will have an effect on photo images, such as BMP, GIF, JPEG and TIFF. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-35...
Page 172 Set the value for “Sharpness” within a range of “1” to “4” in the “Image Attribute” tab. • Setting “4” provides the sharpest print image. * Sharpness adjustment is not available when 1200 dpi is selected for PS3 printer driver. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-36...
Page 173 • Setting “4” provides the sharpest print image. After changing the options on the printer driver, print and check the print image quality. If further image quality adjustments are still necessary, use the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-37...
Page 174 The adjustment may possibly cause rough edges of the image contained in low-resolution bitmap data. As a result, outlined edges may look shaded, black bands may appear, and toner may be scattered around the lines. Therefore, carefully perform the adjustment, while checking the printouts. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-38...
Page 175: To Obtain A Softer Image
Decrease the sharpness intensity under the menu on the printer driver, in order to obtain a softer print image. * The sharpness adjustment will have an effect on photo images, such as BMP, GIF, JPEG and TIFF. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-39...
Page 176 • Setting “-4” provides the smoothest (softest) image. The value “OFF” of sharpness intensity adjustment is positioned as shown below. * Sharpness adjustment is not available when 1200 dpi is selected for PS3 printer driver. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-40...
Page 177 • Setting “-4” provides the smoothest (softest) print image. After changing the options on the printer driver, print and check the print image quality. If further image quality adjustments are still necessary, use the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-41...
Page 178 Especially text and lines on the background of a gradational image, and text in the Format AutoShape dialog box with transparency selected on Microsoft Office may be blurred. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-42...
Page 179: To Make Low-Resolution Data Look Finer (To Soften An Image)
When a low-resolution image is printed, the edges may be jagged. Decrease the sharpness intensity, in order to eliminate the jaggies from the print image. * The sharpness adjustment will have an effect particularly on photo images, such as BMP, GIF, JPEG and TIFF. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-43...
Page 180 • Setting “-4” provides the smoothest (softest) print image. The value “OFF” of sharpness intensity adjustment is positioned as shown below. * Sharpness adjustment is not available when 1200 dpi is selected for PS3 printer driver. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-44...
Page 181 • Setting “-4” provides the smoothest (softest) print image. After changing the options on the printer driver, print and check the print image quality. If further image quality adjustments are still necessary, use the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-45...
Page 182 Especially text and lines on the background of a gradational image, and text in the Format AutoShape dialog box with transparency selected on Microsoft Office may be blurred. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-46...
Page 183: To Eliminate Smudges From Highly Colored Text And Lines (To Prevent Toner Scattering Around Text And Lines Where A Large Amount Of Toner Is Used)
* Perform the adjustment in accordance with the procedures below. * Both the service technicians and the users can perform step (1). * Only the service technicians can perform steps (2) and (3). e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-47...
Page 184 * Always set “Uncheck”. Setting “-2” or a smaller value may provide blurred print images. * Sharpness adjustment is not available when 1200 dpi is selected for PS3 printer driver. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-48...
Page 185 Open the print dialog box and change the "Color Settings 2" - "filter" setting. After changing the options on the printer driver, print and check the print image quality e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-49...
Page 186 Note that when the setting value of this code is “0”, the image quality will not be changed even if the value is changed on the printer driver menu. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-50...
Page 187 • The adjustment may possibly cause dark areas such as making shades on photo images look unnaturally faint. Therefore, carefully perform the adjustment, while checking the printouts. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-51...
Page 188 • Enter the value mentioned in the procedures or one within the recommended value range for the adjustment. Otherwise, it may cause a loss in MFP performance, including degradation in the image quality and a reduction in the life of the consumables. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-52...
Page 189: To Clearly Print Light-Colored Thin Lines Or Text
* The item to set varies depending on the type of data to adjust. Select the effective option according to the data format to adjust, such as a print image (raster data), text (font), and line drawing (graphic data). e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-53...
Page 190: To Adjust The Print Image Quality In The Color Mode
"Detail" (To make the halftone screen high frequency) • Image Quality Type: "Line Art" (To make the color darker and enhance thin lines) Halftone: "Auto" or "Detail" (To make the halftone screen high frequency) e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-54...
