Siemens SIPROTEC 7SD610 Manual page 396

Appendix
A.7 Settings
Addr. Parameter
3932 T-PoleDiscrep.
4001 FCT TripSuperv.
4002 No. of BI
4003 Alarm Delay
4101 REF PROT.
4111 I-REF>
4112A T I-REF>
4113A SLOPE
4201 Ther. OVERLOAD
4202 K-FACTOR
4203 TIME CONSTANT
4204 Θ ALARM
4205 I ALARM
4206 CALC. METHOD
4501 STATE PROT I 1
4502 CONNEC. 1 OVER
4505A PROT 1 T-DELAY
4506A PROT 1 UNSYM.
4509 T-DATA DISTURB
4510 T-DATAFAIL
4511 PI1 SYNCMODE
4512 Td ResetRemote
4513A PROT1 max ERROR
4515A PI1 BLOCK UNSYM
4701 ID OF RELAY 1
4702 ID OF RELAY 2
4710 LOCAL RELAY
4801 GPS-SYNC.
4803A TD GPS FAILD
396
Function C
Breaker Failure 0.00 .. 30.00 sec; ∞
TripCirc.Superv ON
OFF
TripCirc.Superv 1 .. 2
TripCirc.Superv 1 .. 30 sec
REF OFF
ON
REF 1A 0.05 .. 2.00 A
5A 0.25 .. 10.00 A
REF 0.00 .. 60.00 sec; ∞
REF 0.00 .. 0.95
Therm. Overload OFF
ON
Alarm Only
Therm. Overload 0.10 .. 4.00
Therm. Overload 1.0 .. 999.9 min
Therm. Overload 50 .. 100 %
Therm. Overload 1A 0.10 .. 4.00 A
5A 0.50 .. 20.00 A
Therm. Overload Θ max
Average Θ
Θ from Imax
Prot. Interface ON
OFF
Prot. Interface F.optic direct
Com conv 64 kB
Com conv 128 kB
Com conv 512 kB
C37.94 1 slot
C37.94 2 slots
C37.94 4 slots
C37.94 8 slots
Prot. Interface 0.1 .. 30.0 ms
Prot. Interface 0.000 .. 3.000 ms
Prot. Interface 0.05 .. 2.00 sec
Prot. Interface 0.0 .. 60.0 sec
Prot. Interface TEL and GPS
TEL or GPS
GPS SYNC OFF
Prot. Interface 0.00 .. 300.00 sec; ∞
Prot. Interface 0.5 .. 20.0 %
Prot. Interface YES
NO
Diff.-Topo 1 .. 65534
Diff.-Topo 1 .. 65534
Diff.-Topo relay 1
relay 2
Prot. Interface ON
OFF
Prot. Interface 0.5 .. 60.0 sec
Setting Options Default Setting
2.00 sec
OFF
2
2 sec
OFF
0.15 A
0.75 A
0.00 sec
0.00
OFF
1.10
100.0 min
90 %
1.00 A
5.00 A
Θ max
ON
F.optic direct
30.0 ms
0.100 ms
0.10 sec
6.0 sec
TEL and GPS
0.00 sec
1.0 %
YES
1
2
relay 1
OFF
2.1 sec
C53000-G1176-C145-6, Release date 02.2011
Comments
Trip delay with pole discrepancy
TRIP Circuit Supervision is
Number of Binary Inputs per trip
circuit
Delay Time for alarm
Restricted Earth Fault Protection
Pick up value I REF>
T I-REF> Time Delay
Slope of Charac. I-REF> = f(I-
SUM)
Thermal overload protection
K-Factor
Time Constant
Thermal Alarm Stage
Current Overload Alarm Setpoint
Method of Acquiring Tempera-
ture
State of protection interface 1
Connection 1 over
Prot 1: Maximal permissible
delay time
Prot 1: Diff. in send and receive
time
Time delay for data disturbance
alarm
Time del for transmission failure
alarm
PI1 Synchronizationmode
Remote signal RESET DELAY
for comm.fail
Prot 1: Maximal permissible error
rate
Prot.1: Block. due to unsym.
delay time
Identification number of relay 1
Identification number of relay 2
Local relay is
GPS synchronization
Delay time for local GPS-pulse
loss
SIPROTEC, 7SD610, Manual