YASKAWA P1000 Quick Start Manual page 207

No.
(Addr. Name
Hex)
H3-05 Terminal A3 Signal Level
(413) Selection
H3-06 Terminal A3 Function
(414) Selection
H3-07
(415)
Terminal A3 Gain Setting
H3-08
(416)
Terminal A3 Bias Setting
H3-09 Terminal A2 Signal Level
(417) Selection
H3-10 Terminal A2 Function
(418) Selection
H3-11
(419)
Terminal A2 Gain Setting
H3-12
(41A)
Terminal A2 Bias Setting
H3-13 Analog Input Filter Time
(41B) Constant
H3-14 Analog Input Terminal
(41C) Enable Selection
H3-16
Terminal A1 Offset
(2F0)
H3-17
Terminal A2 Offset
(2F1)
H3-18
Terminal A3 Offset
(2F2)
H3-oo
Function
Setting
0 Frequency bias
1 Frequency gain
2 Auxiliary frequency reference 1
3 Auxiliary frequency reference 2
4 Output voltage bias
5 Accel/decel time gain
YASKAWA ELECTRIC TOEP YAIP1U 01B YASKAWA AC Drive - P1000 Quick Start Guide
0: 0 to 10 V
1: -10 to 10 V
2: 4 to 20 mA
3: 0 to 20 mA
Note: Use Jumper S1 to set input terminal A3 for a current or voltage
input signal.
Sets the function of terminal A3.
Sets the level of the input value selected in H3-06 when 10 V is input at
terminal A3.
Sets the level of the input value selected in H3-06 when 0 V is input at terminal
A3.
0: 0 to 10 V
1: -10 to 10 V
2: 4 to 20 mA
3: 0 to 20 mA
Note: Use Jumper S1 to set input terminal A2 for a current or voltage
input signal.
Sets the function of terminal A2.
Sets the level of the input value selected in H3-10 when 10 V (20 mA) is input
at terminal A2.
Sets the level of the input value selected in H3-10 when 0 V (0 or 4 mA) is
input at terminal A2.
Sets a primary delay filter time constant for terminals A1, A2, and A3. Used
for noise filtering.
Determines which analog input terminals will be enabled when a digital input
programmed for "Analog input enable" (H1-oo = C) is activated.
1: Terminal A1 only
2: Terminal A2 only
3: Terminals A1 and A2 only
4: Terminal A3 only
5: Terminals A1 and A3
6: Terminals A2 and A3
7: All terminals enabled
Adds an offset when the analog signal to terminal A1 is at 0 V.
Adds an offset when the analog signal to terminal A2 is at 0 V.
Adds an offset when the analog signal to terminal A3 is at 0 V.
H3 Multi-Function Analog Input Settings
10 V = E1-04 (maximum output frequency)
0 to 10 V signal allows a setting of 0 to 100%. -10 to 0 V signal allows a setting of -100
to 0%.
10 V = E1-04 (maximum output frequency)
10 V = E1-04 (maximum output frequency)
10 V = E1-05 (motor rated voltage)
10 V = 100%
B.6 H Parameters: Multi-Function Terminals
Description
Description
Values Page
Default: 0
111
Range: 0 to 3
Default: 2
111
Range: 0 to 26
Default: 100.0%
Min.: -999.9 111
Max.: 999.9
Default: 0.0%
Min.: -999.9 111
Max.: 999.9
Default: 2
112
Range: 0 to 3
Default: 0
112
Range: 0 to 26
Default: 100.0%
Min.: -999.9 112
Max.: 999.9
Default: 0.0%
Min.: -999.9 112
Max.: 999.9
Default: 0.03 s
Min.: 0.00 –
Max.: 2.00
Default: 7
–
Range: 1 to 7
Default: 0
Min.: -500 –
Max.: 500
Default: 0
Min.: -500 –
Max.: 500
Default: 0
Min.: -500 –
Max.: 500
Page
–
–
–
–
–
–
207
B