Page 191 "Auto" or "Detail" (To make the halftone screen high frequency) After changing the options on the printer driver, print and check the print image quality. If further image quality adjustments are still necessary, use the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-55...
Page 192 * Initially, set "4" and check the printout. If further image quality adjustments are still necessary, refer to (5) to do this. * Sharpness adjustment is not available when 1200 dpi is selected for PS3 printer driver. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-56...
Page 193 "Contrast" or increasing "Saturation" (moving to [+] side) may improve the image quality. After changing the option on the printer driver, print and check the print image quality. If further image quality adjustments are still necessary, use the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-57...
Page 194 Note that when the setting value of this code is "0", the image quality will not be changed even if the value is changed on the printer driver menu. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-58...
Page 195 8049] or [8272 to 8275] to adjust the color balance and increase the color density. • Adjust the value for [05] code corresponding to the print option to be applied (PDL and Halftone). e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-59...
Page 196 * Whether to fix or change the maximum density in a high-density area can be selected by the setting of 05-8066. Area where the density is Subcode adjusted Low-density area Medium-density area High-density area e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-60...
Page 197 • Enter the value mentioned in the procedures or one within the recommended value range for the adjustment. Otherwise, it may cause a loss in MFP performance, including degradation in the image quality and a reduction in the life of the consumables. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-61...
Page 198: To Adjust The Print Image Quality In The Black And White Mode
* This adjustment will have an effect only on Black and white mode printing. PCL6 Open the property page of the printer driver. Click [Setting] in the "Image Quality" tab. Select "Detail" from among the "Halftone" options in the "Basic" tab. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-62...
Page 199 Open the print dialog box. Select "Color Settings 1" - "Detail" from among the "Halftone" options. After changing the option on the printer driver, print and check the print image quality. If further image quality adjustments are still necessary, use the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-63...
Page 200 * Initially, set "4" and check the printout. If further image quality adjustments are still necessary, refer to (5) to do this. * Sharpness adjustment is not available when 1200 dpi is selected for PS3 printer driver. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-64...
Page 201 "Contrast" or increasing "Saturation" (moving to [+] side) may improve the image quality. After changing the option on the printer driver, print and check the print image quality. If further image quality adjustments are still necessary, use the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-65...
Page 202 * This adjustment will have an effect only on printing on the Windows PCL6, XPS or PS3 emulation printer driver. (This adjustment cannot be performed on a Macintosh printer driver.) * Initially, set "4" and check the printout. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-66...
Page 203 0/1/2 Auto (Graphic) 05-7367 0/1/2 Auto (Image) 05-7368 0/1/2 * Set the value in increments of approximately 10, while checking the printouts until the optimum value is obtained. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-67...
Page 204 The adjustment may possibly cause outlined edges, jaggies and variations in gradation. As a result the photo image may look unnatural. Therefore, carefully perform the adjustment, while checking the printouts. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-68...
Page 205: To Make The Light-Colored Area Darker On The Printout
To print only the light area in a higher density and leave the dark area as it is, change the setting for the printer driver and adjust the background and color balance. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-69...
Page 206 (1) Open the property page of the printer driver and click [Setting] in the "Image Quality" tab. Set the "Background adjustment" option in the "Image Attribute" tab within the range of "1" to "4". e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-70...
Page 207 If further image quality adjustments are still necessary, the service technician must use the next procedure according to the image type. • To adjust the color image: Go to procedure (4). • To adjust the black and white image: Go to procedure (5). e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-71...
Page 208 Smooth 05-8271 (1200dpi) Detail 05-8275 Smooth 05-8045 Detail 05-8049 * Set the value in increments of approximately 20, while checking the printouts until the optimum value is obtained. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-72...
Page 209 PCL6 and Halftone = "Smooth" (or "Auto") selected.) Carefully perform the adjustment, being aware that the image quality of all future printouts will be changed, when printing out originals other than the one that is used for the adjustment. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-73...
Page 210 * The subcode varies according to the area where the density is adjusted. Refer to the table below and set the subcode for the area to be adjusted. Subcode Area where the density is adjusted Low-density area Medium-density area High-density area e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-74...
Page 211 (illustrations), and "Smooth" is applied to raster data (images). Therefore, particular attention is required since the adjustment may have a different impact according to the patterns of the image to be printed.  Caution after the adjustment Nothing in particular. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-75...
Page 212: To Clearly Print Thin Lines/Double Lines
(4) after checking the printed image. * Both the service technician and the user can use procedure (1). * Only the service technician must use procedures (2), (3) and (4). e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-76...
Page 213 For Windows PCL6 Open the property page of the printer driver. Click [Setting] in the "Image Quality" tab. Mark the "Distinguish Thin Line" checkbox in the "Basic" tab. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-77...
Page 214 If further image quality adjustment is necessary, the service technician shall use the following procedure because the color of the text of the original file may not be set as black: e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-78...
Page 215 If further image quality adjustments are necessary, follow the next step. However, the service technician shall judge whether or not the adjustment is to be performed in conjunction with the settings in steps (1) to (3). e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-79...
Page 217: To Decrease The Image Density And Save Toner (To Print In The Toner Save Mode)
 Procedures * Both the service technician and the user can perform all adjustments. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-81...
Page 218 (1) Enable the "Toner Save" option on the printer driver. For Windows PCL6 Open the property page of the printer driver. Mark the "Toner Save" checkbox in the "Others" tab. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-82...
Page 219 The print density in the toner save mode can also be adjusted. For further information regarding the adjustment procedures, refer to 3.18 To Adjust the Image Density in the Toner Save Mode. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-83...
Page 220: To Adjust The Image Density In The Toner Save Mode
Adjust the upper limit of the image density in the toner save mode, in order to obtain the desired image density requested by a particular user.  Procedures * The service technician must perform all adjustments. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-84...
Page 221 Set a value larger than 176 to increase the density. * Set the value in increments of approximately 10, while checking the printouts until the optimum value is obtained. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-85...
Page 222 The adjustment may possibly cause an increase of the amount of toner used (if the image density is increased) or provide faint print images (if the image density is decreased). Therefore, carefully perform the adjustment, while checking the printouts. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-86...
Page 223: To Print Illegible Gray Or Colored Text In Black
* This adjustment will have an effect only on printing on a Windows PCL6 or PS3 or XPS emulation printer driver. (This adjustment cannot be performed on a Macintosh printer driver.)  Procedures * Both the service technician and the user can perform all adjustments. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-87...
Page 224  Caution after the adjustment Nothing in particular.  Remarks Not all colored text may be printed in black, depending on the type of text (e.g. text larger than 72 points). e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-88...
Page 225: To Ignore Blank Pages For Printing
Change the option on the printer driver, in order to ignore all blank pages for printing.  Procedures * Both the service technician and the user can perform all adjustments. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-89...
Page 226 (1)Enable the "Do not Print Blank Pages" option on the printer driver. For Windows PCL6 Open the property page of the printer driver. Mark the "Do not Print Blank Pages" checkbox in the "Others" tab. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-90...
Page 227 If any data are inserted in the header or footer of a particular page on Excel or Word, even though no data are present in the body, the page will not be recognized as a blank page. The header or footer will be printed out. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-91...
Page 228: To Sharply Print Black Text
* Perform the adjustment in accordance with the procedures below. * Both the service technician and the user can use procedures (1), (2), (4) and (5). * Only the service technician must use procedures (3) and (6). e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-92...
Page 229 Open the property page of the printer driver. Click [Setting] in the "Image Quality" tab. Mark the "Pure Black" checkbox in the "Basic" tab. Select "Text, Graphic & Image" from among the "Apply to" options. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-93...
Page 230 "Pure Black and Gray" options. After changing the option on the printer driver, print and check the print image quality. If further image quality adjustments are still necessary, use the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-94...
Page 231 If the graphic and image options are changed, the adjustment may possibly cause the unnatural hue of gradational and photo images, and the inadequate reproducibility of gradations. Therefore, carefully perform the adjustment, while checking the printouts. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-95...
Page 232 If further image quality adjustments are still necessary, the service technician must use the next procedure, because text may not be defined as 100% black on the file. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-96...
Page 233 > Change the values for Y: 05-8050, M: 05-8051, C: 05-8052 and K: 05-8053. * Printing on Macintosh is performed in PostScript. (See the "PS3" row in the table below.) e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-97...
Page 234 Detail 05-8275 0/1/2 Smooth 05-8045 0/1/2 Detail 05-8049 0/1/2 * Set the value in increments of approximately 20, while checking the printouts until the optimum value is obtained. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-98...
Page 236 Use "Output Preview" on Acrobat Professional to examine the color definition on the PDF file. * For further information regarding the Output Preview, refer to an appropriate manual or the Help menu of Acrobat Professional. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-100...
Page 237 Ink Simulation, in order to print CMYK data from among the "Simulation Profile" options. (4) Move the cursor over the data to check the color definition. Then the color calibration will be displayed in percentage on "Separations." e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-101...
Page 238: To Prevent Dark Toner From Coming Off
This adjustment does not affect a single color of C, M, Y and K, or bright colors such as red and green. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-102...
Page 239  Caution after the adjustment The adjustment may possibly cause dark areas such as shades on photo images to look unnaturally faint. Therefore, carefully perform the adjustment, while checking the printouts. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-103...
Page 240: To Register The Image Quality Adjusted Corresponding To A Preference (To Use The Custom Color Settings)
Mark the "Detail" checkbox in the "Color Balance" tab. Click [Edit]. Set the value for the Middle density of the color in the "Color Balance Details" option. After setting the values, use the procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-104...
Page 241 (b) Enter an optional name in the "Name" option. (c) Select the type you would like to use as the base one from among the "Image Quality Type" options in "Original Image Quality Type." e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-105...
Page 242 The checkbox in the "Custom Color Settings" option will be effective, only if you login using a user name belonging to Administrator or Power Users, and open the property page of the printer driver in the "Printers and Faxes" folder. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-106...
Page 243: To Print A Full-Color Original In Two Colors
* The procedure to use varies depending on whether "To Adjust Colors", "To Adjust the Sharpness" or "To Print a Full-Color Original in Two Colors". Refer to the procedure corresponding to the particular user’s request. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-107...
Page 244: To Adjust Colors
Open the property page of the printer driver. Select "Twin Color" from among the "Color" options in the "Basic" tab. Click [Details]. Select the color to be used for the area other than black, from among the "Color" options. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-108...
Page 245 • To obtain a shaper or softer print image: Go to procedure (2). • To make only the light-colored area darker: Go to procedure (3). e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-109...
Page 246 - "Color Balance" tab: Change the "All Colors" or "Each Color" option. - To make detailed setting, you can set it by marking "Detail" checkbox. (Same as Auto color or Full color mode) e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-110...
Page 247 05-8032 0/1/2 Red/Green/ Blue/Cyan/ K(Black) 05-8023 0/1/2 Magenta/ Yellow * Set the value in increments of approximately 20, while checking the printouts until the optimum value is obtained. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-111...
Page 248  Caution after the adjustment If "White" is selected in the Twin-color mode, all areas other than black will not be printed. White toner will not be used to print these areas. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-112...
Page 249: To Adjust The Sharpness
Open the property page of the printer driver. Select "Twin Color" from among the "Color" options in the "Basic" tab. Click [Details]. Select the color to use for the area other than black, from among the "Color" options. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-113...
Page 250 Open the property page of the printer driver. Click [Setting] in the "Image Quality" tab. Set the value for "Sharpness" within a range of "-4" to "4" or to "OFF" in the "Image Attribute" tab. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-114...
Page 251: To Print A Full-Color Original In Two Colors
Acceptable Apply to [05] code Recommended value Default value range Text 8213 Increase the set value to Graphic 8214 1 to 255 enlarge the black area. Image 8215 e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-115...
Page 252: To Use Icc Profile
Each Ink Manufacturer", "To Print Using Custom RGB Profiles", "To Convert Colors with Specified Source ICC Profiles (Not Using Embedded ICC Profiles)" or "To Perform Further Adjustment After Using ICC Profiles", according to the request from the user. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-116...
Page 253: To Create Icc Profiles For Printing On The Paper To Be Used
* Both the service technician and the user can perform all settings. (1) Open the Properties page of the printer driver and then select the paper type on the "Paper Type" option on the "Basic" tab menu. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-117...
Page 254 (3) Select the desired type of halftone on the "Halftone" option on the "Basic" tab menu. * It is not recommended to select "Auto" on this option because several types of halftone may be used on the same page. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-118...
Page 255 (4) Select the desired resolution level on the "Resolution" option. * "1200 dpi" is selectable only for PS3 printer driver. (5) Uncheck "Use Sharpness Filter" on the "Image Attribute" tab menu. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-119...
Page 256 (6) Select "None" on the "CMYK Source Profile" option on the "Advanced" tab menu. * At this step you can set any printer profile. (7) Uncheck "Apply to Device Color Only". e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-120...
Page 257 • Read the precautions provided by the ICC profile creation software carefully before starting printing. • The correct image may not be printed on some paper types that are out of the MFP’s specifications. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-121...
Page 258: To Print Precise Colors Using Existing Rgb Source Icc Profiles
• Follow (a) to (g) below to upload the profiles. (a) Access TopAccess and open the "Administration" tab menu. (b) Open the "Setup" menu and the "ICC Profile" submenu. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-122...
Page 259 * The display returns to the "ICC Profile" submenu. (f) Click [Save]. * A confirmation dialog box is displayed. (g) Click [OK]. * For the details of TopAccess, see the TopAccess Guide. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-123...
Page 260 (3) Open the Properties page of the printer driver and then select "Advanced" on the "Image Quality Type" option on the Image Quality" tab menu. Then click [Setting]. (4) Select the uploaded RGB profile on "RGB Source Profile" on the "Advanced " tab menu. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-124...
Page 261 • Not all colors may be printed precisely because the color gamut reproducible with MFPs differs depending on the models. • The accuracy of color reproduction differs depending on printer profiles used. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-125...
Page 262: To Perform Simulated Printing With Cmyk Inks Of Each Ink Manufacturer
• Follow (a) to (g) below to upload the profiles. (a) Access TopAccess and open the "Administration" tab menu. (b) Open the "Setup" menu and the "ICC Profile" submenu. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-126...
Page 263 * The display returns to the "ICC Profile" submenu. (f) Click [Save]. * A confirmation dialog box is displayed. (g) Click [OK]. * For the details of TopAccess, see the TopAccess Guide. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-127...
Page 264 (3) Open the Properties page of the printer driver and then select "Advanced" on the "Image Quality Type" option on the Image Quality" tab menu. Then click [Setting]. (4) Select the uploaded CMYK profile on "CMYK Source Profile" on the "Advanced" tab menu. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-128...
Page 265 • Not all colors may be printed precisely because the color gamut reproducible with MFPs differs depending on the models. • The accuracy of color reproduction differs depending on printer profiles used. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-129...
Page 266: To Print Using Custom Rgb Profiles
• Follow (a) to (g) below to upload the profile. (a) Access TopAccess and open the "Administration" tab menu. (b) Open the "Setup" menu and the "ICC Profile" sub menu. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-130...
Page 267 * The display returns to the "ICC Profile" sub menu. (f) Click [Save]. * A confirmation dialog box is displayed. (g) Click [OK]. * For the details of TopAccess, see the TopAccess Guide. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-131...
Page 268 (3) Open the Properties page of the printer driver and then select "Advanced" on the "Image Quality Type" option on the "Image Quality" tab menu. Then click [Setting]. (4) Select the uploaded ICC profile on "Custom RGB profile" on the "Advanced" tab menu. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-132...
Page 269: To Convert Colors With Specified Source Icc Profiles (Not Using Embedded Icc Profiles)
• Follow (a) to (g) below to upload the profiles. (a) Access TopAccess and open the "Administration" tab menu. (b) Open the "Setup" menu and the "ICC Profile" submenu. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-133...
Page 270 * The display returns to the "ICC Profile" submenu. (f) Click [Save]. * A confirmation dialog box is displayed. (g) Click [OK]. * For the details of TopAccess, see the TopAccess Guide. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-134...
Page 271 (3) Open the Properties page of the printer driver and then select "Advanced" on the "Image Quality Type" option on the Image Quality" tab menu. Then click [Setting]. (4) Select the uploaded profile on "RGB Source Profile" or "CMYK Source Profile" on the "Advanced" tab menu. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-135...
Page 272 3. Printer-specific Adjustments (5) Uncheck "Apply to Device Color Only". (6) Select the uploaded printer profile on "Profile" of the "Destination Profile" option. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-136...
Page 273: To Perform Further Adjustment After Using Icc Profiles
(1) Open the Properties page of the printer driver and then select "Advanced" on the "Image Quality Type" option on the "Image Quality" tab menu. Then click [Setting]. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-137...
Page 274 (2) Select the desired profiles on "RGB Source Profile", "CMYK Source Profile" or "Profile" of the "Destination Profile" option. (3) Open the "Color Balance" tab menu and then change each setting items to obtain the desired color balance. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-138...
Page 275 3. Printer-specific Adjustments (4) Open the "Image Attribute" tab menu and then change each setting items to obtain the desired image quality.  Caution after the adjustment Nothing in particular. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-139...
Page 276: To Improve The Reproducibility Of Red Seal Color
Open the property page of the printer driver. Select “General” in the “Original Image Quality Type” box in the “Image Quality” tab, and then click [Setting]. Mark the “Red Seal Color Mode” checkbox in the “Basic” tab. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-140...
Page 277 Open the print dialog box. Select the "Color Settings 1" - “Red Seal Color Mode” check box. After changing the setting on the printer driver, print the image and check its image quality. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-141...
Page 278: To Suppress The Unevenness On Images
When the low screen ruling is set, jaggedness may appear on diagonal or curved lines. In this case, check the printed image and then switch the setting if necessary e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-142...
Page 279: To Suppress Color Misalignment
Perform the adjustment while checking the images, since the outline form of the boundary of the text or graphics will be accentuated if the effectiveness of the trapping is enhanced.  Remarks Nothing e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-143...
Page 280: To Adjust Smudged Black Text And Black Thin Lines
Type" options are available in the "Color Settings 1" menu in the print dialog box on Macintosh. <Notes> This adjustment is available only when the resolution is 600dpi. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-144...
Page 281 1200dpi Black 7305  Caution after the adjustment Perform the adjustment while checking the printed images since faint black text or black thin lines may occur. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-145...
Page 282: To Perform Fine Adjustment Of Print Ratio For Front Side At Duplex Printing
- Depending on the hygroscopic condition of the paper, its size will be changed in duplex printing and thus the image sizes between the front and back sides will deviate. In such a case, reattempt the adjustment as required. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-146...
Page 283 (d) Close the property of the printer and then open it again. (e) Click [Preferences...] and check that the "Enable adjustment of image position for duplex" check box is displayed in the [Other] tab. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-147...
Page 284 * Make sure that the "Enable adjustment of image position for duplex" check box has been selected. (g) Measure the amount of the deviation in the end edge of the front and back sides in the primary and secondary scanning directions. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-148...
Page 285 Primary scanning 4957 direction Special 2 Secondary scanning 4957 direction Primary scanning 4958 direction Special 3 Secondary scanning 4958 direction Primary scanning User Media 4959 Type 1 direction e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-149...
Page 286 Secondary scanning 4966 direction Primary scanning 4967 direction User Media Type 9 Secondary scanning 4967 direction Primary scanning 4968 direction User Media Type 10 Secondary scanning 4968 direction e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-150...
Page 287 Check that [Adjustment Position in Duplex Print (reduction ratio)] is displayed in TopAccess - [Administration] - [Printer]. * The setting procedure is the same as that for (4). e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 3-151...
Page 289: E-Filing-Specific Adjustments
This may make a dark area blurred and a light area eliminated. Adjust the threshold value, in order to clearly store the black-and-white original in the Auto color mode. * This adjustment will have an effect on the image stored using Scan to File and Scan to E-mail. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 290 The data will increase in size, compared to those in the binary mode. • The adjustment of density will be effective, only if "STANDARD" is selected from among the "IMAGE QUALITY FOR BLACK IN ACS" options. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 291: To Store An Original While Reducing The File Size
* This adjustment will have an effect on images stored using Scan to File and Scan to E-mail.  Procedures * Both the service technician and the user can perform all adjustments. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 292 If the full-color or gray-scale image is copied or printed and stored in the e-Filing box (Copy to Box or Print to Box), the user can select a desired compression rate, when downloading the image using File Downloader on a client PC. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 293: To Match The Color Balance On The Original (To Adjust The Color Balance In Print To Box)
The image stored in the e-Filing box looks The color balance of the image stored is closely different in the color balance from the original. matched with that of the original. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 294 * "General" allows the image to be stored in colors, which are closely matched with the original, compared to the other Image Quality Type options.  Caution after the adjustment Nothing in particular. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 295: To Scan And Print, While Minimizing Moiré
After changing the original mode, scan and store the original. Then print and check the print image quality. If further image quality adjustments are still necessary, use other procedures. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 296 When the original containing text and lines is scanned and printed, the adjustment may possibly cause the blurred text and lines or a blend of undesired colors. Therefore, carefully perform the adjustment, while checking the scanned-in image or printout. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 297: To Finely Print The Image Stored In The E-Filing Box (To Print Images Stored Through Copy To Box Or Print To Box)
If the image is printed out directly from the e- downloaded to a PC and then printed out, the Filing box, the image quality will be image data conversion may diminish the image maintained. quality. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 298 Note that files created through the Archive Document or Backup feature cannot be directly opened on the PC or printed out. For further information regarding Archive Document and Backup, refer to the e-Filing Guide. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 4-10...
Page 299: To Store An Image Suitable For Displaying On The Monitor Or Image Editing
Box. This can avoid unnecessary data optimized for printing on paper. This may conversion. As a result, the image quality can diminish the image quality. be maintained. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 4-11...
Page 300 * For further information regarding how to scan and store images, refer to the Operator’s Manual for e-Filing Guide and Scanning Guide.  Caution after the adjustment Nothing in particular. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 4-12...
Page 301: To Finely Print Color Images Scanned And Stored (To Print Images Stored Through Scan To Box)
When the printing image mode suitable for the printing may be performed with image stored data is selected, the data can be printed processing not suitable for the stored data. finely with optimal image processing. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 4-13...
Page 302 (3) Print out the image stored in the e-Filing box on the Control Panel or using the e-Filing Web utility. * For further information regarding how to print it out, refer to the Operator’s Manual for e-Filing Guide.  Caution after the adjustment Nothing in particular. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 4-14...
Page 303: Appendix
Scan to Box be displayed on a computer monitor. computer monitor To print color images stored with the scanning Scan to Box Printing on paper function more clearly. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 4-15...
Page 305: Scanning-Specific Adjustments
* [MID] is selected from among the compression rate options by default. After changing the compression rate, scan the original and check the scanned-in image quality. If further image quality adjustments are still necessary, use procedure (2). e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 306 • Gray scale mode: 600 / 400 / 300 / 200 / 150 / 100 (dpi) • Black mode: 600 / 400 / 300 / 200 / 150 / 100 (dpi) e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 307: To Scan An Original, While Eliminating The Background Color (To Eliminate The Background Density)
After decreasing the background density, scan the original and check the scanned-in image quality. With the background density set to the minimum, if further image quality adjustments are still necessary, the service technician must use the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 308 (d) Press [Next] twice to display the menu to change the initial values for the Full color and Auto color modes. (e) Select the default background density in the "BACKGROUND ADJUSTMENT" option. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 309: To Clearly Scan And Print An Original In Black And White (To Improve Gradation And Reduce Graininess)
Gray scale mode. • If the file size in the Black mode with the Photo mode selected is 1, it will be approximately doubled in the Gray scale mode. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 310: To Scan The Original, While Reducing The File Size
Scanning the Original" in order to reduce the file size without changing the file format. Refer to "To Reduce the File Size in Slim PDF" in order to give a higher priority to the file size reduction than the image quality. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 311: To Reduce The File Size By Changing The Options When Scanning The Original
Gray scale mode. After changing the compression rate, scan the original and check the scanned-in image quality. If further image quality adjustments are still necessary, use other procedures. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 312 • Correlation between the compression rate and the file size (procedure (3)) * The file size is 100%, with [MID] selected. Compression rate File size ratio 100% Approx. 80% e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 313 • Remember that when scanning the original in the Full color mode, if the original mode option is switched from the Text/Photo mode or the Photo to the Text mode, the file size may become larger. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved...
Page 314: To Reduce The File Size In Slim Pdf
After changing the "ROTATION" option, scan the original and check the scanned-in image quality. If further image quality adjustments are still necessary, the service technician must use the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 5-10...
Page 315  Caution after the adjustment The adjustment may possibly cause blurred text, noise or vary the hues of areas. Therefore, carefully perform the adjustment, while checking the scanned-in image quality. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 5-11...
Page 316: To Sharply Scan The Original (To Increase The Sharpness Intensity)
Adjust the sharpness intensity, in order to sharply scan the soft and blurred original. * This adjustment will have an effect on the image scanned in all color modes (Full color, Gray scale, Black and Auto color). e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 5-12...
Page 317 The adjustment may possibly cause moiré. In addition, when text and thin lines in a light-colored background are scanned, the background around the text or line may be eliminated. Therefore, carefully perform the adjustment, while checking the scanned-in image. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 5-13...
Page 318: To Scan An Original, While Enhancing Black
* This adjustment will have an effect only on the image scanned in the Full color mode (including the Auto color mode). e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 5-14...
Page 319 * Setting "0" provides the lightest black, while setting "4" the darkest.  Caution after the adjustment The adjustment may possibly provide the extremely dark background. Therefore, carefully perform the adjustment, while checking the scanned-in image. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 5-15...
Page 320: To Scan An Original With The Desired Gradation
(gradation). Adjust the gamma curve balance, in order to change the gradation, depending on the type of original or at a user’s request. * This adjustment will have an effect only on the image scanned in the Black mode or the Gray scale mode. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 5-16...
Page 321 * Gradation in the Black mode will vary, if the medium-density area is mainly adjusted. But remember that adjusting the low- or high-density area will rarely affect the gradation in the Black mode.  Caution after the adjustment Nothing in particular. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 5-17...
Page 322: To Register The Original Mode Optimal For A Particular Type Of Original (To Have "Custom" Selected)
For the Full color mode Value for 08-8303 Reference original mode Reserved (Default) Text/Photo Text Photo e-document After selecting the reference original mode option, use the next procedure. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 5-18...
Page 323 After adjusting the value in the Custom mode, use the next procedure. (3)When scanning the original, press [SCAN SETTING] on the Control Panel. Select "Custom" from among the original mode options.  Caution after the adjustment Nothing in particular. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 5-19...
Page 324: To Eliminate Shading Around Scanned Images
"24" to 1 mm. * When the value increases, the white void around the scanned image becomes wider, and the data on the image decrease. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 5-20...
Page 325: To Scan Yellow Clearly
(a) Set G (green) to [+] side in Color Balance. (b) Set R (red) to [-] side in Color Balance. (c) Set the color balance with a combination of both (a) and (b). e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 5-21...
Page 326 • This adjustment influences not only yellow but also other colors. After adjusting the color balance, copy and check the copy image quality.  Caution after the adjustment Nothing in particular. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 5-22...
Page 327: To Reduce Streaks In Scanning With Df
None The noise reduction function is disabled. (Default) The noise reduction level is low. Middle The noise reduction level is medium. High The noise reduction level is high. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 5-23...
Page 328 After changing the setting value, perform scanning and check its image quality.  Caution after the adjustment Perform the adjustment while checking the scanned images since the adjustment may decrease the reproducibility of fine characters and lines. e-STUDIO5506AC/6506AC/7506AC (Ver01) © 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved 5-24...

This manual is also suitable for:

E-studio5506ac E-studio7506ac

Toshiba e-Studio6506AC Imaging Manual

1 General Adjustments - Copying, Printing and E-Filing (Output from Box)

2 Copier-Specific Adjustments

3 Printer-Specific Adjustments

4 E-Filing-Specific Adjustments

Appendix

5 Scanning-Specific Adjustments

Quick Links

Related Manuals for Toshiba e-Studio6506AC

Summary of Contents for Toshiba e-Studio6506AC

This manual is also suitable for:

Table of Contents